ILY Enterprise CoolCopy 3 User manual









User’s Manual
CoolCopyD1AL(DVD-Backup)
CoolCopyD 3
CoolCopyD 7
















Copyright©2005 ILY Enterprise, Inc. All rights reserved.
2
. Table of Contents
Chapter 1 Introduction .................................................................4
1.1 Overview ....................................................................................4
1.2 Features .....................................................................................4
1.3 Specifications ............................................................................4
Chapter 2 Installation Procedure .............................................5
2.1 Controller only ........................................................….…..........5
2.2 Whole duplicator without writer installed ..….........................5
2.3 Completed duplication system ...................….........................5
Chapter 3 Key Functions and Operating Instruction ……8
Chapter 4 Function ..........................................................….......…9
4.1 Copy ................................................................…........................9
4.2 Test ....................................................................................…..…9
4.3 Test&Copy ...........................................................…....…...........10
4.4 Verify ....................................................................…..................10
4.5 Compare ..............................................................…...............…11
4.6 Prescan ................................................................…..................11
4.7 Disc Info ........................................................................…….....12
4.8 Select Source................................................................….........12
4.9 Image .........................................................................................12
4.9.1 Load .....................................................................................13
4.9.2 Delete Image ........................................................................13
4.9.3 Image Info .............................................................................13
4.9.4 Compare Image ....................................................................14
4.9.5 Select Partition ......................................................................14
4.9.6 Select Src Drive ....................................................................15
4.10 Edit Track ...............................................................................15
4.10.1 CD to CD Edit......................................................................16
4.10.2 CD to HD ............................................................................17
4.10.3 Play Audio Track ................................................................18
4.10.4 Close Session ....................................................................18
4.11 Setup.........................................................................................19
4.11.1 Language (optional)....................................................…......19
4.11.2 Burn Speed .........................................................................19
4.11.3 Read Speed ........................................................................19
4.11.4 Auto Start Drive ...................................................................20
4.11.5 Start up menu ......................................................................20
4.11.6 Auto Verify ...........................................................................20

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
3
4.11.7 Auto Compare ......................................................................20
4.11.8 Auto Prescan .......................................................................21
4.11.9 Eject Disc ............................................................................21
4.11.10 Burn on The Fly ................................................................21
4.11.11 Burn Mode ........................................................................21
4.11.12 Button Sound ....................................................................22
4.11.13 Device Info ....................................................................…22
4.11.14 System Info .......................................................................23
4.11.15 Quick Erase ......................................................................23
4.11.16 Full Erase ..........................................................................23
4.12 Adv Setup...................................................................................24
4.12.1 UnderRun Protect ...............................................….............24
4.12.2 Overburn ...............................................................…...........24
4.12.3 Read Error Skip............... ..................................…..…... ...24
4.12.4 Format Hard Disk ....................................................….........24
4.12.5 Verify HDD ...............................…..................................…...25
4.12.6 Burn-in.................................................…...…........................25
4.12.7 Update Firmware..........................................................….....25
4.12.8 Compare Firmware .......................................................…....26
4.12.9 H/W Diagnostic ...............................................................…..26
4.12.10 Load Default ..................................................................….26
Chapter 5 Troubleshooting .........................................................27

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
4
Chapter 1 Introduction
1.1 Overview
People who want to create multiple copies of their DVDs or CDs usually take a long time to do so.
They might not have enough DVD+RW drives or they might be using their computers for some
other important tasks. The duplication process noticeably slows down a computer during the
burn process. Rather than sit at the computer for hours duplicating discs one at a time, it is much
more efficient to use a CoolCopyD DVD/CD duplication system.
The CoolCopyD DVD Duplicator system is a standalone duplicator and does not need to be
connected to a computer. It can duplicate discs accurately and quickly. With its multi-function
LCD panel, CoolCopyD DVD Duplicator is easy for any user to operate. It is a cost-efficient DVD-
R duplicator for audio, data, and video applications. The simple control panel is designed to
provide copy mode selection and copy operation.
1.2 Features
•Standalone IDE to IDE DVD Copy controller
•2(CoolCopyD1AL(DVD-Backup)) / 4(CoolCopyD3) / 8(CoolCopyD7) /
16(CoolCopyD14)
independent IDE channel
•Self system diagnostics when power on
•Supports Hard Drive image
•Auto format detection
•User friendly interface with message rich LCD display
•Fast copies supports high speed DVD-RW writing mode
•Easy operation without software and training are required
•Firmware upgrade via DVD-ROM
1.3 Specification
Power requirement – voltage: 5VB+/- 5%
Current: 0.5A Max.
Environment - Temperature
Operating 0˚ C to 70˚ C
Storage -20˚ C to 85˚ C
Humidity - 15% to 90%
Models: CoolCopyD3/CoolCopyD7
Dimensions - Length: 200 mm
Width: 146.2 mm
Height: 42 mm
Connectors - 40-pin internal IDE connector
Cable (Optional) - Using ATA-66 (*Cable of length do not use longer than 46cm)
DVD Format - DVD-ROM (Mode1 & Mode2), DVD-ROM/XA (Mode2 form1 & form2),
DVD-DA,
Mixed-Mode, Video DVD, DVD-I, Karaoke CD, Photo CD (Single & Multi-
session), CD-Extra, HFS, CD Bridge, ISO9660, CD-R, and DVD+RW

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
5
Writing mode - Auto Detect (DAO, TAO)
Supported DVD-ROM Drive* - EPO, TEAC
Supported DVD-RW Drive* - Plextor, TEAC, Lite-On, Asus, SONY
Chapter 2 Installation Procedure
When you purchase the CoolCopyD DVD Duplicator, the package may be packaged in the
following ways: controller only, whole duplicator without writer installed or a complete duplication
system.
2.1 Controller only
1. Before the installation, please prepare the necessary devices as following:
•DVD-ROM drive
•DVD-R/RW drive
•IDE case (2~10-bay chassis suggested).
•Hard drive and mobile rack (IDE-bus hard drive-Option)
•Switching power supply (300W suggested).
2. After the preparation as above and make sure:
•All IDE devices must be in master mode.
2.2 Whole duplicator without writer installed
•Unpack the duplicator.
•Prepare the DVD-R/RW writers according to the recommendation list. Please check with
the supplier about compatibility issues regarding unlisted DVD-R/RW drives.
•Assemble the duplicator according to your need.
•Make sure that the voltage setting is correct.
2.3 Completed duplication system
•Take the duplication system out of the package.
•Check the entire unit to see if there are any problems.
•Make sure that the voltage setting is correct.
•The hard drive is optional.
Hardware Connection of CoolCopyD1AL (DVD-Backup) without a HDD
CoolCopy1AL (CD-Backup)
DVD
-
ROM
DVD+/
-
RW
Power

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
6
Hardware Connection with Hard Drive for CoolCopyD3
When the system connects with the hard drive, the hard drive must connect on the IDE 0 port
with the “Master” setting and the DVD-ROM must set at “Slave”.
Hardware Connection without Hard Drive for CoolCopyD3
Coolcopy 3
IDE 0
DVD
-
Pow
er
IDE 3
DVD+/
-
RW
IDE 2
DVD+/
-
RW
IDE 1
DVD+/
-
RW
Coolcopy 3
IDE 3
DVD+/
-
RW
IDE 2
DVD+
/
-
RW
IDE 1
DVD+
/
-
RW
IDE 0
DVD
-
ROM
Pow
er

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
7
Hardware Connection with Hard Drive for CoolCopyD7
When the system has a hard drive connected, the hard drive must connect on IDE 0 port with
“Master” setting and the DVD-ROM must set at “Slave.”
Hardware Connection without Hard Drive for CoolCopyD7
Coolcopy 7
Coolcopy 7
IDE 4
DVD+RW
IDE 3
DVD+RW
IDE 2
DVD+RW
IDE 1
DVD
-
IDE 8
DVD+RW
IDE 7
DVD+RW
IDE 6
DVD+RW
IDE 5
DVD+RW
IDE
5
DVD+RW
IDE 1
DVD
-
IDE 8
DVD+RW
IDE 2
DVD+RW
IDE 7
DVD+RW
IDE 6
DVD+RW
IDE 3
DVD+RW
IDE 4
DVD+/
-
Pow
er
Pow
er

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
8
Chapter 3 Key Functions and Operating Instruction
1. LCD Display Panel: Display main functions and all messages.
2. Scroll up through menus or functions.
3. Scroll down through menus or functions.
4. Execute the function which you select.
5. Cancel the function which you select.
After turning the power on, the CoolCopyD DVD Duplicator will execute a self test for a few
seconds. After the self testing procedure runs, the LCD will show:
1. CoolCopyD3: CoolCopyD7:
2.
3.
4.
Two main operation procedures
If you install a 3.5” hard disc, the operation procedures is as the following screen shows:
1. With hard drive installed
•Once duplicator detects a hard disc, it will ask if you want to format or not. A 10GB hard
disc can be divided into 10 partitions.
•Use the Select Source to set the hard drive as the target source.
•Then select which partition to store the data in function 9 “Image.”
•If there is no data stored in partition, place a source DVD into DVD-ROM and use
function 9-01 Load to transmit data from DVD into selected partition by pressing ENT.
Different data can be stored in different partitions.
•Switch to function 1, Copy, by pressing the arrow button. Place blank DVD-R or DVD-RW
discs into the DVD writers. Press “ENT” button to start copying.
•When a Copy completes, the passed (correctly copied) DVD discs will be ejected
automatically. The default setting is for the discs to be ejected automatically, but this can
be changed.
CD Duplicator
1-3 ver: 1.10B
CD Duplicator
1-7 ver: 1.10T
Initialize SDRAM.....
Detect Drives.....
1. Copy

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
9
•Failed discs will remain in writers. The default setting is to keep failed discs in the writers,
but this can be changed. Press the buttons on the drivers to take the failed DVDs.
•During the duplication process do not press any button because interruption will harm the
device. DVDs will be damaged.
2. Without a hard drive installed
If you don’t install a 3.5” hard disc, the operation procedures will be as follows:
•Place the master disc in the DVD-ROM.
•Switch to function 1, Copy, by pressing arrow button. Place blank DVD-R or DVDRW
discs into all the DVD writers. Press ENT to start.
•When Copy completes, the passed DVDs will eject automatically. The default is to eject
automatically, but this can be changed.
• Failed DVDs will remain in the writers. The default is keeping failed DVDs in the writers,
but you can change it. You need to press the “eject” buttons on the writers to take the
failed DVDs.
ATA-66 Cable Layout:
Please identify the two different kinds of cable before the hardware installation.
Chapter 4 Function
4.1 Copy
Use this function to copy data from a source DVD directly onto blank DVD discs. Before copying
make sure that the source DVD is placed into DVD-ROM. If you have a HDD, make sure there is
data in your HDD partition. If you are not sure about the success of your duplication job, you can
use function 2 Test to simulate the copying process first.
Select function 1. Put a source DVD into DVD-ROM and blank DVD disks into DVD writers. DVD
rewriteable discs containing old data are usable, too.
LCD will show the process of copying
information as the following screen:
When copying is completed, the LCD will display as
the following screen:
Discs correctly copied will be ejected automatically
and failed ones will remain in the writers.
4.2 Test
Copying-24X 0%
650.0MB 74:00
1
.
Copy
OK: 03

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
10
Function 2 Test will simulate the copying process. When the simulation completes, the discs will
remain blank.
Press ENT button to start the disc simulation.
If you use DVD rewriteable discs that contain data, the old
Data will be quickly erased before simulation.
The LCD will show the testing
Information as the following screen:
.
When the process is finished, the LCD will
show the message as the following screen:
Stopping the test halfway does not affect the DVD discs. However, if the DVD rewriteable discs
contain important data, the information may be erased.
4.3 Test&Copy
Function 3 Test & Copy is to test first and then actually copy.
Select Function 3. Put a source DVD into DVD-ROM
and blank DVD discs into the writers.
Press ENT to start simulation. LCD will show the
information as the following screen:
After the tests finishes, actual copying will begin
as the following screen shows:
When the entire process finishes, the LCD will
show the information as the following screen:
4.4 Verify
Function 4, Verify, examines whether the target DVDs can be read correctly after copying.
Press ENT button to verify. The LCD will show as
the following screen:
The LCD will show verification information as
the following screen:
When the verification process is finished, the LCD
will display the result as such:
2.Test
Testing-24X 0%
650.0MB 74:00
2
.
Test
OK: 03
3.Test & Copy
Testing-24X 0%
650
.
0MB 74
:
00
Copying-24X 0%
650.0MB 74:00
3
.
Test & Copy
OK: 03
4.Verify
Verify--24X 0%
650.0MB 74:00
4
.
Verify
OK: 03

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
11
4.5 Compare
Function 5, Compare, allows you to make a comparison between the source and the target DVDs
after copying.
Select Function 5. Put the source DVD into DVD-
ROM and the target DVDs into DVD writers.
Press ENT to compare. LCD will show the
comparison information as the following screen:
When comparison completes, the LCD will show
as the following screen:
Press ENT to see the details of
source 1. If the comparison is identical, the LCD
will show the message as the following screen:
If the comparison result is identical, the LCD will
show as the following screen:
If comparison fails, the LCD will show failure.
Press ENT to see comparison
information.
If the comparison fails, the LCD will show
failure. By pressing ENT twice, the LCD will show
the contents of source 1 and those of source 2
do not match as the following screen:
4.6 Prescan
Use the prescan function to scan the source DVD for precise readability and also tests the
reading speed.
Select function 6. Put the source DVD
into the DVD-ROM.
Press ENT to prescan, LCD will show the
scanning information as the following screen:
If the master disc can be read correctly,
the source DVD will have no problems. The LCD
will show the following screen:
5
.
Compare
Compare-24X 0%
650.0MB 74:00
Compare OK
:
3
Fail: 0 Diff: 0
Src
:
01 CD-ROM
Total: 650.0MB
Src
:
02 DVD+RW
Identical
Compare OK
:
2
Fail: 1 Diff: 0
Src
:
01 CD-ROM
Total: 0 Bytes
Src
:
02 DVD+RW
TOC not match
6.Prescan
Scaning-24X 0%
650.0MB 74:00
PreScan OK!

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
12
If the master disc cannot be read correctly,
the LCD will show the following screen:
4.7 Disc Info
Function 7, Disc Info, shows the basic information of the source DVD.
Select Function 7. Place source DVD into DVD-ROM.
Press the ENT button to show the disc information.
The LCD will show the total sessions and
tracks on the master disc.
Press the ENT button again, the LCD will show
the total time and capacity on the master disc as such:
Press the ENT button again and use the arrow button
to select the session. The LCD will show the
information contained in the session as such:
Press the ENT button again and use the arrow button
to select the track. The LCD will show what
information is contained on the track.
4.8 Select Source
Function 8, Select Source, lets you select the data on the DVD-ROM, DVD writers or HDD as the
source from which you intend to copy.
Select function 8.
Press ENT and then use the arrow button to select
the source.
After selecting the source, press ENT and LCD will
show the following screen:
Note: Suppose you select HDD as the source and try to copy from one of its partitions, but the
partition contains no data. An error message will then appear on your LCD. From here, you can
switch to another partition that contains no data or use function 9 Image to load the data into the
chosen partition first.
4.9 Image
Function 9, Image, is only valid when you have installed a hard drive.
Select function 9. Press ENT.
PreScan Fail!
7.Disc Info
Total 02 Sessions
Total 10 Tracks
Total
:
74:00
Total: 650 MB
Session 01
Track 01 - 09
Track 01
AUDIO 03:54
8.Select Source
Src
:
CD-ROM
01 IDE0 Slave
CD-ROM selected!
9.Image

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
13
4.9.1 Load
Place the master DVD disc into the DVD-ROM or any one of the DVD writers, the duplicator
will detect and analyze the master DVD.
Here the function “Load” will allow you to load data
from the DVD-ROM or any DVD writer into the
current partition of the hard disc. P:A means Partition A.
Press ENT to load. The LCD will show the loading
information.
When the image has successfully loaded, the LCD
will show as the following screen:
If there is an image file existing in the current partition,
the system will ask whether you want to overwrite.
Use arrow button to make “Yes” or “No” selection.
4.9.2 Delete Image
If you want to empty an image file stored in a particular partition, you can use the function Delete
Image to do so.
Select function by pressing arrow.
The system will ask if you are sure you want to delete.
Use arrow button to make “Yes” or “No” selection.
When the image is successfully deleted from the
hard drive, the LCD will show the following message:
4.9.3 Image Info
This function shows the basic information of an image file stored in a particular partition.
Press ENT to show the disc information.
The LCD will show the total sessions and tracks
in the partition.
Press ENT again. The LCD will show
the total time and capacity in the hard drive of
partition.
9
-
01
.
Image P
:
A
Load
Load- A -24X 0%
650.0MB 74:00
Image load OK
Image Exists
Overwrite?Yes
9
-
02
.
Image P
:
A
Delete Image
Delete Image in
Partition A?Yes
Partition A:
Image is deleted
9
-
03
.
Image P
:
A
Image Info
Total 01 Sessions
Total 01 Tracks
Total
:
74:00
Total
:
650 MB

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
14
Press ENT again and use the arrow button
to select the session. The LCD will show the information
in the session.
Press ENT again and use arrow button to select
the track. The LCD will show track information.
4.9.4 Compare Image
Use this function to compare the contents of the source DVD and those of the image file in the
partition. First select the function by pressing the arrow.
Press ENT and LCD will show the comparison
information as such:
LCD will then show the following message:
When the process is finished, the LCD will display
the results as such:
Press ENT to view the comparison details.
If the comparison is identical, the LCD will
show the message as such:
If comparison fails, the LCD will show the number of discs
that have failed and succeeded.
Press ENT to see the comparison
information.
If the comparison fails, the LCD will show the
following message:
4.9.5 Select Partition
This function, select Partition, allows you to select a partition in the hard disc.
Press ENT button to change the setting.
After installing a hard disc, the duplicator will format it automatically. Each partition occupies 1GB.
The number of partitions is dependent on the hard disc’s capacity. The partitions are
alphabetically arranged.
Session 01
Track 01 - 01
Track 01
DATA 650.0MB
9
-
04
.
Image P
:
A
Compare Image
Comp-A-24X 0%
650.0MB 74:00
Compare OK
:
1
Fail
:
0 Diff
:
0
Src
:
01 CD-ROM
Total: 650.0MB
Tgt
:
00 HDD P:A
Identical
Compare OK
:
0
Fail: 1 Diff: 0
Src
:
01 CD-ROM
Total: 0 Bytes
Src
:
02 DVD+RW
TOC not match
9
-
05
.
Image P
:
A
Select Image

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
15
Use the arrow button to select which partition will
be worked.
When the partition is set, the LCD will show the
following screen:
4.9.6 Select Src Drive
This function allows you to select the DVD-ROM or any DVD writer as the source from which you
can load data into a particular partition as an image file.
Press ENT and the arrow button to select
the source.
Then use the arrow button to select the disc as the master
source.
After selecting the source, press ENT.
The LCD will show will show the following message:
4.10 Edit Track
Function 10 Edit Track allows you to edit a collection of favorite songs from CDs. You’re able to
collect different tracks or songs on a number of CDs and merge them onto a single CD. This
process can be divided up into four parts: CD to CD, CD to HDD, Play Audio Track and Close
Session.
Press ENT and use the arrow button to select function 10.
4.10.1 CD to CD Edit
Select “CD to CD Edit” to select one or more tracks from CD-ROMs and then copy onto blank
CD-R/RWs.
Press ENT to change setting.
Follow the LCD to select the track that you want
to edit.
Press ENT to select the track. After the
track is selected, the “+” will appear beside 1/10 as shown.
Pressing ENT again will cancel the track.
When the track selection is made, use the arrow button
to move to the End menu.
Select Working
Partition - A
Set Partition to
A
9
-
06
.
Image P
:
A
Image Src Drive
Select Img Src
:
01 IDE0 CD-ROM
Load image from
Drive ID-01
10
.
Edit Track
10-01
.
Edit Track
CD to CD Edit
Select Track
:
1/10 03:25
Select Track
:
+1/10 03:25
Select Track
:
End 1Trk03:25

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
16
Press ENT to finish the disc editing. Use the arrow button
to make “Yes” or “No” selection.
The LCD will then show the following screen:
When copying ends, the LCD will show the
following message:
The system will ask if you want to continue editing. Use
the arrow button to make a “Yes” or “No” selection
.
If “Yes” is selected, the source disc will be
automatically ejected. Insert another disc.
Follow the steps to select the track that you want
to edit. Then press ENT.
When the track selection is made, use the arrow button
to move to the “End” menu.
Press the ENT button to finish disc editing.
Use the arrow button to make a “Yes” or “No”
selection.
The LCD will show will show the following message:
The 2/2 symbolizes the second track of all tracks you have
selected. So far you have selected two tracks from two
different CDs.
When copying ends, the LCD will show the
following message:
System will ask you whether you want to continue editing.
Use the arrow button to make a “No” selection then press
ENT.
The system will ask to close the disc session.
Use the arrow button to make “Yes” or “No”
selection.
The LCD will show the closing session as such:
End edit disc
and burn?Yes
Copying- 24X Edit
1/10 - > 1/1
Burn Complete!
OK: 03
Continue edit
next Disc?Yes
Insert next disc
Select Track
:
+2/10 04:25
Select Track
:
End 2Trk07:50
End edit disc
and burn?Yes
Copying- 24X Edit
1/10 - > 2/2
Burn Complete!
OK: 03
Continue edit
next Disc?No
Close all disc’s
session? Yes
Closing Session
Please wait---

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
17
4.10.2 CD to HDD
This function lets you select one or more tracks from DVD-ROM and then copies into a certain
partition of the HDD.
Press ENT to enter the setting.
Follow the LCD to select the track that you want
to edit. Here 1/10 means the number one of 10 tracks
and 3:25 means the playing time.
Press ENT button to select the track. After the
track is selected, the “+” will appear. Pressing
ENT again will cancel the track.
When the track selection is made, use the arrow button to
move to the “End” menu.
Press ENT to finish the disc editing process. Use the arrow
button to make a “Yes” or “No” selection.
The source will be loaded to the hard drive. The LCD
will show the loading information as such:
When “Image Load” is finished, the LCD will
show the message as such:
The system will ask if you want to continue editing. Use the
arrow button to make a “Yes” or “No” selection.
If “Yes” is selected, the source disc will be automatically
ejected. Insert another disc.
Follow the steps to select the track that you want
to edit. Then press the ENT button.
When the track selection is made, use the arrow button
to move to the “End” menu.
Press the ENT button to finish disc editing. Use the arrow
button to make a “Yes” or “No” selection.
The track will be loaded as an image file to the hard drive.
LCD will show the following screen:
When loading is finished, the LCD will
show the following message:
The system will ask you whether you want to continue editing.
Use the arrow button to make a “Yes” or “No” selection. Select
“No” to go to the next step.
The system will ask you if you want to burn from HDD into
10-02
.
Edit Track
CD to HDD Edit
Select Track
:
1/10 03:25
Select Track
:
+1/10 03:25
Select Track
:
End 1Trk03:25
End edit disc
and burn?Yes
Load- P0 -24X Edit
1/10 - > 1/1
Image load OK
Continue edit
next Disc?Yes
Insert next disc
Select Track
:
+2/10 04:25
Select Track
:
End 2Trk07:50
End edit disc
and burn?Yes
Load- P0 -24X Edit
1/10 - > 2/2
Image load OK
Continue edit
next Disc?No

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
18
CD-R/RW or move into partition. Selecting “Burn” will
start the process.
The LCD will show the copying information as such:
When burning is finished, the LCD will show
the following screen:
Selecting Move will move the data from the hard
drive template to a certain partition.
Select the partition that the data will move into by
pressing the arrow.
The LCD will show the moving information as such
When moving is finished, the LCD will show
the following message:
If the chosen partition contains image data, the
system will ask to overwrite it. Select “No” to
keep the data image or “Yes” to overwrite it.
The LCD will show the moving information as such:
When moving is finished, the LCD will show the
message on the following screen:
4.10.3 Play Audio Track
This function allows your machine to be utilized as a music player. All you have to do is plug in an
AV terminal in the audio port on the back of the device.
Press ESC and the arrow button to enter the play audio
function.
Use the arrow button to select a track you
are going to play.
Press ENT and the LCD will display the playing information
as the following screen:
4.10.4 Close Session
Select “Close Session” will close the disc and restrict data writing. This function allows discs to be
read on any normal player.
Burn or Move to
Partition?Burn
Copy- P0 -24X 0%
1/2 Trk03
:
25
Burn Complete !
OK: 03
Burn or Move to
partition? Move
Select Partition
A
Moving to P: A
0%
Moving to P: A
OK!
Image Exists
Overwrite?Yes
Moving to P: A
0%
Moving to P: A
OK!
10-03
.
Edit Track
Play Audio Track
Select Track
:
1/10 03:25
Playing Track-1
00:00 / 03:25

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
19
Press ESC and the arrow to select the function.
Press ENT. The system will ask whether you want to
close. After this step, the data cannot be written onto the disc.
The LCD will show the message as the following screen:
When you are finished closing the session, the LCD will
show the following message:
4.11 Setup
This function allows you to change default settings. It is suggested that you use default setting for
optimal performance.
Press ENT button to enter the Setup function.
4.11.1 Language (optional)
Here are the available languages on the LCD: English, Traditional Chinese, Simplified Chinese
and Japanese.
Press ENT to change the setting and ESC to
exit.
4.11.2 CD Burn Speed
This setting controls the burning speed of CD writers. Default setting is “Auto,” which will use the
highest writing speed of the writers.
Press ENT to enter the setting.
Use arrow button to change the burning
speed then press ENT.
* The DVD Burn Speed lets you control the burning speed of DVD writers. Press ESC to enter
this function. Then press ENT to view the default setting, which is at maximum.
4.11.3 Read Speed
This function lets you control the reading speeds of target CDs.
Press ENT to enter the setting.
Use the arrow button to change the reading
10-04
.
Edit Track
Close Session
Close all disc’s
session? Yes
Closing Session
Please wait---
Closing
Complete
OK :3 Fail :0
11. Setup
11-01. Setup
Language
11-02. Setup
Burn Speed
Burn Speed
24X
11-03. Setup
Read Speed
Read Speed
32X

Copyright©2005 ILY Enterprise, Inc. All rights reserved.
20
speed then press ENT. The default is maximum. Other
choices are 32X, 16X and 8X.
4.11.4 Auto Start Drive
This function automatically tests or copies once you put the blanks discs into the writers.
Press the ENT button to enter Auto Start Drive.
Use the arrow button to change either the number or the
“Off” setting. Then press ENT or ESC to
go back to the 11-04 menu.
4.11.5 Start up menu
This setting lets you select any one of the functions, except Adv Setup, as the first item to appear
on the menu when you turn on your device.
Press ESC button to enter Startup Menu and
ENT to enter the following figure:
Use the arrow button to select other function setting, which would
be the first setting to appear when device is turned on.
Then press ENT.
4.11.6 Auto Verify
This setting allows you to automatically verify if target DVDs can be read after copying.
Press the ENT button to enter the following figure:
Use arrow button to change “On” or “Off”
setting. Then press ENT or press ESC to
return to the 11-06 menu.
4.11.7 Auto Compare
This setting allows you to automatically compare the source DVD
and target DVDs after copying. Press ESC button and arrow
to enter the setting.
Use the arrow button to change the “On” or “Off” setting.
Then press ENT to go back to the 11-07 menu.
11-04. Setup
Auto Start
Drive
Auto Start
Drive
Off
11-05. Setup
Startup Menu
Startup Menu
1.Copy
11-06. Setup
Auto Verify
Auto Verify
Off
11-07. Setup
Auto Compare
Auto Compare
Off