Infinity FS-ITM User manual

Installation Guide
Floor Stands for
Intermezzo
™
2.6 or
Interlude
™
IL10 Speakers
FS-ITM/IL FLOOR STAND

Note: Place recessed holes
for Interlude Foot Pads
face up.
Assembly viewed
from the left
Note: When assembled, the slot
for wire access on the tower top
should face the left side.
5/16 x 18 FLAT
HEAD SCREWS (2)
Front
Left side
Right side
Back
Interlude Mounting
Plate
2FS-ITM/IL
5/16 x 18 FLAT
HEAD SCREWS (2)
BASE
TOWER
Cord access slot
in tower top
Cord access slot
in base bottom
FOOT PADS (4)
SPIKED FEET with
NUT assemblies (4)
5/16 x 18 FLAT HEAD
SCREWS (4) BASE
TOWER
INTERLUDE IL10
MOUNTING
PLATE
INTERMEZZO 2.6
MOUNTING
PLATE
Included – This Infinity speaker stand is designed to be used with the
Intermezzo 2.6 or Interlude IL10 speaker.Below are the pieces that are
included for this speaker stand.
Intermezzo 2.6 –When used with Intermezzo 2.6
speakers,the rounded edge of the Mounting Plate should face
the outer side of the stand assembly;the same side as the
decorative side panel on the front of each Intermezzo speaker.
STEP 2A
ScrewTower to Base with (2) 5/16 x 18 Round Head
Screws.Note that it is important which direction the slot in the
TowerTop faces depending on the application desired.See
Steps 2A and 2B for possible applications.
Outer
side Outer side
Assemblies viewed
from the rear
Assembly
for RIGHT
side use
Assembly
for LEFT
side use
Note: The slot for cord and
wire access is facing the rear
The Intermezzo Mounting Plate
is simply turned over for left or
right application
5/16 x 18
FLAT HEAD
SCREWS (2)
5/16 x 18
FLAT HEAD
SCREWS (2)
Interlude IL10 –When used with Interlude IL10
speakers,the assembly process is the same,regardless of LEFT
or RIGHT placement.
STEP 2B
STEP 1

Interlude or
Intermezzo
Mounting
Plate
SPIKE
BOLT
FOOT
SPIKE BOLT
FOOT/NUT
ASSEMBLY
NUT
BASE
FOOT PADS
3
FS-ITM/IL
The floor stand includes both spikes and felt pads.For
installations on a carpet,we recommend the use of the spikes as this will
provide maximum stability and acoustic isolation.For applications where
there is a floor surface that may be damaged by the spikes,felt pads are
also provided.The Spike Feet are comprised of a Spike Bolt and a Nut that
tightens to lock the Spike Bolt in place.
STEP 3
120 Volt
Speaker wires
Speaker end
of power
cord
Speaker
wires
Insert speaker end of power cord in cord access hole in base
and feed it up and out through the top.Run the speaker wires in the same
manner.
STEP 4
Intermezzo 2.6
Speaker
Mounting
Screws (4)
supplied
with speaker
Screw holes
in base of
Intermezzo
Intermezzo 2.6 – Place the Intermezzo speaker on its
mounting plate and secure with (4) screws (provided with the
speaker).
STEP 5A
Interlude IL10
Speaker
Foot Pad
recesses
Interlude IL10 – Place the Interlude speaker on its
mounting plate and align its (4) Foot Pads with the Foot Pad
recesses.
STEP 5B

© 2000 Infinity Systems,Inc.,250 Crossways Park Drive,Woodbury,NY 11797 USA [phone] (USA Only) www.infinitysystems.com
Infinity is a registered trademark of Infinity Systems,Inc.Printed 4/00 Part No.FS-ITM/ILOM