Innotech BARRIER-ATTIKA User manual

BARRIER-ATTIKA
Instruction manual
© INNOTECH Arbeitsschutz GmbH. Irrtümer, Druckfehler, technische Änderungen vorbehalten! © INNOTECH Arbeitsschutz GmbH. Errors and misprints accepted. We reserve the right to make technical changes.
DE – ACHTUNG: Die Verwendung des INNOTECH-Produkts ist erst zulässig, nachdem die
Gebrauchsanleitung in der jeweiligen Landessprache vollständig gelesen und verstanden wurde.
DE
EN – ATTENTION: Use of the INNOTECH product is only permitted after the instruction
manual has been read and fully understood in the respective language.
EN
IT – ATTENZIONE: L'utilizzo del prodotto INNOTECH è permesso solo previa lettura e
comprensione dell'intero manuale di istruzioni nella lingua del relativo paese di utilizzo.
IT
FR – ATTENTION : L'utilisation du produit INNOTECH n'est autorisée qu'après avoir
entièrement lu et compris la notice d'utilisation dans la langue du pays concerné.
FR
NL – ATTENTIE: Dit INNOTECH-product mag pas gebruikt worden nadat u de gebrui-
kershandleiding in de taal van het betreffende land gelezen en begrepen hebt.
NL
ES – ATENCIÓN: Se autorizará el uso de los productos INNOTECH una vez que se hayan
leído y entendido las instrucciones de uso en el idioma del país.
ES
PT – ATENÇÃO: O uso do produto INNOTECH apenas é permitido depois de ter lido e
compreendido na totalidade as instruções de uso na respetiva língua nacional.
PT
DK – GIV AGT: Du må først bruge et produkt fra Innotech, efter du har læst og forstået
brugsvejledningen i fuldt omfang i dit lands sprog.
DK
SV – O B S : Denna INNOTECH-produkt får inte användas förrän bruksanvisningen på
respektive lands språk har lästs igenom och förståtts.
SV
CZ – POZOR: Práce s výrobkem INNOTECH je povolena teprve po kompletním přečtení a
porozumění návodu k použití v jazyku daného státu.
CZ
PL – UWAGA: Produkty firmy INNOTECH mogą być używane dopiero po dokładnym
zapoznaniu się z całą instrukcją obsługi w ojczystym języku.
PL
SL – POZOR: Uporaba izdelka INNOTECH je dovoljena šele po tem, ko ste navodila preb-
rali v celoti v ustreznem jeziku svoje dežele in jih tudi razumeli.
SL
SK – POZOR: Produkt INNOTECH môžete používať až po prečítaní a porozumení celého
návodu na použitie pre príslušnú krajinu.
SK
HU – FIGYELEM: Az INNOTECH termékek használata csak azt követően engedélyezett,
hogy saját nyelvén elolvasta és megértette a teljes használati utasítást.
HU
TR – DİKKAT: INNOTECH ürününün kullanımına ancak ilgili ülkenin dilinde sunulmuş
olan kullanım kılavuzunun tamamen okunmasından ve anlaşılmasından sonra izin verilir.
TR
ZH – 注意：只有在仔细阅读并完全理解了当地语言的使用说明后，才能使用 INNOTECH 公司的产品。
ZH

2BARRIER-ATTIKA/190611/www.innotech.at
EN
1TABLE OF CONTENTS
[2] DESCRIPTION OF SYMBOLS 3
[3] SAFETY INSTRUCTIONS 4
[4] COMPONENTS/MATERIAL 6
[5] PRODUCT SUITABILITY/APPROVAL 9
[6] INSPECTION 10
[7] WARRANTY 11
[8] SIGNS & MARKINGS 11
[9] INSTALLATION TOOLS 12
[10] INSTALLATION 13
[11] SYSTEM-PARAPET AT TOP 13
[12] SYSTEM-PARAPET AT SIDE 23
[13] SYSTEM-PARAPET AT SIDE, HINGED 32
[14] DISPOSAL 41
[15] ACCEPTANCE LOG 42
[16] INFORMATION ON THE SAFETY SYSTEM 44
[17] TEST LOG 45
[18] DEVELOPMENT & SALES 47

3
EN
BARRIER-ATTIKA/190611/www.innotech.at
2DESCRIPTION OF SYMBOLS
Supplementary information/instructions
Warning/danger information
An IMMEDIATE threat of danger that can cause serious physical injuries
or death.
ücorrect incorrect
A POTENTIALLY dangerous situation that causes serious physical injuries
or death.
A POTENTIALLY dangerous situation that could lead to minor physical
injuries and damage to property.
DANGER
WARNING
CAUTION
Comply with manufacturer's instructions/applicable instruction manuals.
Wear protective gloves!
Wear safety glasses!
Work surface: Surface on which the persons stand, walk, or work.
All vertical dimension specications are provided in relation to this
surface.
Danger of falling/edge

4BARRIER-ATTIKA/190611/www.innotech.at
EN
3SAFETY INSTRUCTIONS
3.1 GENERAL
- The safety system may be installed only by specialised/competent experts familiar
with the system safety system, and in compliance with the current state of the art.
- The safety system may be installed or used only by persons who are:
• trained in "personal protective equipment" (PPE),
• in good physical and mental health (medical conditions such as
cardiovascular problems, intake of medicines, consumption of alcohol, etc.
negatively aect the safety of the user.)
• familiar with the locally applicable safety regulations.
-A plan must be available that species the rescue procedures for all possible
emergencies.
- Before starting work, ensure that no objects from the work site can fall to the
ground. The area below the work site (pavement, etc.) must be kept clear.
- Plan, install, and use the safety system in such a way that no-one can fall over the
edge if it is used correctly. See planning documents at www.innotech.at.
- Do not make any changes to the safety system.
- The maximum roof pitch of the installation substructure must not exceed 10°.
- If used on inclined roof surfaces, roof avalanches (ice, snow) must be avoided by
means of suitable snow interception devices.
- During the installation/use of the safety system, the relevant accident prevention
regulations must be complied with, as must the rules and standards for the use of
personal protective equipment designed to prevent falls.
- When installation is complete, this instruction manual must be stored by the building
owner and made available to the user.
-If you supply the safety system to external contractors, these latter must conrm in
writing that they have understood this instruction manual.
- If the equipment is sold to another country, the instructions of use must be provided
in the respective national language.
- Comply with the local lightning protection regulations.
Comply with the following safety instructions and the latest state of the art.

5
EN
BARRIER-ATTIKA/190611/www.innotech.at
3SAFETY INSTRUCTIONS
3.2 FOR FITTERS: FOR SAFE INSTALLATION
3.3 FOR USERS: FOR SAFE USE
- All stainless steel bolts must be greased with a suitable lubricant before installation
(provided: Weicon AntiSeize ASW 10000 or equivalent quality)
- Ensure that stainless steel does not come into contact with swarf or steel tools, as
this can lead to corrosion.
- For installation, always select a safety system that is suitable for the prevailing
conditions.
-The tter must ensure that the substructure is suited for xing the anchorage
device.
- The substructure must be free of snow and ice throughout the installation.
- The safety system must consist of at least 2 posts.
-Use dowel logs and photos of each installation situation to document the professional
attachment of the safety system to the building structure.
- The roof covering must be correctly sealed as per applicable guidelines.
- Correct use of the individual elements including "personal protective equipment"
must be ensured, because otherwise the safe functioning of the safety system is
NOT guaranteed.
- Do not use safety systems if wind speeds exceed normal parameters (max. wind
zone 4).
If uncertainties arise during the installation, it is imperative that you contact
the manufacturer.

6BARRIER-ATTIKA/190611/www.innotech.at
EN
4COMPONENTS/MATERIAL
Instruction manual
Z11: Rating plate
BARRIER
DIN 19 class AEN 13374:20
EN ISO 14122-3:2016
DIN 14094-2:2017
system no.: Install :ed by
dat nstallation:e of i
XXXX XXXX XXXX
11-08-1 -010-Aufkleber-E -1 ND
length: m
S.Nr.: JJJJ-..-...
www.innotech.at
4.1 COMPONENTS
4.1 SYSTEM COMPONENTS
A10: Aluminium, stainless steel 304
Adapter on the side of the parapet
A11: Aluminium, stainless steel 304
Adapter on the side of the parapet, foldable
A31: Aluminium, stainless steel 304
Spacer bracket for parapet
A22: Aluminium, stainless steel 304
Parapet adapter for attachment on the top of the parapet
D82: Aluminium, stainless steel 304
Adapter for AIO-STA post

7
EN
BARRIER-ATTIKA/190611/www.innotech.at
4COMPONENTS/MATERIAL
R11: Aluminium
Aluminium pipe, straight
R21: Aluminium, stainless steel 304
Linear tie
R31: Aluminium, plastic, stainless steel 304
Corner tie
R41: Aluminium, stainless steel 304
Wall tie
F20: Aluminium
Toe board
F23: Aluminium, stainless steel 304
Toe board connection set
F21: Aluminium, stainless steel 304
Toe board bracket for fastening the toe board
to the BARRIER-S21 post

8BARRIER-ATTIKA/190611/www.innotech.at
EN
4COMPONENTS/MATERIAL
S23-560: Aluminium, aluminium/zinc, stainless steel 304
Stiening strut
T30: Aluminium, stainless steel 304
Door set
R51: Aluminium, stainless steel 304
End seal
R91: Plastic
Cap for BARRIER-R11 aluminium pipe
S21-1050: Aluminium, aluminium/zinc,
stainless steel 304
Post, PARAPET system
Standard length: 1050 mm
Special lengths upon request
Z22: Aluminium/zinc
End cap for a standard upright
R70: Aluminium/zinc, stainless steel 304
Pipe retainer for BARRIER-R11 aluminium pipe

9
EN
BARRIER-ATTIKA/190611/www.innotech.at
INNOTECH "BARRIER" was developed as a side protection system (railing) for
collective, permanent fall prevention on roof surfaces which are not publicly accessible.
Comply with the manufacturer's instructions for the personal
protective equipment being used.
5PRODUCTSUITABILITY/APPROVAL
DANGER TO LIFE through incorrect use.
- Use INNOTECH "BARRIER" ONLY for personal safety.
- Do NOT climb onto the INNOTECH "BARRIER".
-NEVER lean ladders against the INNOTECH "BARRIER".
-DO NOT use INNOTECH "BARRIER" as a personal leaning support for
hoisting or lowering scaolds, construction and cleaning materials, etc.
!
DANGER
INNOTECH "BARRIER" was tested and certied to the requirements of the standards
EN ISO 14122-3:2016, DIN 14094-2:2017, and DIN EN 13374:2019 class A.
The notified authority participating in the type test is:
DEKRA Testing and Certification GmbH, Dinnendahlstrasse 9, D-44809 Bochum, Germany
≥
1100
≤
470
≤
470
≤
470
≥
150
15°
30°
≥
1100
5.1 ASSEMBLY VARIANTS
Pipe bracket always in the direction of the work surface!

10 BARRIER-ATTIKA/190611/www.innotech.at
EN
6.1 INSPECT BEFORE EVERY USE
6INSPECTION
Refer to the test log for inspection intervals.
If there are any doubts concerning the safe use of the safety
system, it must NOT be used any more, and must be checked by an
expert (written documentation). If necessary, the product must be
replaced.
6.2 INSPECT REGULARLY
INNOTECH “BARRIER” is maintenance-free. Every 2 years, the system must be
inspected by an expert, familiar with the safety system. The user's safety depends on
the eectiveness and durability of the equipment.
Shorter inspection intervals may be required, depending on the intensity of use and the
environment (e.g. in corrosive atmospheres, etc.).
Document the inspection by the specialist/competent expert in the test log
of the instruction manual, and keep this with the instruction manual.
DANGER TO LIFE through damage to the INNOTECH "BARRIER".
- INNOTECH "BARRIER" must be in perfect working condition.
- Do NOT continue to use INNOTECH "BARRIER" if
• There is obvious damage or wear to its components,
• Other defects were observed (loose threaded joints, deformation,
corrosion, wear, etc.),
• Strain has occurred due to a fall against or into the side protection
system,
• It is not possible to read the product labelling.
!
DANGER
Prior to each use, INNOTECH "BARRIER" must be inspected visually for any obvious
defects.
Check the entire safety system's suitability for use on the basis of the acceptance log
and test log.

11
EN
BARRIER-ATTIKA/190611/www.innotech.at
A) Name or logo of the manufacturer/retailer: INNOTECH
B) Type designation: BARRIER
C) Signs stating that instructions
for use must be followed:
D) Year of manufacture and manufacturer's
serial number: JJJJ-..-...
E) Numbers of the applicable standards: DIN EN 13374:2019 class A,
DIN EN ISO 14122-3:2016,
DIN 14094-2:2017
F) System no.: Allocation of numbers if there are
several side protection systems
G) Length: Length of the side protection
system in metres
H) Date of installation: Year installed: 
I) Name & address of the installation company: Installed by:
7WARRANTY
The warranty period for manufacturing defects on all components (under normal
conditions of use) is 2 years from the date of purchase. The time limit is shortened if it
is used in corrosive atmospheres.
If there is strain (a fall, weight of snow, etc.), the warranty claim is void for those
components that are designed to absorb energy or to deform.
For system installation and for components planned and installed
under the responsibility of specialised installation companies,
INNOTECH assumes neither responsibility nor warranty in the case
of incorrect installation.
BARRIER
DIN 19 class AEN 13374:20
EN ISO 14122-3:2016
DIN 14094-2:2017
system no.: Install :ed by
dat nstallation:e of i
XXXX XXXX XXXX
11-08-1 -010-Aufkleber-E -1 ND
length: m
S.Nr.: JJJJ-..-...
www.innotech.at
8SIGNS & MARKINGS
A
B
C
D
E
F
G
H
I

12 BARRIER-ATTIKA/190611/www.innotech.at
EN
9INSTALLATION TOOLS
[mm]
AF = 4
Installation tools, various replacement parts and accessories are available
from INNOTECH (www.innotech.at) (see INNOTECH price list).
AF = 2.5

13
EN
BARRIER-ATTIKA/190611/www.innotech.at
10 INSTALLATION
11 SYSTEM-PARAPET AT TOP
DANGER TO LIFE if NOT correctly installed.
- Install INNOTECH "BARRIER" correctly as per the instruction manual.
-Comply with the specied tightening torques.
!
DANGER
CAUTION INJURIES from sharp edges on components.
- Wear protective gloves for the installation work.
EYE INJURIES from dust/splinters/liquid.
- Wear eye protection/safety glasses for the installation work.
CAUTION
The separations, angles, etc. may vary with the circumstances
of the safety system.
[mm]
150 80
5
50 O
25
120
O
15
45
142 - 185
1053
1195 - 1238
≤
470
101
43
11.1 DIMENSIONS

14 BARRIER-ATTIKA/190611/www.innotech.at
EN
11 SYSTEM-PARAPET AT TOP
R11
F20
T30
F21
F23
R21
R51
R91
R41
A22
S21 Z11
Corners closed
R31
11.2 OVERVIEW
R11
F20
T30
F21
F23
R21
R51
R91
R41
A22
S21 Z11
Corners open

15
EN
BARRIER-ATTIKA/190611/www.innotech.at
11 SYSTEM-PARAPET AT TOP
[mm]
11.3 IMPORTANT DISTANCES
≤ 2200
≤ 400
≤
400
≤ 400 ≤ 2200 ≤ 2200
≤
2200
800
≥
100
≥
100
≥
75
≤
120
≤ 350
≤
350
400 ≤
400
≤
≤ 500 ≤ 500
75 ≥
≤
120
≥
1100
≤
470
≤
470
≤ 350
≥ 75
≤ 120
All separations, angles, etc. may vary with the circumstances of
the respective safety system.
The dimensions vertical to the oor always relate to the work surface.
T30
Corners open

16 BARRIER-ATTIKA/190611/www.innotech.at
EN
11 SYSTEM-PARAPET AT TOP
[mm]
≤ 2200
≤ 400
≤
900
≤ 400 ≤ 2200 ≤ 2200
≤
2200
800
≥
100
≥
100
≤
900
400 ≤
≤ 500 ≤ 500
75 ≥
≤
120
≥
1100
≤
470
≤
470
≤
350
≥ 75
≤ 120
All separations, angles, etc. may vary with the circumstances of the
respective safety system.
The dimensions vertical to the oor always relate to the work surface.
T30
Corners closed

17
EN
BARRIER-ATTIKA/190611/www.innotech.at
11 SYSTEM-PARAPET AT TOP
11.4 TOE BOARD
10
≤
≥
150
≥
150
≤
470
The dimensions vertical to the oor always relate to the work surface.
If the parapet is ≥ 150 mm or the separation between the top edge of the parapet and
the intermediate beam of the side protection system is ≤ 470 mm, then no toe board is
required.
[mm]
If the parapet is ≤ 150 mm, then a toe board is required.

18 BARRIER-ATTIKA/190611/www.innotech.at
EN
11 SYSTEM-PARAPET AT TOP
DANGER TO LIFE as a result of installation on unsuitable installation
substructure.
- Install INNOTECH "BARRIER" on a statically load-bearing construction
concrete (solid concrete) with a concrete quality of at least C20/25.
-DO NOT install on screed, levelling concrete, blinding concrete,
etc....
-Ensure that dowels are used correctly, as specied in the dowel
manufacturer's guidelines (correct cleaning of bores, compliance with
curing times and processing temperature, edge distances of the dowels,
inspection of the substructure, etc.)
-In case of doubt, have the installation substructure checked by a
structural engineer or by the manufacturer.
!
DANGER
11.5 INSTALLATION SUBSTRATE:
ADHESIVE ANCHORS
Adhesive anchor with M12 threaded rods, washer,
M12 lock nut, or nut with spring-lock washer
Penetration depth in concrete at least 100 mm
Compound mortar: FISCHER FIS SB 390 S HILTI HY 200
Use products from other manufacturers only if their
technical specifications are equivalent (compare product
data sheets).
11.6 FASTENING OPTIONS
The basic requirement for professional/correct installation is statically load-bearing
construction concrete (massive concrete) with a concrete quality of a minimum
of C20/25, and the use of the original fasteners listed in this instruction manual.
INNOTECH "BEF-104"
4 x concrete anchors

19
EN
BARRIER-ATTIKA/190611/www.innotech.at
11 SYSTEM-PARAPET AT TOP
1.
2 anchorage points are provided for installation.
(Parapet adapter for attachment on the top of the parapet A21: 2 x Ø 15 mm)
H
120
O
15
11.7 INSTALLATION
AF = 4
15 Nm
AF = 4

20 BARRIER-ATTIKA/190611/www.innotech.at
EN
11 SYSTEM-PARAPET AT TOP
2.
3.
430 -
0
Set the desired height. (Adjustment range = 43 mm)
430 -
0

Comply with the adjustment range.
ü