InelControl YYGL35PRIC-10 User manual

P. I. E. INEL Sp. z o. o., ul. Mostowa 1, 80-778 Gdańsk, [email protected] www.inel.gda.pl
Tubular motor with built-in radio receiver with a return channel and overload detection function
Installation and operation manual
YYGL35PRIC-10/17
YYGL45PRIC-20/15
A tubular motor is an InelControl system device for
automatic operation of roller blinds.
The tubular motor features an obstacle detection and
automatic limit position setting functions.
The device includes a radio receiver with return channel.
The data sent over the return channel provide full control of
the device.
Use rigid links and stops in the bottom strip to ensure
correct operation of the tubular motor. The stops must be
installed as close to the guides as possible to ensure
correct operation. A window sill must be installed and the
roller blind curtain length must correspond to the length of
the guides.
1 Safety guidelines
General guidelines
The tubular motor with overload detection is configured by
default to guarantee safe installation and operation, provided
that all guidelines and the relevant safety and accident
prevention regulations are followed.
Installation and repairs must be carried out by a trained and
qualified professional. Do not modify or change the tubular motor
in any way. All warranty repairs must be carried out by the
manufacturer. Use genuine spare parts and accessories only.
The operational safety of the tubular motor can only be
guaranteed if the device is used as intended. The limit values
provided in the specifications must not be exceeded under any
circumstances.
Additional safety regulations
Follow the relevant safety and accident prevention regulations
when installing, commissioning and maintaining the tubular
motor. In particular, observe the following:
1. Fire safety regulations.
2. Accident prevention regulations.
General information on hazards and safety
measures
The following are the general guidelines for use of INEL devices
with other external devices. Follow the guidelines when installing
and operating these devices.
Caution - Failure to take precautions may result in
damage to the tubular motor, roller blind, roller
blind box, facade etc.:
• Check if all screw connections are secure before installing the
tubular motor with radio receiver and setting the limit positions.
Danger - Failure to take precautions may
result in injury or death.
• Check if the local voltage supply parameters correspond to the
device specification.
• Follow the relevant safety and accident prevention regulations.
• Use a circuit breaker for safe power supply disconnection (e.g.
fuse cut-off switch) for all connections.
• Check the power wires and cables regularly for damaged
insulation and continuity.
• Switch off the power supply before replacing damaged cables.
Warning
• Do not let children play with the control devices.
• Keep the control devices out of reach of children.
• Observe the roller blind in motion at all times and keep other
people away until it is fully opened or closed;
• Provide training and instructions for the users on device
operation and related risks. The operator is deemed to have
been trained if the employer, administrator or owner of the
device have instructed and authorised the operator to operate
the device.
2 Installation manual
2.1 Safety
▪The device must be installed by qualified personnel only.
▪The weight of the roller blind must not exceed the maximum
load carrying capacity of the tubular motor (see end of this
Manual)
▪Correct cable installation (loop facing down) will protect the
tubular motor against water damage.
▪Do not drill holes in the motor housing.
▪Protect the motor against contact with liquids.
▪Avoid shocks, impacts and damage to the motor.
▪
Fig. 1.

P. I. E. INEL Sp. z o. o., ul. Mostowa 1, 80-778 Gdańsk, [email protected] www.inel.gda.pl
2.2 Installing the tubular motor
•Attach the bracket (A) to the side of the roller blind
box, connect the adaptor (D) with the motor thrust ring.
•Connect the driver (E) to the motor axis and secure it with a
cotter pin (F). Insert the motor assembly into the roller tube
(G).
•The roller tube and the driver can be fixed with screws
or rivets (H)
Fig. 2.
NOTE: The motor is fitted with an internal thermal breaker that
allows the roller blind to work continuously for approx. 4 minutes,
after which the temperature inside the motor will exceed the
permissible value and trip the thermal breaker. The roller blind
can be operated again after the motor cools down (up to 20
minutes.) The thermal protection guarantees long service life of
the tubular motor.
2.3 Electrical connections
A monostable three-position (shutter blind switch) Scan be
connected to input 4 and 5 of the tubular motor. Press and
release UP to raise the roller blind; press and release UP or
DOWN to stop the roller blind.
TURN OFF THE POWER SUPPLY BEFORE MAKING
ANY CONNECTIONS!
Incorrect installation may result in motor stopping
unexpectedly.
Use rigid links and stops in the bottom strip to ensure
correct operation of the motor. The roller blind curtain
length must correspond to the length of the guides.
3 Starting and configuring the tubular
motor in InelControl system
The tubular motor can be added to the system after power on.
For information about registering, configuring and
operating the tubular motor, see “Control unit user
manual and InelControl system
configuration”.
4 Overload detection function
Type P tubular motor monitors the motor for overload (reduced
speed) in the upward and downward direction. If the speed falls
below a certain value (determined based on the position of the
motor in the end position or outside of the end position), the
motor will stop to prevent further movement in this direction.
When the roller blind is stopped at the same point twice, the
motor sets its limit position at this point. The motor will show
higher sensitivity to overload at the distance within a quarter turn
of the roller tube upwards and a quarter turn of the roller tube
downwards from this point. The motor will gently stop at the
bottom rigid link and at the stops in the top section of the
window.
The tubular motor is factory set by the manufacturer. The
tubular motor will adapt to the roller blind after making two stops
in the upper and lower limit positions. The motor can also be set
automatically in the app. The tubular motor is ready to use.
The motor detects low speed due to overload and prevents
movement in the direction it was moving before stopping. To
unlock the tubular motor, move it for at least 1 second in the
opposite direction.
Before starting/programming the tubular motor,
check the roller blind curtain, guide and roller blind
box condition and make sure the window is fitted
with a window sill.
The roller blind box and guides must be free from dirt
and allow free movement of the roller blind curtain at
its entire lenght. Dirty or tight guides may cause
damage to the tubular motor and the roller blind that is
not covered by the warranty.
Fig. 3.
1 - yellow/green
2 - blue
3 - brown
4 - grey
5 - black
L1 - live
N - neutral (blue)
PE - protective earth
(yellow/green)

P. I. E. INEL Sp. z o. o., ul. Mostowa 1, 80-778 Gdańsk, [email protected] www.inel.gda.pl
5 Troubleshooting
Problem: Motor is not responding.
Cause: Thermal protection triggered.
Solution: Wait for 10 to 20 minutes.
Problem: Motor turns in the opposite direction to
selected on the remote control.
Solution: Switch the motor direction in the app.
Problem: Motor stops automatically.
Cause: Roller blind curtain stuck in the guides.
Solution: Check the roller blind curtain slats and guides.
SPECIFICATIONS
6 Specifications
YYGL35PR-
10/17
YYGL45PR-
20/15
Power supply
230 V 50Hz
230 V 50Hz
Torque
10 Nm
20 Nm
Power
131 W
161 W
Speed
17 rpm
15 rpm
Protection rating
IP 44
IP 44
Continuous operation
time
4 min.
4 min.
Motor length
555 mm
530 mm
Weight
1.8 kg
2.5 kg
7 Motor selection table
Roller blind height
1.5 m
2.0 m
2.5 m
3 m
Torque
Roller tube
diameter
Permissible roller blind weight
by height
N-10 Nm
Φ = 40 mm
20 kg
19 kg
18 kg
17 kg
N-20 Nm
Φ = 60 mm
42 kg
40 kg
38 kg
36 kg
8 Disposal
Do not dispose of with household waste.
Dispose of waste in accordance with the
relevant legislation. Households play a key role
in the recycling of waste electrical and electronic
equipment. Waste sorting, including waste
equipment and batteries, guarantees that the
equipment is not disposed of with household
waste but is handed over to a designated collection point for
the recycling of waste electrical and electronic equipment.