Intelix INT-HD52 User manual

11675 Ridgeline Drive
Colorado Springs, CO
80918
Rev 170724 Phone: 719-260-0061
Toll-Free: 800-530-8998
Fax: 719-260-0075
INT-HD52 Owners Manual

INT-HD52 Owners Manual
2

INT-HD52 Owners Manual
3
Important Safety Instrucons
»Please completely read and verify you understand all instrucons in this manual before operang this equipment.
»Keep these instrucons in a safe, accessible place for future reference.
»Heed all warnings.
»Follow all instrucons.
»Do not use this apparatus near water.
»Clean only with a dry cloth.
»Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)
that produce heat.
»Use only accessories specied or recommended by Intelix.
»Explanaon of graphical symbols:
◊ Lightning bolt/ash symbol: the lightning bolt/ash and arrowhead within an equilateral triangle
symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the
product enclosure which may be of sucient magnitude to constute a risk of shock to a person or
persons.
◊ Exclamaon point symbol: the exclamaon point within an equilateral triangle symbol is intended
to alert the user to the presence of important operang and maintenance (servicing) instrucons
in the literature accompanying the product.
»WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
»Use the mains plug to disconnect the apparatus from the mains.
»THE MAINS PLUG OF THE POWER CORD MUST REMAIN READILY ACCESSIBLE.
»Do not defeat the safety purpose polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of
your obsolete outlet. Cauon! To reduce the risk of electrical shock, grounding of the center pin of this plug must be
maintained.
»Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and the
point where they exit from the apparatus.
»Do not block the air venlaon openings. Only mount the equipment per Intelix’s instrucons.
»Use only with the cart, stand, table, or rack specied by Intelix or sold with the equipment. When/if a
cart is used, use cauon when moving the cart/equipment combinaon to avoid injury from p-over.
»Unplug this apparatus during lightning storms or when unused for long periods of me.
»Cauon! Shock Hazard. Do not open the unit.
»Refer to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

INT-HD52 Owners Manual
4
Table of Contents
Product Overview��������������������������������������������������������������������������������������������������������������������������������������� 6
Package Contents ��������������������������������������������������������������������������������������������������������������������������������������� 6
Front and Rear Panels��������������������������������������������������������������������������������������������������������������������������������� 7
Front Panel���������������������������������������������������������������������������������������������������������������������������������������������������� 7
Rear Panel����������������������������������������������������������������������������������������������������������������������������������������������������� 8
IR Remote��������������������������������������������������������������������������������������������������������������������������������������������������� 9
Installaon Instrucons���������������������������������������������������������������������������������������������������������������������������� 10
Quick Start ��������������������������������������������������������������������������������������������������������������������������������������������������10
Mount the Switching Scaler ������������������������������������������������������������������������������������������������������������������������10
Connecng Sources�������������������������������������������������������������������������������������������������������������������������������������10
HDMI / Display Port Input ....................................................................................................................10
VGA/Analog Video Inputs .....................................................................................................................10
Connecng Displays ������������������������������������������������������������������������������������������������������������������������������������11
HDMI Output ........................................................................................................................................11
HDBaseT Output ...................................................................................................................................11
Connecng Microphone Input ��������������������������������������������������������������������������������������������������������������������11
Connect Audio Output���������������������������������������������������������������������������������������������������������������������������������11
Connect IR Control ��������������������������������������������������������������������������������������������������������������������������������������12
Source Device and Scaler Control via Remote IR ..................................................................................12
Remote Display and Scaler Control via Local IR ....................................................................................12
Apply Power ������������������������������������������������������������������������������������������������������������������������������������������������12
Applicaon Diagram �������������������������������������������������������������������������������������������������������������������������������� 13
On Screen Display (OSD) Menu Navigaon ����������������������������������������������������������������������������������������������� 14
Opons Menu ���������������������������������������������������������������������������������������������������������������������������������������������14
Output Adjust .......................................................................................................................................14
Input5 Select ........................................................................................................................................14
Baud Rate .............................................................................................................................................14
User EDID Upload(USB) ........................................................................................................................14
Soware Update...................................................................................................................................14
Picture Menu�����������������������������������������������������������������������������������������������������������������������������������������������15
Picture Mode ........................................................................................................................................15
Color Temperature ...............................................................................................................................15
Aspect Rao .........................................................................................................................................15
Noise Reducon (HDMI Only) ..............................................................................................................15
Screen (VGA) ........................................................................................................................................15
Color Range (VGA) ................................................................................................................................15
Setup Menu�������������������������������������������������������������������������������������������������������������������������������������������������16
Setup Menu�������������������������������������������������������������������������������������������������������������������������������������������������16
OSD Language.......................................................................................................................................16
Restore Factory Default ........................................................................................................................16
Blending................................................................................................................................................16
HDMI CEC .............................................................................................................................................16
OSD Duraon ........................................................................................................................................16
Version ..................................................................................................................................................16

INT-HD52 Owners Manual
5
Web Graphical User Interface (GUI) Control���������������������������������������������������������������������������������������������� 17
Control Menu ����������������������������������������������������������������������������������������������������������������������������������������������18
Source ���������������������������������������������������������������������������������������������������������������������������������������������������������18
VGA .......................................................................................................................................................18
DP .........................................................................................................................................................18
VOLUME ...............................................................................................................................................18
POWER FUNCTIONS .............................................................................................................................18
Conguraon Menu������������������������������������������������������������������������������������������������������������������������������������19
Conguraon; Seng���������������������������������������������������������������������������������������������������������������������������������19
Output Resoluon ................................................................................................................................19
Update ..................................................................................................................................................19
Shutdown Timer (No Input) ..................................................................................................................19
Conguraon; Network ������������������������������������������������������������������������������������������������������������������������������20
Conguraon; Source Label������������������������������������������������������������������������������������������������������������������������20
RS232 Control Menu �����������������������������������������������������������������������������������������������������������������������������������21
Port .......................................................................................................................................................21
Baud Rate .............................................................................................................................................21
Command .............................................................................................................................................21
Password Menu ������������������������������������������������������������������������������������������������������������������������������������������22
Web Graphical User Interface (GUI) Update���������������������������������������������������������������������������������������������� 22
RS232 Commands������������������������������������������������������������������������������������������������������������������������������������� 23
Video Input Switching and Conguraon ���������������������������������������������������������������������������������������������������23
Video Input Customizaon��������������������������������������������������������������������������������������������������������������������������24
Video Input HDCP Compliance ��������������������������������������������������������������������������������������������������������������������24
Video Output Conguraon������������������������������������������������������������������������������������������������������������������������25
Video Output Adjustment ���������������������������������������������������������������������������������������������������������������������������25
Freeze Video Output������������������������������������������������������������������������������������������������������������������������������������26
Audio Input Conguraon and Adjustment ������������������������������������������������������������������������������������������������26
Audio Output Control����������������������������������������������������������������������������������������������������������������������������������26
CEC Setup and Control ��������������������������������������������������������������������������������������������������������������������������������27
Menu Navigaon ����������������������������������������������������������������������������������������������������������������������������������������27
OSD Visibility�����������������������������������������������������������������������������������������������������������������������������������������������27
System Query ����������������������������������������������������������������������������������������������������������������������������������������������28
System Query (connued)���������������������������������������������������������������������������������������������������������������������������29
System Power / Factory Default������������������������������������������������������������������������������������������������������������������29
Troubleshoong ��������������������������������������������������������������������������������������������������������������������������������������� 30
Presentaon Switcher does not power on ��������������������������������������������������������������������������������������������������30
No video from HDBaseT output ������������������������������������������������������������������������������������������������������������������30
Distorted or no video output�����������������������������������������������������������������������������������������������������������������������30
Cannot hear HDMI input audio�������������������������������������������������������������������������������������������������������������������30
Presentaon Switcher does not automacally switch ��������������������������������������������������������������������������������30
Technical Specicaons ���������������������������������������������������������������������������������������������������������������������������� 31

INT-HD52 Owners Manual
6
The Intelix INT-HD52 is a compact auto switcher scaler that allows the integraon of analog and digital devices
into a high-denion environment. Mounng opons include under table or resng on a shelf.
The INT-HD52 allows selecon of ve dierent sources, and will simultaneously scale the selected video to
HDMI and HDBaseT outputs. The unit features three HDCP compliant HDMI inputs, one Display Port input
and one VGA input. The VGA input can be congured to support YPbPr (component), YC (S-video), and C
(composite) video formats with the appropriate VGA breakout cable. There are eight xed output resoluons
to choose from, and several aspect rao modes, which will ensure your content is displayed properly. The
HDBaseT output will allow you to extend audio, video, and control signals up to 70m away.
The INT-HD52 oers unique audio opons designed to simplify your installaon. All audio inputs are embedded
into the HDMI and HDBaseT streams, so you can use your display speakers for audio. Addionally, the balanced
stereo audio output can be used for audio reinforcement. A balanced input is provided (line or microphone
level) which is mixed with the source audio to provide voice li capabilies; while the volumes of the mic and
source can be individually controlled.
The INT-HD52 can be controlled in many dierent ways. When the VGA input is dened as a PC signal input,
the INT-HD52 can be congured to automacally switch to an input once connected to the switcher; once a
device is removed, INT-HD52 will switch to the rst acve input with HDMI inputs taking priority. The front
panel oers source selecon and volume control. Third party control systems can ulize RS232 or Ethernet
ports on the rear panel, RS232 extended (with a compable HDBaseT receiver with RS232 throughput), and
rear panel IR control. CEC enabled source and display devices can also be controlled from the INT-HD52..
Product Overview
Package Contents
• (1) Intelix INT-HD52 Switcher Scaler
• (2) Mounng Ears with 4 Screws
• (1) Power Adapter (24VDC, 2.71A)
• (4) Plasc Cushions+
• (1) IR Remote
• (1) VGA Analog Breakout Cable (VGA to YPbPr)
• (1) RS232 DB9 - 3 Pin Phoenix Breakout Cable
• (2) 3 Pin Phoenix Connectors
• (1) 5 Pin Phoenix Connector
• (1) IR Emier
• (1) IR Receiver
• (1) Quick Install Guide

INT-HD52 Owners Manual
7
Front and Rear Panels
Front Panel
12 3 4 5 6
8 9 10
7 8 7
1. Built in IR Receiver
2. Power Indicator - GREEN when device is in standby mode, RED when device is powered on and no indicator when there is
no power to device
3. 1-HDMI/MHL input selector and acvity LED / Le Key for On screen display control (OSD)
4. 2-HDMI input selector and acvity LED / Right Key for OSD
5. 3-HDMI input selector and acvity LED / Up Key for OSD
6. 4-Display Port input selector and acvity LED / Down Key for OSD
7. 5-VGA input selector and acvity LED / Enter Key for OSD
8. Auto Switching selector and acvity LED- Press this to enter / exit auto-switching mode / OSD menu buon
• NOTE: When you set the VGA input port to C-Video or YPbPr in Manual-switching mode, the system will not be able to enter
auto-switching mode.
•Hold this buon down for 3 seconds to enter On Screen Display menu (OSD)
9. Volume knob for variable audio control- Push knob in to toggle between ‘Mic’ and ‘Source’ control

INT-HD52 Owners Manual
8
Rear Panel
1
3 4
2
5 6
1. INPUTS
•Video input ports: 1 HDMI/MHL, 2 HDMI inputs, 1 Display Port and 1 VGA
•Audio input ports: 1 Display Port external audio input and 1 VGA auxiliary audio input
2. OUTPUTS
•HDMI output: HDMI video output port
•HDBaseT output: Supports PoH. Connect to a compable HDBaseT receiver to transmit A/V, IR and RS232 control
3. MIC INPUT
•Mic audio port connects to microphone
•Dial switch- switches between 3 dierent modes; 48V for condenser mics, MIC mode for dynamic mics and LINE mode for
line level audio
4. CONTROL
•RES RESET - press this to reset output resoluon to 720p or to acvate HDMI and HDBT outputs if they have been turned o
•IR IN / IR OUT - connect with IR receiver and emier to control devices via IR
•FIRMWARE - Type-A USB port for updang rmware
•RS232 - Serial port, connect a control device to control the INT-HD52
•TCP/IP - Ethernet port, connect a control device or computer to control INT-HD52
5. AUDIO OUTPUT
•Stereo balanced L/R audio output
6. DC 24V
•Locking power port, connect DC 24V power adapter

INT-HD52 Owners Manual
9
IR Remote
The included IR remote performs all of the funcons available on the front panel.
The remote control requires two AAA baeries, which are included.
8
2
1
3
4
5
6
7
1. Power on/o
2. Input source select buons
3. Enter / Exit audio switching mode
4. Audio mute
5. Volume - Aer pressing this buon a volume
adjustment screen will shown on display
connected to INT-HD52, then press UP/DOWN to
adjust volume
6. Navigaon. OK = enter or conrm
7. Exit: terminates current operaon
8. OSD menu, also returns to previous menu

INT-HD52 Owners Manual
10
Installaon Instrucons
Quick Start
Mount the Switching Scaler
1. Mount the switching scaler
2. Connect sources
3. Connect displays
4. Connect microphone input (oponal)
5. Connect audio output (oponal)
6. Connect control (oponal)
7. Apply power
At least 2 inches of free air space is required on both sides of the INT-HD52 for proper side venlaon. Avoid
mounng the INT-HD52 near a power amplier or any other source of signicant heat.
For shelf mounng, aach the supplied shelf feet to the boom of the INT-HD52.
For table mounng, aach the supplied mounng rails to the sides of the INT-HD52. Once the rails are installed,
the scaler is ready to be mounted under a table.
VGA/Analog Video Inputs
Connect the source devices to VGA inputs using VGA cables that are less than or equal to 5 meters in length.
For source devices that are further away, a VGA extension device will be required to complete the connecon.
Use the supplied adapter cable (FLX-RBOCA) if the source is an analog video signal such as component or
composite video (yellow connector on source to red connector on FLX-RBOCA).
Connect the source devices to HDMI or Display Port inputs using HDMI / Display Port cables that are less than
or equal to 5 meters in length. For source devices that are further away, an extension device will be required
to complete the connecon.
Connecng Sources
HDMI / Display Port Input

INT-HD52 Owners Manual
11
L+
L-
R+
R-
L+
L-
R+
R-
Connecng Displays
HDMI Output
Connect the display devices to HDMI outputs using HDMI cables that are less than or equal to 5 meters in
length. For display devices that are further away, it is highly recommended to ulize the HDBaseT output.
For all HDBaseT cabling, the EIA/TIA-568B crimp paern must
be used on Category 6 or greater cable. In areas with large
amounts of electromagnec (EM) or radio frequency (RF)
interference, a shielded variety of Category 5e or greater cable
is recommended with shielded connectors on both ends of the
selected cable.
The HDBaseT output provides 15 was of Power over Ethernet,
which eliminates the need for a power supply with a compable
HDBaseT receiver. Intelix recommends using the DIGI-HD60C-R
or DIGI-HD60-R for installaons which require remote power.
TIA/EIA-568B
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
1 8
Connect the HDBaseT receiver to the display per the manufacturer’s instrucons. Connect the HDBaseT cable
to the scaler and the HDBaseT receiver.
HDBaseT Output
Connecng Microphone Input
Insert the removable 3-pin phoenix connector block to the MIC input.
Set the MIC switch to the proper seng for the microphone input source.
48V 48V phantom power
MIC No phantom power
LINE No gain needed
Connect Audio Output
Insert the removable 5-pin phoenix connector block to the audio output. The INT-HD52 supports a stereo
balanced le and right output.

INT-HD52 Owners Manual
12
Connect IR Control
Source Device and Scaler Control via Remote IR
Aach the plasc end of the IR emier to the IR receiver of the source device. Insert the TS 3.5 mm plug of the
emier to the IR output port (IR OUT) of the switching scaler for the source device to control.
The INT-HD52 has an advanced bidireconal IR control protocol through the HDBaseT output port, which
allows for the control of the sources, displays, and presentaon switcher. Intelix recommends using the INT-
HD70-RX or the DIGI-BSR-4K for installaons which require IR extension.
Only use the included IR receiver and emier and transmier. Third party 12V DC IR components are not
compable with the INT-HD52.
An IR signal passed from the display locaon through the HDBaseT connecon can provide control of the
source device. The IR signal from the remote display locaon can also control the switching of the switcher /
scaler.
Remote Display and Scaler Control via Local IR
An IR signal may be passed to a remote display locaon through the HDBaseT connecon. In order to control
the INT-HD52 via IR or extend an IR signal to a remote display, the included IR receiver must be connected to
the IR input port (IR IN) of the switcher / scaler.
Apply Power
Plug the power supply into the power input port on the rear of the switcher / scaler. Twist the locking ring
clockwise to prevent accidental disconnecon of power.

INT-HD52 Owners Manual
13
INT-HD52 5X1 PRESENTATION SWITCHER
REMOTE
MIC
CONTROL SYSTEM
AUDIO AMPLIFIER
PROJECTOR
INT-HD70-RX
HDBT RECIEVER
(Not Included)
DISPLAY
LEGACY
COMPUTER
WIRELESS
BYOD
DVD
LAPTOP
WIRED
BYOD
HDMI
CATx
DP
VGA
AUDIO
IR
RS232
up to 70m / 230’
Applicaon Diagram

INT-HD52 Owners Manual
14
On Screen Display (OSD) Menu Navigaon
The menu system of the INT-HD52 provides a wide array of opons to customize the installaon of the product
regardless of customer needs.
Upon entering the menu, navigang le or right will provide three dierent sub-menus: Opons, Picture and
Setup. Pressing ENTER on the front panel or OK on the remote will cycle through opons or enter another
menu if mulple conguraon sengs are available.
Opons Menu
Output Adjust
Input5 Select
Baud Rate
Soware Update
Selecng Output Adjust will open another menu which will change the vercal / horizontal posion, width, and
height of the output image. The default value is O. Pressing right or le will cycle to On. Values range from 0
to 100. Pressing MENU will exit the sub-menu.
HDMI and HDBasetT output ports can also be turned ON/OFF under this menu seng.
Pressing ENTER or OK will cycle the analog video input modes: VGA, YPbPr (component video), and AV
(composite video).
Pressing ENTER or OK will allow you to change the baud rate seng of the RS232 control.
A separate document will provide usage instrucons once a new soware update is available.
User EDID Upload(USB)
Load user dened EDID table into switcher / scaler through this menu. You will need to have the EDID table
saved on to a portable USB drive to use this feature. Portable USB drive will use the rmware USB port on the
INT-HD52 to upload the EDID table.

INT-HD52 Owners Manual
15
Picture Menu
Picture Mode
Color Temperature
Aspect Rao
Noise Reducon (HDMI Only)
Selecng Picture Mode will open another menu which will change the contrast, brightness, color, and sharpness
of the input image. The default value is Standard. Values range from 0 to 100. Pressing MENU will exit the sub-
menu.
Selecng Color Temperature will open another menu which will change the color temperature of the input
image. The default value is Medium. Values range from 0 to 100. Pressing MENU will exit the sub-menu.
Selecng Aspect Rao will open another menu which will change the aspect rao of the input image. The
default value is Nave. While VGA only has three aspect rao selecons available, HDMI has seven. Pressing
MENU will exit the sub-menu.
VGA and HDMI: Nave, 4:3, 16:9
HDMI only: Zoom 1, Zoom 2, Just Scan, Panorama
Selecng Noise Reducon will open another menu which will compensate for compression noise of
the input image. Available selecons are: O, Low, Middle, High, and Default. Pressing MENU will exit
the sub-menu.
Screen (VGA)
Selecng Screen will open another menu which will adjust the input signal processing to clear up various
analog distoron issues. Auto Adjust will automacally correct for any input signal issues. Manual adjustments
include Horizontal Posion, Vercal Posion, Size, and Phase where values range from 0 to 100. Pressing MENU
will exit the sub-menu.
Color Range (VGA)
Selecng Color range will cycle between two opons: 0-255 (deep color) and 16-235 (standard color).

INT-HD52 Owners Manual
16
Setup Menu
Setup Menu
OSD Language
Blending
HDMI CEC
OSD Duraon
The Setup menu features on-screen display (OSD) language selecon, OSD blending (transparency), HDMI CEC,
and OSD duraon.
Selecng OSD Language will open another menu which will change the menu language of the INT-HD52.
The available languages are: English, German, Russian, Chinese, French, Spanish, and Swedish. The default
language is English. Pressing MENU will exit the sub-menu.
Selecng Blending will open another menu which will present opons the menu transparency. The available
opons are O, Low, Middle, and High where the default is O. Pressing MENU will exit the sub-menu.
Selecng HDMI CEC will open another menu which will present opons to adjust the operaon of CEC. Device
List will show which HDMI devices support CEC. Cycling HDMI CEC in the sub-menu will turn on or o CEC
support. Cycling Auto Standby will enable or disable this feature. Pressing MENU will exit the sub-menu.
Selecng OSD Duraon will open another menu to select the period of me the input name will be visible aer
switching sources. Available mes are O, 5Sec, 10Sec, and 15Sec. The default is O. Pressing MENU will exit
the sub-menu.
Restore Factory Default
This menu will allow you to reset the INT-HD52 back to factory default
Version
Displays current soware

INT-HD52 Owners Manual
17
Web Graphical User Interface (GUI) Control
The INT-HD52 can be controlled by web-based GUI which allows users to interact the INT-HD52 through
graphical icons and visual indicators.
Connect a computer and the INT-HD52 to a Ethernet switch using the Ethernet ports on your
computer and the INT-HD52. Type 192.168.0.178 in a web browser on the computer to access the
web GUI. When prompted enter ‘user’ as the user name and password and clock LOGIN.

INT-HD52 Owners Manual
18
Control Menu
Source
VGA
VOLUME
POWER FUNCTIONS
Click on desired video input source
Click ADJUST to adjust the posion of the VGA output image
Click SOURCE to turn on/o source device
Click DISPLAY to turn on/o display device
Click LOCAL to put the INT-HD52 into standby mode
DP
Click the corresponding posive / negave buons to increase / decrease the volume of the microphone or
source audio input. Click the corresponding MUTE buon to mute / unmute microphone or source audio input.
Click AUDIO to turn on/o the Display Ports external audio input

INT-HD52 Owners Manual
19
Conguraon Menu
Click on the in the control menu to access the conguraon menu. The conguraon menu oers three
sub-menus; Sengs, Network and Source Label.
Select the desired output resoluon and click CONFIRM
Output Resoluon
Conguraon; Seng
Insert a portable USB drive containing the EDID / rmware le into the FIRMWARE port on the INT-HD52 then
click EDID or FIRMWARE to update
Update
If the INT-HD52 does not detect a present video signal it will automacally shut down aer the preset me
interval has passed. AUTO drop down menu sets the me interval for auto switching mode and MANU drop
down sets the me interval for manual switching mode
Shutdown Timer (No Input)

INT-HD52 Owners Manual
20
In this menu you can change the IP address of the INT-HD52. Select DHCP if you desire the IP to be set
automacally based on your DHCP network sengs or select STATIC IP mode to manually enter in the IP
Address, Subnet Mask and Gateway. When you manually enter in the IP address make sure you the address
does not overlap an exisng IP address in the same network.
Conguraon; Network
Conguraon; Source Label
In this menu you can change the name of the source inputs as desired.
Other manuals for INT-HD52
1
Table of contents
Popular I/O System manuals by other brands

RC Electronics
RC Electronics Snipe manual

turck
turck BL20 user manual

WoMaster
WoMaster LoRa LM100 user manual

Moxa Technologies
Moxa Technologies ioLogik E2212 user manual

Altec Lansing
Altec Lansing 1781A 1781AT SIGNAL PROCESSING manual

Tiancheng Fire Protection Equipment
Tiancheng Fire Protection Equipment TCSG5270 user manual