inbody InBodyBAND User manual

Instructions

Table of Contents
1. Product Components
2. External Features
3. Charging
4. Installing the BodyKey App
5. Powering Up
6. Syncing the InBodyBAND with the BodyKey App
7. Manual Mode
8. InBodyBAND Modes
1
2
3
4
6
8
10
12

9. Accurate Test Guidelines
10. Testing Precautions
11. InBody Test
12. Heart Rate Measurement
13. Data Management
14. General Precautions
15. Others
16. Specications
17. FCC Information
18. Telecommunication Logos
13
19
20
23
25
27
36
40
45
50

• Failure to comply with safety warnings and regulations can cause serious
injury or death.
Warning
• Failure to comply with safety cautions and regulations can cause injury or
property damage.
Caution
• Helpful information and useful tips that are handy while using the product.
Note

1
1. Product Components
❶ InBodyBAND
❷ Micro USB Cable
❸ Instructions
Instructions
❶
Instructions
❷
Instructions
❸

2
2. External Features
Finger electrodes
Button
LCD screen
Wrist electrodes
Micro USB port
Fastener

3
3. Charging
Charge the InBodyBAND prior to initial use.
• InBody Test, Heart rate cannot be measured while the InBodyBAND is
charging.
Note

4
4. Installing the BodyKey App
Connect this product with the BodyKey App to transfer
and monitor your data conveniently on your smartphone.
1) Search “BodyKey” in the Google Play Store or the Apple App Store.
2) Download the App.
3) Load the App and follow the instructions on-screen to sync this
product with your smartphone.

5
• This product is compatible with Android 4.3(Jellybean) with BLE or newer
and iPhone 4S/iOS7 or newer.
Note
4. Installing the BodyKey App

6
5. Powering Up
Turn on this product by holding the side button
down for 3 seconds.
The time will appear on-screen when the
product is on.

7
• This product cannot be turned off manually.
Display will turn off after 4 seconds of inactivity.
• If this product does not turn on, charge the product as instructed on page 3
until fully charged. Try turning on the product again. If the product still does not
turn on, please contact AMWAY™ Customer Service Team (page 52).
Note
5. Powering Up

8
6. Syncing the InBodyBAND with the
BodyKey App
Install the BodyKey App on your smartphone as instructed, and connect
the product to the App over Bluetooth.
1)
InBodyBAND: After charging adequately, press and hold the button
for 3 seconds to turn the power on.
2) BodyKey App: On the BodyKey App, go to Settings Devices
and select the InBodyBAND to bring up the setup screen.

9
6. Syncing the InBodyBAND with the BodyKey App
• You may experience difculties linking your InBodyBAND if there are other
InBodyBANDs present.
• The time on your InBodyBAND will automatically sync with your smartphone.
Note
3) BodyKey App: Tap the Settings button on the BodyKey App. In the
Bluetooth registration request window, tap the “OK” button and
proceed as instructed on the App.

10
7. Manual Mode
Time can be set manually if the BodyKey App is not utilised.
1. Turn on your InBodyBAND by holding the side button down for three
seconds.
2. Press the button to advance through the menu until the clock icon
shows on the screen. You will see the time.
3. Hold the button for 5 seconds to set Hours. The hours will ash.
4. Press the button to change the Hours.

11
• The InBody Test is not available if the InBodyBAND is not connected to
a smartphone.
Note
7. Manual Mode
5. Hold the side button again for 2 seconds to set Minutes.
The minutes will ash.
6. Press the button to change the Minutes.
7. Save the time by holding down the button for 3 seconds.

12
8. InBodyBAND Modes
Alternate through modes by pressing the side button.
Heart
Rate
Exercise
Duration
Distance
Covered
Battery
Life
Calories
Burned
Time InBody
Test Steps

13
9. Accurate Test Guidelines
If the InBodyBAND cannot come into full contact
with your wrist, fasten the band tighter or move
the band further down your arm until electrodes
are in full contact with skin.
The ideal testing position is to
wear the InBodyBAND directly
above your wristbone.

14
9. Accurate Test Guidelines
• For accurate measurement, electrodes must be in full contact with skin. In case
of poor contact between electrodes and skin, the test may not be proceeded or
test results may be inaccurate.
• To increase comparability between your results, place the InBodyBAND
on the same location on your wrist for every test.
• If skin is too dry, test may not be proceeded or test results may be inaccurate.
Please moisturise your skin before test.
Note

15
9. Accurate Test Guidelines
• In case where the user’s bioelectrical signal is weak, the test may fail, or the
results may be inaccurate.

16
Note
Stand upright for
5 minutes prior to testing.
Do not eat
prior to testing.
Use the restroom
prior to testing.
9. Accurate Test Guidelines