IMPRESIA 99 T06-3 User manual

1
TECHNICAL SPECIFICATIONS
USER MANUAL FOR INSTALLATION, USE,
MAINTENANCE AND CONTROL OF THE EQUIPMENT
Company: IMPRESIA 99 LTD
Combined slide model T06-3
I. TECHNICAL SPECIFICATIONS
1. General Characteristics
Model
T06-3
Age group
2 –6 y. o.
Maximum free fall height
59 cm
Maximum number of users
2
Size of the facility
188 х 49 х 108 см
Safety zone
16 м2
Types of games
Climbing, sliding, themed games
Admissible surfaces for the fall area
Grass, sand, shock-absorbing synthetic surface,
wood chips
Standards compliance
BS EN1176-1, BS EN1176-3, BS EN71-3.
Warranty period
24 months
The town of Provadiya
Tel.: [phone] Fax: [phone]
Mobile: [phone]
Email: [e-mail]
www.impresia.net

2
2. Dimensions of the Equipment and Minimum Space for Placement
3. Materials Used
•The structural elements are produced of selected dried softwood with the appropriate profile.
Their technical and operational characteristics correspond to the loads required during the
operation of the equipment. The equipment structure is designed in accordance with the
EN1176-1 requirements both in terms of the fixed and variable loads depending on the
number of users in the particular area, and in regards with all requirements of this standard
for protection against falls and protection against all types of clamps. The structure is
certified by Construction Declaration and in-house Test Reports. All parts are round, with a
radius of less than 3 mm, and are polished, impregnated and varnished with three layers of
environmentally-friendly acrylic varnish suitable for outdoor conditions (attested by a
varnish certificate). The joints are covered by galvanized metal threaded lining with
countersunk heads and cannot be disassembled without the use of a special tool. All other

3
metal parts and components of the equipment are protected against weather conditions by
non-toxic coatings.
•The slides are made of multi-layer fibreglass resistant to UV rays and have the adequate
strength required for their use by children of the specific age group. They are smooth, easy
to be cleaned and have no sharp edges and protrusions. The slides are accompanied by the
required Declaration of Conformity prepared on the basis of the Test Report for compliance
with the requirements of BS EN 71-3 (“Safety of Toys - Migration of Certain Elements”)
issued by an accredited laboratory.
•The roofs of the children playhouses have wooden structure covered with OSB and bitumen
membrane with a colourful slate and corner edges made of wood and aluminium. They are
designed to withstand the required load of snow, wind and temperatures.
•All modules of the equipment, which include cable components, are made of special multi-
wire rope with a diameter of 16 mm and suitable polyamide mesh. The rope is attached by
steel plating and aluminium press sleeves (Quality Certificate of the rope and plating issued
by the manufacturer).
•The plywood used in the production features maintains the required water resistance and has
a three layer acrylic varnish coating with UV protection.
II. INSTRUCTION FOR INSTALLATION OF THE EQUIPMENT
The installation of the equipment to the existing terrain is performed as follows:
When installing on a reinforced concrete slab with a thickness of at least 10 cm (according
to the constructive opinion of the equipment), the installation is performed by certified segmented
anchors. After tightening the anchors, the protruding part is cut out and, after applying the impact
absorbing rubber covering, the entire anchoring zone is covered and aligned with the covering with
a special rubber jointing mixture.
When installing on а lawn or а terrain with bulk covering (sand or chips), attachment of the
equipment is performed by cement stabilization with concrete foundations according to the
foundation plan below. The connection of the structure and the concrete foundations is made by
metal pillars with welded reinforcement in the area of the foundation. Depending on the type of
equipment, these embedded items are a continuation of the supporting pillars (when the equipment
has a metal structure) or are a separate element connecting the wooden structure to the foundations.
In the case of bulk impact absorbing covering, the supporting metal pillars are stretched depending
on the thickness of the covering, so that the foundations can be casted into solid support soil. After
the installation of the equipment, the concrete foundations are covered with soil or bulk covering to
the level of the terrain.

4
III. OPERATING AND MAINTENANCE INSTRUCTION OF THE SLIDE EQUIPMENT
1. The commissioning of the installed equipment by cement stabilization with concrete
foundations shall be performed after the final maturing of the concrete (not less than 48 hours after
its washing).
2. The use of the equipment is unacceptable prior to providing the foreseen in the project
corresponding impact absorbing covering and the minimum fall and play area provided in this
Technical Specification.
3. In order to achieve a longer operating life, it is necessary to perform periodic maintenance
of the equipment.
- Despite the fact that the wood used for production is selected and dried, it is a natural
material that is expected to expand and collapse over time and it is therefore necessary in the
periodic checks described below to check the tightness of the bolt connections and in case of
necessity to be tightened.
- It is necessary to periodically clean the equipment from sand and other solid particles,
which accelerate the wear of the horizontal or sloping surfaces.
.
IV. GENERAL INSTRUCTIONS FOR MAINTENANCE OF THE EQUIPMENT
> According to BS EN 1176 and Ordinance № 1 of January 12th, 2009 on the Terms and
Conditions for Playgrounds Structure and Safety (State Gazette, issue 10/2009) the equipment is
subject to regular, periodic and annual monitoring.
- The regular monitoring is carried out by the owner of the playground once every 7 - 10
days in order to examine for any obvious dangers.

5
- The periodic monitoring is carried out by the owner of the playground once every 1 - 3
months depending on how often the playground is visited. The periodic monitoring is carried out
for the purpose of detailed examination of the functioning and stability of the play facilities due to
their wearing.
- The annual monitoring is carried out for the purpose of complete and detailed examination
of the overall level of safety on the playground, which should comply with the requirements of the
above-mentioned Ordinance.
> In case of any troubles, measures to eliminate the identified hazards and risks for the safe
operation of the playground should be taken.
V. GUARANTEE CARD
The warranty period of the product is 24 months from the date of installation.
The warranty period of the performed construction and assembly works - sanding with concrete
foundations or anchoring on a reinforced concrete slab is 5 years from the date of commissioning of
the site.
The operating period of the product is significantly longer than the warranty period and is largely
dependent on the periodic maintenance of the equipment described in the operating instructions and
the technical specification.
The warranty period covers the following defects:
- Defects of poor manufacturing quality of the product
- Defects of poor quality materials
- Defects due to poor installation
Product warranty does not apply in the following cases:
- If the product is assembled or installed in a manner contrary to the manufacturer's instructions
(when installed by the customer)
- Damages to the product caused by vandalism
- Damages caused by improper use not in accordance with the manufacturer's recommendations
stated in the operating instructions
- If the buyer has not performed the necessary checks and maintenance of the product in accordance
with the manufacturer's recommendations stated in the operating instructions
- In the case of normal wear and tear resulting from the use of the product for its intended purpose,
such as scratches, dents, abrasion, fading, cosmetic problems of surface corrosion, micro cracks in
wood not affecting the strength and safety of the product.
- Hidden defects in installation work in anchoring due to a poorly executed concrete foundation
(slab) by the client. Such a problem may occur with insufficient covering thickness or poor quality
concrete.
.....................
For company: “IMPRESIA 99” OOD