Infinity Total Solutions TSS-CENTER4000 User manual

TSS-CENTER4000
Owner’s Guide
TOTAL SPEAKER SOLUTIONS
TSS-4000
INFP1594Center-4000om 10/18/04 2:34 PM Page 1

INTRODUCTION
InfinityTotal Solutions™
Infinity Total Solutions TSS-CENTER4000 center channel
loudspeaker is designed to perfectly complement theTSS-SAT4000
speakers. It uses identical drivers to provide exceptional
dialogue reproduction and a seamless transition between the
front channels.The horizontal design allows for maximum
placement flexibility.
AboutThis Guide
Please read this guide completely before connecting and
operating theTSS-CENTER4000 center channel speaker.
Maximum performance is dependent upon following these
instructions, as well as those in the owner’s manuals of
associated components in your home theater system. Save
these instructions for future reference.
Unpacking the Speaker
Finish unpacking the speaker and check the contents. If you
suspect damage from transit, report it immediately to your
dealer. Keep the shipping carton and packing materials for
future use.
Contents
Please verify that the package contains the following items:
PLANNING YOUR SYSTEM
Before deciding where to best place your speakers, survey your
room and study Figures 1 and 2.
Figure 1. In this overhead view of a typical installation, satellite
speakers are used to reproduce sound for the front and surround
channels.The center channel reproduces sound and dialogue.
The powered subwoofer provides bass for effects and music.
Placement
Figure 2.This example shows the TSS-CENTER4000 being placed
on top of a television.The speaker can also be placed below the
television and tilted up (see Figure 3).
Couch
Left
Front
Channel
Left
Surround
Channel
Right
Surround
Channel
Right
Front
Channel
Center
Channel
(above or below TV) Subwoofer
(1) TSS-CENTER4000 center channel speaker
(1) Speaker base
(1) Wall bracket with wall bracket cover
2TSS-CENTER4000
Part A
Part B
(2) Wall-mount end caps
(attached to satellite)
(1) Allen
wrench
INFP1594Center-4000om 10/18/04 2:34 PM Page 2

3
TSS-CENTER4000
Tilting the Speaker
If needed, the enclosed stand allows you to tilt the speaker
across a wide range (i.e., up a maximum of 18˚ or down a
maximum of 7˚), as shown in Figure 3.
Important!
Do not exceed the tilt range. Doing so may cause the speaker to
fall out of its stand.
Figure 3.
Wall-Mounting theTSS-CENTER4000 Using the
Included Wall Bracket
The customer is responsible for proper selection and use of
mounting hardware, and for correctly and safely wall-mounting
the speakers.
Step One
Remove the wall bracket cover by removing the four wall bracket
screws on the ends as shown.
StepTwo
Run the speaker wire behind the wall bracket and out the hole
in the center. After deciding where to place the center speaker,
attach the wall bracket (in a horizontal position) to the wall
using the appropriate screws and anchors.
StepThree
Run the speaker wires out through the hole in the center of
the wall bracket cover. Resecure in place with the four wall
bracket screws, as shown.
Mounting Screws and Anchors
Not Included
Wall Bracket
Center Hole
INFP1594Center-4000om 10/18/04 2:34 PM Page 3

4TSS-CENTER4000
Step Five
Connect the wires (page 5). Replace the end caps while
capturing the wall bracket between parts A and B of the
end cap,securing it in place.
Wall-Mount
End Cap A
Wall-Mount
End Cap B
Step Four
Using the included Allen wrench, remove the top and bottom
end caps of the speaker by unscrewing the single center screw
on bottom.
End Cap
1/4-20 x 3/4"
Screw
End Cap
Step Six
The wall-bracket design allows for rotation of the speakers
at angles up to 30 degrees of center. Position the speakers
so they face toward the primary listening position, before
fully tightening.
INFP1594Center-4000om 10/18/04 2:34 PM Page 4

5
TSS-CENTER4000
WIRING THE SPEAKER
After placing the speaker, you are ready to connect it to your
system. First, turn off all audio system power. Use high-quality
speaker wire to make the connections. Consult the owner’s
manuals included with your amplifier or receiver for connection
and operation procedures.
Surround Modes
When using theTSS-CENTER4000 in a Dolby* Digital or DTS®
home theater system, make sure the receiver’s/processor’s
center channel speaker modes are set to“Small.”
Wiring and Polarity
The TSS-CENTER4000 speaker has gold-plated terminals that
can accept bare wire.To ensure proper polarity, connect each
+ terminal on the back of the amplifier or receiver to the
respective + (red) terminal on each speaker, as shown in
Figure 4. Connect the – (black) terminals in a similar way.
See the owner’s manuals that were included with your
amplifier or receiver to confirm connection procedures.
Important!
Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will degrade the imaging and bass
response of the home theater system.
After correctly placing and wiring theTSS-CENTER4000 and
the rest of your speaker system, adjust the levels for all of the
channels as recommended by the manufacturer of your
receiver/processor.
Figure 4.This example shows how to connect bare wires to the
terminals. Banana plugs may also be inserted directly into the
rear of the connector.
1Loosen the terminals.
2Insert bare ends; tighten terminals.
– +
1
2
CARE OF YOUR SPEAKER SYSTEM
When needed, use a soft cloth to remove any fingerprints or
to wipe off dust. Do not use any cleaning products or polish.
Clean the grille by gentle vacuuming.
INFP1594Center-4000om 10/18/04 2:34 PM Page 5

6TSS-CENTER4000
SPECIFICATIONS
TSS-CENTER4000
Frequency Response 120 – 20kHz (±3dB)
Nominal Impedance 8 ohms
Sensitivity 89dB
(2.83V @ 1m)
Recommended Amplifier 10 – 150 watts
Power Range
Crossover Frequencies 1,000Hz, 3,800Hz; 24dB/octave
Low Frequency Drivers (4) 3-1/2" (89mm) MMD® ,
magnetically shielded
Mid Frequency Drivers (2) 3-1/2" (89mm) MMD,
magnetically shielded
High Frequency Driver 3/4" (19mm) MMD,
elliptical waveguide,
magnetically shielded
Dimensions (H x W x D) 4-1/8" x 23" x 4-3/8"
(105mm x 584mm x 111mm)
Weight 12.7 lb (5.8kg)
Infinity continually strives to update and improve existing products, as well as create new ones.
The specifications and construction details in this and related Infinity publications are therefore
subject to change without notice.
Declaration of Conformity
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the product
described in this owner’s manual is in compliance
with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Robin Marshall
Harman Consumer International
Chateau-du-Loir, France 10/04
INFP1594Center-4000om 10/18/04 2:34 PM Page 6

NOTES
INFP1594Center-4000om 10/18/04 2:34 PM Page 7

© 2004 Harman International Industries,Incorporated
Infinity Systems,250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4INF (USA only) www.infinitysystems.com
*Trademarks of Dolby Laboratories. DTS is a registered trademark of DigitalTheater Systems, Inc. Infinity and MMD are registered trademarks,
and Total Solutions is a trademark, of Harman International Industries,Incorporated.
Part No.400-OMCNTR 10/04
INFP1594Center-4000om 10/18/04 2:34 PM Page 8