Indesit WIXL 123 S User manual

1
GB
English, 1
Contents
Installation, 2-3-4-5
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 4
Technical details, 5
Washing machine description, 6-7
Control panel, 6
eds, 7
tarting and Programmes, 8
Briefly: how to start a programme, 8
Programme table, 8
Personalisations, 9
Setting the temperature, 9
Functions, 9
Detergents and laundry, 10
Detergent dispenser, 10
Bleach cycle, 10
Preparing your laundry, 10
Special items, 10
Precautions and advice, 11
General safety, 11
Disposal, 11
Saving energy and respecting the environment, 11
Care and maintenance, 12
Cutting off the water or electricity supply, 12
Cleaning your appliance, 12
Cleaning the detergent dispenser, 12
Caring for your appliance door and drum, 12
Cleaning the pump, 12
Checking the water inlet hose, 12
Troubleshooting, 13
ervice and Guarantee, 14-15-16
Before calling for Assistance, 14
Guarantee, 15-16
WA HING MACHINE
WIXL 123
Instructions for use
GB

2
GB
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
3. Remove the 3
protective screws and
the rubber bush with the
respective spacer,
situated on the rear of
the appliance (see also
the installation leaflet).
NB:The plastic spacers
may fall down inside the
machine once the bolt
has been removed, and will not interfere with the
operation of the machine.
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
Your machine may make a considerable amount of noise
if the two front feet have not been adjusted correctly.
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or
loosening the adjustable
front feet (see figure);
the angle of inclination,
measured according to
the worktop, must not
exceed 2°.
evelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose
and screw the latter
onto a cold water tap
with a 3/4 gas threaded
mouth (see figure).
Before making the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance (see
figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Ensure that the supply taps are allowing water
through. Old taps may seize in the closed position
and thus prevent water reaching the machine.
Installation
A

3
GB
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
The drain hose may be
connected to an
under-sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot.
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
 We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed down
too far, this may cause the machine to self -syphon
ie. continuously empty as it is filling.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
 the socket is earthed and in compliance with the
applicable law;
 the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
 the supply voltage is included within the values i
ndicated on the Technical details table
(see page 5);
 the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
WARNING - THIS APP IANCE MUST BE EARTHED.
THE FO OWING OPERATIONS SHOU D BE
CARRIED OUT BY A QUA IFIED E ECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
the plug is replaced by a fused 13 ampere re-
wearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with
BS 5733) which is accessible without moving the
appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured
in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
65 - 100 cm
Where it connects
to the waste water
pipe cut end off
spigot or remove the
blanking cap

4
GB
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
or or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described
above.
 The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
 When the washing machine is installed, the mains
socket must be within easy reach.
 Do not use extensions or multiple sockets.
 The power supply cable must never be bent or
dangerously compressed.
 The power supply cable must only be replaced by
an authorised serviceman.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.

5
GB
Technical details
Model WIX 123
Dimensions
59.5 cm wide
85 cm high
52.5 cm deep
Capacity from 1 to 6 kg
Electric
connections
please refer to the technical data plate
fixed to the machine
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
pin speed up to 1200 rpm
Control
programmes
according to
EN 60456
directive
programme 2; temperature 60°C;
run with a load of 6 kg.
This appliance is compliant with the
following European Community
Directives:
- 73/23/CEE of 19/02/73 ( ow
Voltage) and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
- 2002/96/CE
erviceTroubleshootingPrecautions CareProgrammes DetergentsDescriptionInstallation

6
GB
Washing machine description
Control panel
Detergent dispenser
ON-OFF
Button
TART/RE ET
Button
TEMPERATURE
Knob
PROGRAMME
Knob
Leds
FUNCTION
Buttons
ON-OFF/
DOOR
LOCK
ed
Detergent dispenser: to add detergent and fabric
softener (see page 10).
LED : to find out the wash cycle progress.
If the Delay Timer function has been set, the time
left until the programme starts will be indicated (see
page 7).
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
TEMPERATURE knob: to set the temperature or
the cold wash cycle (see page 9).
TART/RE ET button: to start the programmes or
cancel any incorrect settings.
ON-OFF/DOOR LOCK ed: to find out whether the
washing machine is on and if the appliance door can
be opened (see page 7).
ON/OFF button: to turn the washing machine on
and off.
PROGRAMME knob: to select the wash
programmes. The knob stays still during the cycle.

7
GB
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
ON-OFF/DOOR LOCK led:
If this ED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the ED to flash before you open the appliance door.
 The rapid flashing of the ON-OFF/DOOR OCK ed together with the flashing of at least one other ED
indicates there is an abnormality (see page 13).
Cycle progress:
During the wash cycle, the EDs gradually illuminate
on to indicate the cycle progress:
Prewash
Wash
Rinse
Spin cycle
Note: during draining, the ED corresponding to
the Spin cycle phase will be turned on.
Function buttons
The FUNCTION BUTTONS also act like EDS.
When a function is selected, the corresponding
button is illuminated.
If the function selected is incompatible with the
programme set, the button will flash and the
function will not be enabled.
If you set a function that is incompatible with
another function you selected previously, only the
last one selected will be enabled.
Leds
The EDS provide important information.
This is what they can tell you:
Delay set:
If the Delay Timer function has been enabled (see
page. 9), once you have started the programme,
the ED corresponding to the delay set will begin to
flash:
As time passes, the remaining delay will be
displayed, and the corresponding ED will flash:
Once the set delay is complete, the flashing ED will
turn off and the programme set will start.

8
GB
Type of fabric and
degree of soil Program mes Te m p e - rature
Detergent Fabric
softener
Stain removal
option/bleach
ycle
length
(m inute s)
Description of wash cycle
pre-
wash wash
tandard
otton: Extremely soiled whites
(sheets, tablecloths, etc.) 190°C    180 Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
otton: Extremely soiled whites
(sheets, tablecloths, etc.) 290°C   Delicate/
Traditional 165 Wash cycle, rinse cycles,
intermediate and final spin cycles
otton: Heavily soiled whites
and fast colours 260°C   Delicate/
Traditional 150 Wash cycle, rinse cycles,
intermediate and final spin cycles
otton: Heavily soiled whites
and delicate colours 240°C   Delicate/
Traditional 105 Wash cycle, rinse cycles,
intermediate and final spin cycles
otton: Slightly soiled whites
and delicate colours (shirts,
jumpers, etc.) 340°C   Delicate/
Traditional 70 Wash cycle, rinse cycles,
intermediate and final spin cycles
Synthetics: Heavily soiled fast
colours (baby linen, etc.) 450°C   Delicate 70 Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Synthetics: Heavily soiled fast
colours (baby linen, etc.) 440°C   Delicate 60 Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Synthetics: Delicate colours (all
types of slightly soiled garments) 540°C   Delicate 60 Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Wool 640°C   50 Wash cycle, rinse cycle,
delicate spin cycle
Very delicate fabrics
(curtains, silk, viscose, etc.) 730°C   45 Wash cycle, rinse cycles, anti-
crease or draining cycle
Time 4 you
otton: Heavily soiled whites
and fast colours 860°C   60 Wash cycle, rinse cycles,
intermediate and final spin cycles
otton: Slightly soiled whites
and delicate colours (shirts,
jumpers, etc.) 940°C   50 Wash cycle, rinse cycles,
intermediate and final spin cycles
Synthetics: Delicate colours (all
types of slightly soiled garments) 10 40°C  40 Wash cycle, rinse cycles,
delicate spin cycle
Synthetics: Delicate colours (all
types of slightly soiled garments) 11 30°C   30 Wash cycle, rinse cycles and
delicate spin cycle
port
Sports shoes (MAX. 2 pairs) 12 30°C  50
Cold wash (without detergents),
wash cycle, rinse cycles, and
delicate spin cycle
Fabrics for sportswear
(Tracksuits, shorts, etc.) 13 30°C   60 Wash cycle, rinse cycles,
intermediate and final spin cycles
PARTIAL PROGRAMME
Rinse Delicate/
Traditional Rinse cycles and spin cycle
Spin cycle Draining and spin cycle
Drain Draining
tarting and Programmes
Programme table
Notes
-For programmes 8 and 9, we advise against exceeding a wash load of 3.5 kg.
-For programme 13 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
pecial programme
Dail (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
Briefly: starting a programme
1. Switch the washing machine on by pressing button .
All the EDS will light up for a few seconds and
the ON-OFF/DOOR OCK ed will begin to flash.
2. oad your laundry into the washing machine and
shut the appliance door.
3. Set the PROGRAMME knob to the programme
required.
4. Set the wash temperature (see page 9).
5. Add the detergent and any fabric softener (see page 10).
6. Start the programme by pressing the START/RESET
button for one second. Once the programme has
been accepted all of the option and status ED's
will illuminate momentarily, the Door ock ED
will be lit and the relevant wash cycle progress
ED will also be lit.
To cancel it, keep the START/RESET button pressed
for at least 2 seconds.
7. When the programme is finished, the ON-OFF/
DOOR OCK ed will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the washing
machine off by pressing button .

9
GB
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Personalisations
C
etting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8).
The temperature can be lowered, or even set to a cold wash ( ).
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
Function Effect omments Enabled with
programmes:
Delay Timer
Delays the start
of the wash by
up to 9 hours.
Press the button repeatedly until the ED corresponding to the
desired delay is turned on.
The fifth time the button is pressed, the function will be disabled.
N.B.: Once you have pressed the Start/Reset button, the delay
can only be decreased if you wish to modify it.
All
Stain
removal
Bleaching cycle
designed to
remove the
toughest stains.
Please remember to pour the bleach into extra compartment 4
(see page 10).
This function is incompatible with the EASY IRON function.
2, 3, 4, 5,
Rinse cycle.
Easy iron
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
When this function is set, programmes 4, 5, 7 will end with the
laundry left to soak (Anti-crease) and the Rinse cycle phase ED
will flash.
- to conclude the cycle, press the START/RESET button;
- to run the draining cycle alone, set the knob to the relative
symbol and press the START/RESET button.
This function is incompatible with the STAIN REMOVA function.
3, 4, 5, 7, 8,
9, 10, Rinse
cycle.
Extra Rinse
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, 3, 4, 5,
8, 9, 10, 12,
13, Rinse
cycle.
 The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the
final spin speed if an unbalanced load is detected.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.

10
GB
Detergent dispenser
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
(powder)
Before pouring in the detergent, make sure that
extra compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
iquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
extra compartment 4: Bleach
 Do not use hand wash detergent because it may
form too much foam.
Bleach cycle
 Traditional bleach should be used on sturdy
white fabrics, and delicate bleach for coloured
fabrics, synthetics and for wool.
Place extra
compartment 4,
provided, into
compartment 1.
When pouring in the
bleach, be careful not to
exceed the "max" level
indicated on the central
pivot (see figure).
To run the bleach cycle alone, pour the bleach into
extra compartment 4, set the Rinse programme
and enable the Stain removal option (see page 9).
To bleach during a wash cycle, pour in the detergent
and fabric softener, set the desired programme and
enable the Stain removal option (see page 9).
The use of extra compartment 4 excludes the
possibility of using the pre-wash cycle.
Preparing your laundry
 Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
 Empty all pockets and check for loose buttons.
 Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 6 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1,5 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
pecial items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 7
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1,5 kg.
Detergents and laundry
123
4

11
GB
Precautions and advice
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
 The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
General safety
 This appliance has been designed for non-
professional, household use and its functions must
not be changed.
 This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
 Never touch the washing machine when barefoot
or with wet or damp hands or feet.
 Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
 Do not open the detergent dispenser while the
appliance is in operation.
 Do not touch the drain water as it could reach
very high temperatures.
 Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
 In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
 Always keep children well away from the
appliance while in operation.
 The appliance door tends to get quite hot during
the wash cycle.
 Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
 Before loading your laundry into the washing
machine, make sure the drum is empty.
Disposal
 Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
 The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal
waste stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the
environment. The crossed out "wheeled bin"
symbol on the product reminds you of your
obligation, that when you dispose of the appliance
it must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
aving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Indesit
technology, your washing machine only needs less
than half the amount of water to get the best
results: an objective reached to respect the
environment.
aving on detergent, water, energy and time
 To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
 The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
 Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
 Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
 If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 9) helps to
organise your wash cycles accordingly.
 If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.

12
GB
Care and maintenance
Cutting off the water or electricity
supply
 Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
 Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for your appliance door and
drum
 Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
 Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
washing machine (see
figure);
2. unscrew the lid
rotating it anti-
clockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
 Never use hoses that have already been used.

13
GB
Troubleshooting
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Your washing machine could fail to work. Before calling for Assistance (see page 14), make sure the problem
can't easily be solved by consulting the following list.
Problem
The washing machine won't
start.
The washing machine does not
fill with water.
The machine continuously fills
and empties with water.
The washing machine does not
drain or spin.
The washing machine vibrates
too much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same
time as at least one other LED.
There is too much foam.
Possible causes/ olution:
 The appliance is not plugged into the socket, or not enough to make contact.
 There has been a power failure.
 The appliance door is not shut properly.
 The button has not been pressed.
 The START/RESET button has not been pressed.
NB: It should be held minimum one second.
 The water tap is not turned on.
 A delayed start has been set (using the Delay Timer, see page 9).
 The water inlet hose is not connected to the tap.
 The hose is bent.
 The water tap is not turned on.
 There is a water shortage.
 The water pressure is insufficient.
 The START/RESET button has not been pressed.
 The drain hose is too low or too far in to the stand pipe (see page 3)
for correct installation.
 The wall drainage system doesn't have a standard pipe (min. 38 mm).
 Some programs have a slower final spin to taked best care of the
fabrics. See page 8 for details of the final spin speed for each program.
 The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 8).
 The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 9).
 The drain hose is bent (see page 3).
 Remove the drain hose from the standpipe or under-sink trap and check for
blockages, ensuring that the water can drain freely away from the machine.
 When the machine is installed, the locking screws for the oscillating
assembly are still in place. Remove the screws (see page 2).
 The washing machine is not level (see page 2).
 The washing machine is closed in between furniture cabinets and the wall (see page 2).
 The water inlet hose is not screwed on correctly (see page 2).
 The detergent dispenser is obstructed (to clean it, see page 12).
 The drain hose is not secured properly (see page 3).
 This means there is a problem with the machine. Before calling
Assistance, please follow the set of instructions below:
1. Switch off the machine;
2. Remove the plug connecting the appliance to the mains supply
and wait for at least 40 seconds;
3. Place the plug back into the socket;
4. Switch on the machine;
5. If the problem is still evident after this process has been carried out,
contact Assistance.
 The detergent is not suitable for machine washing (it should bear the
definition "for washing machines" or "hand and machine wash", or the like).
 You used too much detergent.

14
GB
Before calling for Assistance:
Check whether you can solve the problem on your own (see page 13);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
If the machine has been installed or used incorrectly, you may be charged for the maintenance callout service.
Always request the assistance of authorised servicemen.
Notify the operator of:
 the type of problem;
 the appliance model (Mod.);
 the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
ervice

15
GB
erviceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-The appliance is used only on the electricity or gas supply printed on the rating plate.
-The appliance has been used for normal domestic purposes only.
-The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-Any repair work must be undertaken by us or our appointed agent.
-Any parts removed during repair work or any appliance that is replaced become our property.
-The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
-Replacement of any consumable item or accessory . These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
-Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WI NOT APP Y IF THE APP IANCE HAS BEEN USED IN COMMERCIA OR
NON-DOMESTIC PREMISES.
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on
08709 088 088 (ROI 01 230 0233).
Free Helpdesk ervice
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any
technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08709 066 066
(ROI 0818 313 413)for telephone assistance, or, where necessary, to arrange for an engineer to call.
Guarantee

16
GB
195062665.01
04/2007 - Xerox Business Services
After ales ervice
No one is better placed to care for your Indesit appliance during the course of its working life than us - the
manufacturer.
Essential Contact Information
Indesit ervice
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified
engineers on call to ensure you receive fast, reliable, local service.
UK: 08709 066 066
Republic of Ireland: 0818 313 413
www.indesitservice.co.uk
Please note: Our advisors will require the following information:
Model number:
erial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean
your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08709 077 077
Republic of Ireland: 0818 313 413
www.indesitservice.co.uk
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling & Disposal Information
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality,
recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door,
plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the
appliance can no longer be plugged into a mains socket, and the door cannot be locked shut.