IMPRESIA 99 KM10 User manual

1
TECHNICAL SPECIFICATIONS
USER MANUAL FOR INSTALLATION, USE,
MAINTENANCE AND CONTROL OF THE EQUIPMENT
Company: IMPRESIA 99 LTD
Combined children play facility model KM10
I. TECHNICAL SPECIFICATIONS
1. General Characteristics
Model
KM10
Age group
3 - 12 y. o.
Maximum free fall height
150 cm
Types of games
Climbing, sliding, balancing
Admissible surfaces for the fall area
Grass, sand, shock-absorbing synthetic surface
Standards compliance
BS EN1176-1, BS EN1176-3, BS EN71-3.
Warranty period
24 months
The town of Provadiya
Tel.: [phone] Fax: [phone]
Mobile: [phone]
Email: imp[email protected]
www.impresia.net

2
2. Dimensions of the Equipment and Minimum Space for Placement
3. Materials Used
The structural elements are produced of selected dried softwood with the appropriate profile.
Their technical and operational characteristics correspond to the loads required during the
operation of the equipment. The equipment structure is designed in accordance with the
EN1176-1 requirements both in terms of the fixed and variable loads depending on the
number of users in the particular area, and in regards with all requirements of this standard
for protection against falls and protection against all types of clamps. The structure is
certified by Construction Declaration and in-house Test Reports. All parts are round, with a
radius of less than 3 mm, and are polished, impregnated and varnished with three layers of
environmentally-friendly acrylic varnish suitable for outdoor conditions (attested by a
varnish certificate). The joints are covered by galvanized metal threaded lining with
countersunk heads and cannot be disassembled without the use of a special tool. All other
metal parts and components of the equipment are protected against weather conditions by
non-toxic coatings.
The slides are made of multi-layer fibreglass resistant to UV rays and have the adequate
strength required for their use by children of the specific age group. They are smooth, easy
to be cleaned and have no sharp edges and protrusions. The slides are accompanied by the
required Declaration of Conformity prepared on the basis of the Test Report for compliance

3
with the requirements of BS EN 71-3 (“Safety of Toys - Migration of Certain Elements”)
issued by an accredited laboratory.
All modules of the equipment, which include cable components, are made of special multi-
wire rope with a diameter of 16 mm and suitable polyamide mesh. The rope is attached by
steel plating and aluminium press sleeves (Quality Certificate of the rope and plating issued
by the manufacturer).
The plywood used in the production features maintains the required water resistance and has
a three layer acrylic varnish coating with UV protection.
The structural elements are produced of steel pipes and plates with the appropriate profiles.
Their technical and operational characteristics correspond to the loads required during the
operation of the equipment. The equipment structure is designed in accordance with the
requirements of EN1176-1 both in terms of the fixed and variable loads depending on the
number of users in the certain area and in regards with all requirements of this standard for
protection against falls and all types of clamp. The structure is certified by a Construction
Declaration and in-house Test Reports. All parts are covered with a three layer corrosion
resistant primer and environmentally-friendly acrylic varnish suitable for outdoor conditions
(attested by a varnish certificate). The joints are covered by galvanized metal threaded
lining.
II. ASSEMBLY OF THE EQUIPMENT
The equipment should be mounted on the ground in accordance with the Construction Declaration
of the product through concrete foundations with the required dimensions or through anchoring to
the existing concrete slab with a thickness at least 10 cm, which is reinforced in the anchoring area.
III. GENERAL INSTRUCTIONS FOR MAINTENANCE OF THE EQUIPMENT
> According to BS EN 1176 and Ordinance № 1 of January 12th, 2009 on the Terms and
Conditions for Playgrounds Structure and Safety (State Gazette, issue 10/2009) the equipment is
subject to regular, periodic and annual monitoring.
- The regular monitoring is carried out by the owner of the playground once every 7 - 10
days in order to examine for any obvious dangers.
- The periodic monitoring is carried out by the owner of the playground once every 1 - 3
months depending on how often the playground is visited. The periodic monitoring is carried out
for the purpose of detailed examination of the functioning and stability of the play facilities due to
their wearing.
- The annual monitoring is carried out for the purpose of complete and detailed examination
of the overall level of safety on the playground, which should comply with the requirements of the
above-mentioned Ordinance.
> In case of any troubles, measures to eliminate the identified hazards and risks for the safe
operation of the playground should be taken.
…………………
For company: IMPRESIA 99 Ltd