Indesit WI141 User manual

1
GB
English,1
Contents
Installation, 2-3-4-5
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 4
Technical details, 5
Washing machine description, 6-7
Control panel, 6
eds, 7
tarting and Programmes, 8
Briefly: how to start a programme, 8
Programme table, 8
Personalisations, 9
Setting the temperature, 9
Functions, 9
Detergents and laundry, 10
Detergent dispenser, 10
Preparing your laundry, 10
Special items, 10
Precautions and advice, 11
General safety, 11
Disposal, 11
Saving energy and respecting the environment, 11
Care and maintenance, 12
Cutting off the water or electricity supply, 12
Cleaning your appliance, 12
Cleaning the detergent dispenser, 12
Caring for your appliance door and drum, 12
Cleaning the pump, 12
Checking the water inlet hose, 12
Troubleshooting, 13
ervice, 14
Before calling for Assistance, 14
WA HING MACHINE
WI 141
Instructions for use
GB
All manuals and user guides at all-guides.com
all-guides.com

2
GB
Installation
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
3. Remove the four
protective screws and
the rubber bush with the
respective spacer,
situated on the rear of
the appliance (see also
the installation leaflet).
NB:The plastic spacers
may fall down inside the
machine once the bolt
has been removed, and will not interfere with the
operation of the machine.
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or
loosening the adjustable
front feet (see figure);
the angle of inclination,
measured according to
the worktop, must not
exceed 2°.
evelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe to the water mains,
fitting the rubber gasket
and the filter supplied with
the appliance and
ensuring that they are
fimly tightened to the
taps.
The water supply marked
C must be connected to
the cold water tap; the pipe marked H must be
connected to the hot water tap. Both pipes may be
connected to the cold water tap using the special Y
connection with multiple attachments, supplied with the
appliance (see figure).
Before making the connection, allow the water to run
freely until it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Ensure that the supply taps are allowing water
through. Old taps may seize in the closed position
and thus prevent water reaching the machine.
All manuals and user guides at all-guides.com

3
GB
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
The drain hose may be
connected to an
under-sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot.
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
 We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed down
too far, this may cause the machine to self -syphon
ie. continuously empty as it is filling.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
 the socket is earthed and in compliance with the
applicable law;
 the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
 the supply voltage is included within the values i
ndicated on the Technical details table
(see page 5);
 the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
WARNING - THIS APP IANCE MUST BE EARTHED.
THE FO OWING OPERATIONS SHOU D BE
CARRIED OUT BY A QUA IFIED E ECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
the plug is replaced by a fused 13 ampere re-
wearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with
BS 5733) which is accessible without moving the
appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured
in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
65 - 100 cm
Where it connects
to the waste water
pipe cut end off
spigot or remove the
blanking cap
All manuals and user guides at all-guides.com

4
GB
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
or or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described
above.
 The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
 When the washing machine is installed, the mains
socket must be within easy reach.
 Do not use extensions or multiple sockets.
 The power supply cable must never be bent or
dangerously compressed.
 The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
All manuals and user guides at all-guides.com

5
GB
Technical details
Model WI 141
Dimensions
59.5 cm wide
85 cm high
53.5 cm deep
Capacity from 1 to 5 kg
Electric
connections
voltage 230/240 Volts 50 Hz
maximum absorbed power 2050 W
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
pin speed up to 1400 rpm
Control
programmes
according to
IEC456 directive
programme 3; temperature 60°C;
run with a load of 5 kg.
This appliance is compliant with the
following European Community
Directives:
- 73/23/CEE of 19/02/73 ( ow
Voltage) and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
- 2002/96/CE
erviceTroubleshootingPrecautions CareProgrammes DetergentsDescriptionInstallation
All manuals and user guides at all-guides.com

6
GB
Washing machine description
Control panel
Detergent dispenser
ON-OFF
Button
TEMPERATURE
Knob
PROGRAMME
Knob
FUNCTION
Buttons
Detergent dispenser: to add detergent and fabric
softener (see page 10).
FUNCTION buttons: to select the functions
available.
TEMPERATURE knob: to set the temperature or
the cold wash cycle (see page 9).
ON/OFF button, to turn the washing machine on
and off.
Turning the machine off does not cancel the
selected programme.
ON/OFF led, to find out whether the washing
machine is on and if the programme set has been
accepted (see page 7).
PROGRAMME knob: to select the wash
programmes.
Note: After the wash cycle has been set and
accepted by the washing machine, any changes to
the position of the knob will be of no use (except in
the Stop/Reset position).
Turn this knob clockwise only.
ON-OFF
ed
All manuals and user guides at all-guides.com
all-guides.com

7
GB
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Leds
The EDS provide important information.
This is what they can tell you:
ON-OFF Led
ed flashes when the appliance is switched on and
awaiting a programme to be set. A steady light
means the appliance has accepted the selected
programme.
All manuals and user guides at all-guides.com

8
GB
tarting and Programmes
Programme table
Notes
For the description of the Anti-crease function, please see page 9. The information contained in the table is purely
indicative.
pecial programmes
Dail wash (programme 9 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30
minutes and allows you to save on both time and energy. By setting this programme (9 at 30°C), you can wash different fabrics
together (except for woollen and silk items), with a maximum load of 3 kg. We recommend the use of liquid detergent.
A class at 40°, the washing machine has a special programme to allow you to obtain optimum results even at low
temperatures. By setting programme 4 at a temperature of 40° C, the results you will obtain will be the same as you
would normally obtain at 60°C thanks to the washing machines action and the length of the wash cycle.
Briefly: starting a programme
1. Set the desired programme.
2. Set the wash temperature (see page 9).
3. oad your laundry into the appliance and shut the door.
4. Add the detergent and any fabric softener (see page 10).
5. Turn the appliance on by pressing button . The
ON/OFF led begins to flash, after 5 seconds, the
setting is accepted, the led stops flashing (staying
on) and the wash cycle begins.
6. To cancel the cycle set, select one of the symbols
(Stop/Reset) and wait 5 seconds: when the
cancellation has been accepted, the ON/OFF led
flashes, and you can turn the appliance off and
set a new cycle.
Note: if you wish to set a programmed start, see page 5.
7. When the programme is completed, the DOOR
OCK led will turn off to indicate that the
appliance door can be opened.
Turn the washing machine off by pressing button .
Take out your laundry and leave the appliance
door ajar to allow the drum to dry thoroughly.
Type of fabric and
degree of soil Progr. Te m p e - rature
Detergent Fabric
softener
Cycle
length
(minutes
Max.
Spin
Speeds
(r.p .m .
Description of wash cycle
pre-
wash wash
Cotton
Extremely soiled whites
(sheets, tablecloths, etc.) 190°C    135 Max. Pre-wash, wash cycle, rinse cycles, intermediate and final spin cycles
Extremely soiled whites
(sheets, tablecloths, etc.) 290°C   125 Max. Wash cycle, rinse cycles, intermediate and
final spin cycles
Heavily soiled whites and fast
colours 360°C   110 Max. Wash cycle, rinse cycles, intermediate and
final spin cycles
Heavily soiled whites and fast
colours 440°C   140 Max. Wash cycle, rinse cycles, intermediate and
final spin cycles
Slightly soiled whites and delicate
colours (shirts, jumpers, etc.) 540°C   70 Max. Wash cycle, rinse cycles, intermediate and
final spin cycles
Rinse cycles  Max. Rinse cycles, intermediate and final spin
cycles
Spin cycle Max. Draining and final spin cycle
Stop/Reset -Interrupts/Cancels the selected programme
ynthetics
Heavily soiled fast colour synthetics
(baby linen, etc.) 660°C   75 800 Wash cycle, rinse cycles, anti-crease or delicate spin cycle
Heavily soiled fast colour synthetics
(baby linen, etc.) 750°C   70 800 Wash cycle, rinse cycles, anti-crease or
delicate spin cycle
Delicate colour synthetics
(all types of slightly soiled garments) 840°C   60 800 Wash cycle, rinse cycles, anti-crease or
delicate spin cycle
Delicate colour synthetics
(all types of slightly soiled garments) 930°C   30 800 Wash cycle, rinse cycles and delicate spin
cycle
Rinse cycles  800 Rinse cycles, anti-crease or delicate spin cycle
Fabric Softener  800 Rinse cycles with automatic introduction of
softener, anti-crease or delicate spin cycle
Spin cycle 800 Draining and delicate spin cycle
Stop/Reset -Interrupts/Cancels the selected programme
Delicates
Wool (Hand wash)10 40°C   50 600 Wash cycle, rinse cycles, anti-crease and
delicate spin cycle
Particularly delicate garments and
fabrics (curtains, silk, viscose, etc.) 11 30°C   45 no Wash cycle, rinse cycles, anti-crease or
draining
Rinse cycles  600 Rinse cycles, anti-crease or draining
Spin cycle 600 Draining and delicate spin cycle
Drain no Drain
Stop/Reset -Interrupts/Cancels the selected programme
All manuals and user guides at all-guides.com

9
GB
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Personalisations
etting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8).
The temperature can be lowered, or even set to a cold wash ( ).
Functions
To enable the functions, press the button corresponding to the desired function, according to the table below:
Function Effect Comments
Rapid
wash
Cuts the duration of the wash
cycle by 30%.
Anti
crease
This function allows you to
interrupt a programme (on
symbol ) keeping the
washing soaking in water
before the spin cycle. It is a very
useful button in particular
because it can be used for
delicates and synthetics. It is
only to be used with wash
programmes for synthetic
fabrics, silk and curtains when
it is impossible for you to take
the washing out immediately.
Before opening the washing machine door, finish the wash cycle
as follows:
Silk and curtains: press button Anticrease and the washing
machine will drain the water.
S nthetic fabrics: press button Anticrease if you want a spin
cycle, or turn knob PROGRAMME to symbol if you want the
water to be drained.
With Dail wash programme, this function is not enabled.
 The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the final spin
speed if an unbalanced load is detected.
All manuals and user guides at all-guides.com

10
GB
Detergent dispenser
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
(powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
iquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
 Do not use hand wash detergent because it may
form too much foam.
Preparing your laundry
 Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
 Empty all pockets and check for loose buttons.
 Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
pecial items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme
11 which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Trainers: remove any mud. They can be washed
together with jeans and other tough garments, but
not with whites.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1 kg.
Detergents and laundry
123
All manuals and user guides at all-guides.com