Inovativ Jackal User manual

PAGE 1
ASSEMBLY
Step 1) Begin by removing the main frame
from the case, standing it on its jockey
wheels and foot rests.
Step 2) Attach both main wheels, Release
the outer locking lever on the main axle.
Insert wheel pin into the axle. The pull pin
will click into place and re-secure the
locking lever.
To release the wheel, release outer locking
lever and pull the ring of the pull pin to
release the wheel.
Step 3) Attach seat. Place seat post into
seat bridge, insert safety pin into desired
height position [fig. 4]. Use locking knob [fig.3]to
secure seat.
Note: Tyres are deflated for shipping, please
inflate to desired pressure. Maximum
pressure limits are printed on the tyres.
[Fig.&1]&
Safety'Pin'
[Fig.&2]&
Safety'Pin'
[Fig.4]&
[Fig.&3]&

PAGE!2!
ADJUSTMENTS
Seat Position: Adjust fore/aft seat position by
releasing the seat bridge locking knobs[Fig.5],
remembering to re-tighten them once the
required position is found.
Adjust vertical seat position using the seat
post locking knob [Fig.3], making sure you
replace the safety pin [Fig.4]in required position.
Axle Width: To adjust the axle width, release
the inner axle locking lever and extend the
axle on both sides to desired length and lock
the inner lever.
Handle Position: To adjust the handles,
release the rosettes at the base of the vertical
handle poles. Adjust to the angle you require
and secure the rosettes.
Foot Rest Position: To Adjust the foot rest
position, release the locking knob, adjust the
foot rest to the appropriate position and
tighten the locking knob.
[Fig.&5]&
[Fig.&7]
[Fig.&6] Inner lever
[Fig.&8]

PAGE!3!
Jockey Wheel: Adjust the jockey
wheel friction by tightening and
loosening the jockey wheel friction
knob.
Jockey Wheel Removal: Fully remove the
jockey wheel caster lock nut [Fig. 10], hold jockey
wheel assembly and lift the Jackal chassis
away [Fig.11].
[Note: We recommend you attach the caster locking nut to the top of the
jockey wheel shaft for safe keeping]
[Fig.&9]
Jockey wheel
friction knob
[Fig.&10]
[Fig.&11]

PAGE!4!
ACCESSORIES
Camera Mount Accessory: To attach the
camera amount accessory, slide the tubes
through the main frame Tee. Attach both
rubber O-rings[Fig.14] in the two rear grooves
of the mount [Fig.13]. Adjust and lock into
place using the adjustment levers at the
base of the Main Frame Tee [Fig.12].
Support Brace: This is used to increase
stability with hard mounted heavy loads.
Attach the fixed end[Fig.16] of the brace to the
main axle of the Jackal[Fig.15] and the
adjustable end to the scaffold bar[Fig.14]. The
adjustable clamp can be switched sides
according to your hard mount position.
[Fig.&12]
Main FrameTee
[Fig.&13]
Rear Grooves
O-Ring!
[Fig.&14]
Adjustable End
Fixed
[Fig.14]
Main Axle Mounting Areas
[Fig.15]
Fixed End
Adjustable End
[Fig.16]
Adjustment Levers

PAGE!5!
CASE CONTENTS
JACKAL SPECIFICATIONS
Min
Length:
110 cm / 43 ¼”
186 cm / 79 ½”
Width:
70 cm / 27 ½”
Axle Extended:
99 cm / 39”
Height:
-
Handle:
112.5 cm / 44 ¼”
Post fitted:
125.5 cm / 49 ½”
Seat Height:
54 cm / 21 ¼”
70 cm / 27 ½”
Max load:
Operator & equipment:
150 kg / 330.69 lbs
Weight:
Standard Jackal:
27.6 kg / 60.8 lbs
Jackal with all accessories:
36.3 kg / 80 lbs
CASE SPECIFICATIONS
Length:
96 cm
37 ¾”
Width:
60 cm
23 ½”
Height:
45 cm
17 ¾”
Weight:
14 kg
30.8 lbs
[Fig.&14]
Main Chassis
Seat Seat Post
Safety Pin
Jockey Wheel
Seat Bridge Wheels
Camera Accessory Mount

PAGE!6!
WEIGHTS
Standard Jackal:
27.6 kg
60.8 lbs
Camera mount:
4 kg
8.8 lbs
Post:
1.4 kg
3.1 lbs
Support Brace:
1 kg
2.2 lbs
Accessory Mount:
2.3 kg
5 lbs
Case:
14 kg
31 lbs
Standard Jackal:
27.6 kg
60.8 lbs
Standard Jackal in case:
41.6 kg
91.7 lbs
Jackal with all accessories:
36.3 kg
80 lbs
Jackal with all accessories
in case:
50.3 kg
110.9 lbs
5600 Ayala Avenue, Irwindale, CA 91706
www.inovativ.com • [email protected] • 626.969.5300