Indoor Sky Dayliter User manual

INSTALLATION INSTRUCTIONS
** Please read entire installation instructions before installing the Product
SuggeSted toolS
drill
level
Pencil
screwdriver
taPe Measure
Williamsport, Pa 17701 www.indoor-sky.com 570.651.5105
l-series dayliter shade
Page 1

Williamsport, Pa 17701 www.indoor-sky.com 570.651.5105
1. Mounting optionS & inforMation
inside Mount – Dayliter Shade is mounted to the structural jamb inside the window opening
front Mount – Dayliter Shade is mounted to the face of the window frame or front of the window mullion
side Mount – Dayliter Shade is mounted to the inside of the window frame, or mullion, using the side mount holes
NOTE:
Mounting screws provided are suitable for most mounting surfaces (Please see below for additional notes)
Wallboard or Plaster – Use hollow wall anchors for added support
concrete, stone, brick, or tile – Use appropriate drill bit and anchors before fastening the screws
Metal surfaces – Pre-Drill holes before fastening the screws
Page 2
right
inSide/front Mount
Side Mount
right
left
left

using the teMPlate Provided – Mark the location of the holes to be drilled for the mounting brackets
attach brackets – Using supplied hardware – Use level to ensure brackets are vertical before tightening
iMportant:
toensure the shade oPerates correctly – Make sure the head of the window opening is relatively straight and level prior to using the template
– itiS critical that the bracketS are level
Williamsport, Pa 17701 www.indoor-sky.com 570.651.5105
2. Mounting bracket location
NOTE: Template should be positioned on the mullions for
front mount
Page 3

Williamsport, Pa 17701 www.indoor-sky.com 570.651.5105
3. inStall upper lightShelf
install wall brackets Provided and snap pin end into the hole on one side and then guide the other pin end into the opposite hole
(Start with uppermost lightshelf and work down)
ensure lightshelves oPen and close freely and will not hit the window frame or mullion
4. inStall lower lightShelf
insert square drive Pin into square receiver in worm gear
with Pin end dePressed slide square opening, in light shlef, over drive pin
(this may take some maneuvering of the light shelf to get it into a position to slide together)
When drive Pin is fully engaged – snaP Pin end into hole in bracket
rightleft
NOTE: Bracket on Worm Gear side to be installed with ange away from jamb - Bracket on Pin End side to be installed normally, ange to jamb
Page 4

Williamsport, Pa 17701 www.indoor-sky.com 570.651.5105
5. inStall lightShelf connectorS
attach connector to both ends of uPPer lightshelf by inserting cable into End Stop, and locking the End Stop in position, then insert pin
into Lightshelf and lock into postion with E-Clip
ensure lightshelves oPen and close freely
+
-
using alevel check that the Lightshelves are in a
position parallel to the oor, and to each other
(If necessary adjust length of connector by rotating the
center piece of the connector)
Page 5

Williamsport, Pa 17701 www.indoor-sky.com 570.651.5105
attach safety chain hold to either Frame or Jamb – Ensure roller shade operates freely using chain operator
install oPtional chain stoPs with shade in closed position (all the way down) – Prevents shade tube from being exposed by over rotation
6. inStall roller Shade
with shade rolled all the way uP – The pin end snaps into the hole on right side then the clutch slots are inserted on the left
(or vice versa, depending on clutch installation)
– The clutch should be installed on the side best suited to the room layout (or user preference)
7. roller clutch – chain inStallation
Page 6

Williamsport, Pa 17701 www.indoor-sky.com 570.651.5105
8. folding crank inStallation
slide universal end of folding crank in the input shaft – connect using safety clip
attach folding crank retention cliP to jamb with screws provided so that crank will hang straight and snap into clip
9. faScia inStallation
snaP fascia in Place on brackets by inserting top edge and rotating bottom until it snaps in place
note:
Make Sure crank and worM gear operate freely and light Shelf rotateS open and cloSed freely
Page 7

Williamsport, Pa 17701 www.indoor-sky.com 570.651.5105
Single Shade application
Multiple Shade application
Page 8