Init NT-Retro-C User manual

Adjustment
knob
Grill ring
Grill
Base
Fan blade
Oscillation
knob
Power switch/
speed selection
Quick Setup Guide
12" Table Fan
NT-Retro-C/NT-Retro-S
Features
Servicing instructions
To replace the fuse
1Unplug the fan.
2Slide open the fuse access cover
on top of the AC power plug.
3Remove the fuse.
4Replace the fuse only with a 5A, 125 Volt fuse. Do not force the fuse
in place.
5Slide the fuse access cover on top of the AC power plug closed.
Caution: Do not replace the AC power plug. Discard the product if the
plug is damaged.
Cleaning your fan
• Be sure to unplug your fan before cleaning.
• Plastic parts should be cleaned with mild soap and a damp cloth or
sponge. Thoroughly remove soap lm with clear water.
• Be sure not to splash water or other liquid into the motor.
Package contents
• 12" table fan
• Quick Setup Guide
Using your fan
O/speed selection
The power switch is incorporated in the speed control switch on
the top of the fan.
0 - The fan is switched o.
1 - The fan operates at a low speed.
2 - The fan operates at a medium speed.
3 - The fan operates at a high speed.
Oscillation
To allow the fan to oscillate, push down the knob beside the fan
speed control. Pull up on the knob if you don’t want it to oscillate.
Adjustment
To adjust the angle at which the fan is blowing
1Loosen the adjustment knob under the fan motor.
2Adjust the fan to the angle you want, then retighten the knob to
secure the fan at that angle.

V2 ENGLISH 12-1210
Important safety instructions
1 READ AND SAVE THESE INSTRUCTIONS
2 To reduce the risk of re or electrical shock, do not use this fan for
any solid state speed control device.
3 If the power cord is damaged, it is strongly recommended to be
repaired by a qualied person.
4 This appliance has a grounded three-prong plug and is suitable for
grounded receptacle use only. If an adapter is used for connecting
three-blade grounding-type plugs to two-slot receptacles, the
adapter must be properly grounded.
DO NOT attempt to defeat the purpose of this safety feature.
5 Do not leave the fan running unattended.
6 Never insert ngers, pencils, or any other objects through the fan
housing when the table fan is running. Unplug the fan when
moving it from one location to another.
7 Disconnect the fan before cleaning.
8 To avoid overturning, be sure that the fan is placed on a stable
surface during operating
9 To reduce the risk of electric shock, DO NOT use the fan by a
window.
10 The rules about cords and plugs are as follows:
a. This product uses an overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse burns
out, unplug the product from the outlet. Replace the fuse as per
the user servicing instructions (follow product marking for proper
fuse rating) and check the products. If the replacement fuse
blows, a short circuit may be present and the product should be
discarded or returned to an authorized service facility for
examination and/or repair.
b. Do not operate any fan with a damaged cord or plug. Discard or
return the fan to an authorized service facility for examination
and/or repair.
c. Do not run the cord under carpeting. Do not cover the cord with
throw rugs, runners, or similar coverings. Do not route the cord
under furniture or appliances. Arrange the cord away from trac
areas and where it will not be tripped over.
One-year limited warranty
Visit www.initproducts.com for details.
Contact Init:
For customer service, call 800-573-2860
www.initproducts.com
INIT is a registered trademark of BBY Solutions, Inc. Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2012 BBY Solutions, Inc. All Rights Reserved.