Accuphase DAC-30 User manual


 




使用方法
取り付け方法
取扱説明書
820-3268-00 (B1) Printed in Japan
L101.5X
ディジタル入力ボード DAC-30
お願い 製品に対するお問い合わせ、または異常が認めら
れるときは、お求めの当社製品取扱店または、当
社品質保証部へご連絡ください。
お客様カードは付属していません。
アキュフェーズ株式会社
〒２２５-８５０８ 横浜市青葉区新石川２-１４-１０
 TEL０ ４ ５（ 9 ０ １ ）２ 7 7 １（ 代）
＊イラストは E-460 です。



接続ケーブル
  
  
  
保証特性、適合規格
  
  
 
  
  
   
   
  
COAXIAL 端子 
OPTICAL 端子
USB 端子
注意 


 󰴤 󰴥
󰴦
 




❶
❷
 図 1 
 
❸
 図 2 


❹
 
 
 

 


 

ガイドレール
ガイドレール
724-0019-00
724-0020-00
TOSHIBA
74HCTO
NFV510
20MHz0.24
サブパネル
オプシ ョ ン ・ ボード
図1 図2
注意
＊プラグ先端の
保護キャップをはずす。
端子の保護プラグを抜く。
端子がシャッター付き
の場合
端子が保護プラグ付き
の場合
端子：押すとシャッターが
プラグ
光ファイバー
内側に開く。
OPTICAL端子
端子とプラグのガイドを
合わせてしっかり差し込む。
端子とプラグの形状を合わ
せてしっかり差し込む。
タイプBプラグ
USBケーブル
USB端子
＊USB ダストカバーを取る。
光ファイバーの接続
USB（タイプB）の接続
プラグ
プラグ

注意 E-３0８, C-２4５, CX-２60への増設について

 

ACCUPHASE LABORATORY, INC.
2-14-10, SHIN-ISHIKAWA, AOBAKU, YOKOHAMA 225-8508, JAPAN
820-3268-00 (B1) Printed in JapanL101.5X
INSTRUCTION MANUAL
Digital Input Board DAC-30
Note If installing on an E-308, C-245, or CX-260…
Owing to power limitations, these devices cannot accept more than a single DAC-30. You can,
however, install both a DAC-30 and an AD-20 (Analog Disk Input Board) for simultaneous use.
Thank you for your purchase of the DAC-30 digital input board. This option board accepts digital
music signals from the digital outputs on CD players, MD players, and similar devices, and plays
out the music. You can connect to the player using either coaxial cable or optical fiber.You can also
use USB cable to connect to and play music data on a personal computer. Install this board into
an option slot on the rear panel of your analog device, and use its digital input jacks to connect to
the external source. Usage procedures vary according to the device on which the board is used;
please be sure to read the documentation that came with that device before starting use.
Using the DAC-30
How to Install Illustration shows installation on the E-460.
COAXIAL Accepts digital coaxial cable.
OPTICAL Accepts JEITA-compliant optical fiber cable.
Notes When connecting a component, please do not connect up both coaxial cable and
(balanced or line (unbalanced)) analog cable at the same time. Simultaneous
connection of both cable types will produce a ground loop, resulting in electrical
noise.
 The DAC-30 will automatically lock in the input signal from the coaxial, optical,
orUSB connector, in that order, when power comes on or when the input
selector is set to OPTION.
 To select the input jack to use on the DAC-30 (coaxial, optical, or USB): disconnect
the input cables you do not wish to play from, or else switch off the power to the
input devices you do not wish to play from.
◆ For information about how to set up and use a computer connected by USB, refer
to the computer's user documentation.
❶Turn off the device power.
❷On the rear panel, remove the slot cover of the
slot you wish to use. (see Fog. 1 )
◆Retain the slot for future use.
❸
Insert the board along the top and bottom guide
rails in the slot (see Fog. 2 ).
Push the board in gently until it touches the
connector at the back of the slot, and then give
it a firmer push so that it seats fully into the
connector.
❹
Secure the board by screwing in the top and
bottom screws.
 Turn off the device power before installing or removing option boards. Installing
a board while power is on may damage the equipment.
 Keep fingers out of the opened slot. Do not place anything other than the board
into the slot.
 Avoid touching the board’s soldered areas, connector contacts, and
components. Touching these areas may damage the circuitry or the contact.
Hold the board by the edges or along its panel.
 Tightly screw in the two screws all the way (by hand). If screws are loose,
terminals may separate from ground, resulting in poor contact or equipment
damage.
Guide rail
Guide rail
724-0019-00
724-0020-00
TOSHIBA
74HCTO
NFV510
20MHz0.24
Fog. 1 Fog. 2
Sub
panel
Option
board
Caution
*Remove plug cap.
Pull off the blind plug.
If connector is
shuttered:
If connector has a
blind plug:
Cable plug
Optical fiber cable
Push to open
shutter.
OPTICAL jack
Align plug guide with
jack, and push in firmly.
Align the plug with the
port and push firmly in.
Type-B plug
USB cable
USB port
*Remove the USB dust cover
Connecting optical
fiber cable
USB (Type B) connection
Plug
Plug
*Retain the protection cap and dustcover for future use.
Adds one coaxial input, and one optical-fiber input, and one USB input to the device.
Use these to input digital sound signals from digital components. To select which of the
three inputs is used: Leave the input you do not wish to use empty, or else turn off the
component connected to it.
Connection cables
COAXIAL: Connects to digital coaxial cable.
OPTICAL: Connects to optical fiber cable.
USB: Connects to cable with USB type B connector end
Guaranteed specifications
Input format: IEC 60958/AES-3 for COAXIAL and OPTICAL, and
USB2.0 Full Speed (12M bps)
Sampling freq: 32-96 kHz (OPTICAL, USB),
32-192 kHz (COAXIAL)
Quantization bit rate: 24 bits
Digital input: COAXIAL 0.5 Vp-p, 75 ohms
OPTICAL -27 to -15 dBm
USB
USB Port USB (Type B) connection