Inficon IO1000 Instruction Manual

Quick-start installation guide for I/O1000 I/O module
Safety instructions
This quick-start guide does not replace the
installation manual for the I/O1000 I/O module.
Safe use of the module is ensured only by reading
the installation manual.
Additional important information is provided in
the installation manual for the I/O1000 I/O module.
The manual can be found either on the USB
memory stick or on the INFICON website. The USB
memory stick is included with the shipment of the
I/O module.
Intended use
The I/O module is a device interface between the MSB
box of the mass spectrometer module LDS3000 and
an external controller, for example.
►Install, operate and service the unit only in
compliance with the installation manual.
►Comply with the limits of application.
User requirements
►Operate and install the unit only if it is in perfect
working order and as intended, in a safety-
conscious manner and fully aware of dangers, in
compliance with this manual.
►Fulfill and ensure compliance with the following
regulations:
– Intended use
– Generally applicable safety and accident
prevention regulations
– International, national and local standards and
guidelines
– Additional provisions and regulations that are
specific to the unit
►Use only original parts or parts approved by the
manufacturer.
►Keep the installation manual available at the
operating site.
►All work must be performed only by technical
specialists who have been trained on the unit.
►Allow personnel in training to work with the unit
only under the supervision of technical specialists.
►Make sure that the authorized personnel have read
and understood this manual and all other
applicable documents, especially the information
on safety, maintenance and repairs, before starting
work.
►Define responsibilities, authorizations and
supervision of personnel.
User requirements
►Read, observe and follow the information in the
installation manual and the working instructions
created by the owner, especially the safety
instructions and warnings.
►Perform all work based on the complete manual.
Document: jima10en1-03 (1503)

Mounting of I/O module
DIN-TS35 top hat rail
1Hook unit on top hat rail at bottom.
2Press unit onto top hat rail at top.
Connecting I/O module with leak detector
The I/O module communicates via data cable with the
leak detectorand is supplied with voltage by the data
cable.
Data cables from INFICON
1Connect I/O module (connection LD) via data cable
with leak detector.
2Connect I/O module via desired interfaces with
external controller:
• RS232 (RS-232 interface)
• RS485 (RS-485 interface)
•A
NALOG IN(analog input)
•A
NALOG OUT (analog outputs)
•P
LC IN(digital inputs)
•P
LC OUT (digital outputs)
Description of the layout
see Installation Manual for I/O module, jiqc10.
FUSE and DIP switch S1, S2 f
Fuses for digital outputs and DIP switches (under the
cover)
Fuses for digital outputs 1 ... 4 and 5 ... 8:
2 x 0.75 A (Schurter: 7010.9800.xx)
1 = ON, 0 = OFF
1 = ON, 0 = OFF, + = switching from OFF to ON during
operation,
X = random
Fig: 1 Mount I/O module on DIN-TS35 top hat rail
Fig: 2 Rear view of I/O module
1 PLC IN
2RS232
3STATUS
4 ANALOG OUT
5PLCOUT
6 S1, S2 and FUSE
7LD
8ANALOGIN
9 RS485
10 24V OUT
DIP switch S1 LDS
3000 HLD 6000 Contact
4321
Factory setting (default
value of the interface
protocol by the leak
detector or control unit)

0000
ASCII protocol 0010
LD protocol 0011
Binary protocol 0101
LDS1000 protocol 0110
Normal protocol 0001
Simple protocol 0100
DIP switch S2 Contact
4321
Activate boot mode for software update X + 0 0
Disable bus terminator 120 Ωfor RS-485 1 X 0 0
INFICON GmbH, Bonner Strasse 498, D-50968 Cologne, Germany
Visit our website for contact information and other sales offices worldwide. www.inficon.com
Document: jima10en1-03 (1503)