Inter-fab 15' GARDEN RIDE SLIDE Programming manual

GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
15’ GARDEN RIDE SLIDE
Assembly & Installation Instructions
15’ GARDEN RIDE SLIDE
ATTENTION INSTALLERS
THESE INSTRUCTIONS MUST
REMAIN WITH THE SLIDE OWNER!
PLEASE DELIVER AND REVIEW THIS
MANUAL WITH THE HOMEOWNER.
S.R.SMITH 3050 S. ALVERNON WAY • TUCSON, AZ 85713
520.790.7040 • 800.737.5386 • FAX [phone] • interfab.com
IMPORTANT INSTALLATION INFORMATION
The installation of this product should be done only by a licensed and professional installer. Installation should
be done strictly in conformance with all local building codes, electrical codes and other building and safety laws
and regulations. Among other things, that your installer should carefully analyze the need to bond the product
to prevent an electrical hazard. Failure to properly install this product could result in a dangerous condition,
including but not limited to electrical or structural hazards. S.R.Smith, LLC disclaims all liability arising from
the installation and the user assumes all risk associated with the installation.
WARNING

GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
WARNING IMPORTANT INSTALLATION INFORMATION
The installation of this product should be done only by a licensed
and professional installer. Installation should be done strictly
in conformance with all local building codes, electrical codes
and other building and safety laws and regulations. Among other
things, that your installer should carefully analyze the need to
bond the product to prevent an electrical hazard. Failure to
properly install this product could result in a dangerous condition,
including but not limited to electrical and or structural hazards.
S.R.Smith disclaims all liability arising from the installation and
the user assumes all risk associated with the installation.
For Technical Support or Assistance,
Contact Customer Service at:
S.R.SMITH
3050 S. ALVERNON WAY
TUCSON, AZ 85713
[phone]
or visit www.interfab.com
To obtain complete copies of the ANSI/APSP/ICC-5 2011
Standard for Residential Inground Pools or to obtain copies of
“The Sensible Way to Enjoy Your Inground Swimming Pool”
contact:
The Association of Pool & Spa Professionals (APSP)
2111 Eisenhower Ave.
Alexandria, VA 22314
[phone]
or visit www.theapsp.org
WARNING

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
1
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
TABLE OF CONTENTS
Intended Use Instructions ........................................................2
Water Safety Envelope.............................................................3
Slide Placement/Deck Requirements......................................4-5
Slide Measurements ...............................................................6
Slide Components ...................................................................7
Installing Landing Pads ............................................................8
Connecting Flumes..................................................................8
Connecting Handrails...............................................................9
Using Optional Support System .................................................9
Pre-Assemble Foot Receivers..............................................9
Attach Leg Supports to Landing Pads ................................10
Place Slide in Position .................................................10-11
On-Deck Installation .........................................................11
In-Deck Installation...........................................................12
Attach Water Supply........................................................12
Slide Care & Maintenance......................................................13
S.R.Smith Limited Warranty...................................................14

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
2
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
1. Everyone who uses this slide must know, understand and follow these instructions
2. The ANSI/APSP/ICC-5 2011 standard for above ground pools prohibits the use of slides or diving boards
on above ground pools.
3. This slide should never be installed on above ground pools, ponds, floating docks or platforms, boat docks
or houseboats or any natural body of water.
4. Be familiar with the shape and depth of the pool before you slide. This slide should only be used with the
proper water safety envelope, as described in Diagrams A, B & C on page 3 and in accordance with the
slide positioning diagrams on pages 4.
5. Because the slide may only be used in water 4.5’ deep or greater, all slide users must be able to swim
in deep water.
6. Weight limit for this slide is 350 pounds, no slider weighing more than 350 pounds may use this slide.
7. The surface of the slide is very slippery when wet; USE CAUTION when entering the slide and when
transitioning from standing to sitting.
8. Slide in a feet first sitting position ONLY.
9. IMPORTANT: sliding headfirst is prohibited: serious spinal injury resulting in paralysis or death can result.
10. Maintain adult supervision at all times.
11. Only one person at a time is allowed on the slide.
12. Be sure the water delivery system is on and lubricating the slide prior to use.
13. Collision with another swimmer or a diver can result in serious injury or death for one or both persons:
Before sliding, always make sure that the path in front of the slide is free from any (including submerged)
obstructions including other people or objects in the pool such as rafts, inner tubes etc. When a diving
board is also present, make sure you do not use the slide while someone is on or using a diving board.
Take turns.
14. No roughhousing or horseplay should be allowed on the slide at any time.
15. Do not stand, jump or dive from any part of the slide.
16. Do not slide on objects such as rafts or inner tubes. doing so greatly increases your risk of injury.
17. Do not slide through or at objects such as rafts or inner tubes, doing so greatly increases your risk of
injury.
18. Do not use this slide if physically impaired or handicapped without your doctor’s permission.
19. Do not use this slide with a history of heart conditions, seizures, back problems, fainting or fear of
heights.
20. Do NOT use this slide if you are pregnant.
21. Do not drink alcohol and use this slide.
22. Don’t take chances, inspect the slide at least once a year (see the slide inspection list on page 16, do
not use the slide if any part becomes loose, damaged, weakened or broken. If necessary, before using
the slide again, have it inspected and repaired by a competent professional familiar with pool slides.
SLIDE IN A SITTING
POSITION ONLY
Face forward on the slide, holding the legs and arms
with the palms of your hands forward and tilted up.
WARNING SERIOUS INJURY OR DEATH CAN RESULT FROM THE
IMPROPER INSTALLATION OR USE OF THIS SLIDE.
When installed according to these instructions, this slide conforms to
Consumer Product Safety Standard Guidelines.
DO NOT SLIDE HEAD FIRST SERIOUS INJURY
CAN RESULT DEEP WATER SWIMMERS
ONLY
INTENDED USE
INSTRUCTIONS
WARNING

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
3
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
DIAGRAM A
(NOT TO SCALE)
DIAGRAM C
(NOT TO SCALE)
Minimum Water Safety Envelope
DIAGRAM B
(NOT TO SCALE)
Minimum Slide
Clearance Area
ALL SLIDES SHOULD
BE BONDED
Check your local electrical
code requirements.
WATER SAFETY ENVELOPE
A minimum water depth of three feet (3') under the exit
of the slide which increases to a depth of four feet six
inches (4'6”) at point A which is located four feet six
inches (4'6") from the back wall of the pool. A minimum
depth of four feet six inches (4'6”) must be maintained
at a distance of nine feet (9') along the centerline of the
slide from point A. The above described water depth
profile shall extend a minimum of three feet six inches
(3'6") on either side of the centerline of the slide.
(See Diagrams A, B & C)

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
4
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
SLIDE PLACEMENT
If the slide meets the pool edge at an angle, then the outside curve “Pivot A” has to be at
the pool edge. Refer to Diagram D & E below.
If the slide meets the pool edge straight on, then the end of the exit section should be parallel
with the pool edge. Refer to the Diagram F below.
NOTE The exit point of the flume can be no higher than 20” above the water.
DIAGRAM D
(NOT TO SCALE)
DIAGRAM E
(NOT TO SCALE)
DIAGRAM F
(NOT TO SCALE)
3” MINIMUM
OVERHANG
3” MINIMUM
OVERHANG
3” MINIMUM
OVERHANG

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
5
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
MINIMUM DECK REQUIREMENTS
DIAGRAM G
(NOT TO SCALE)
DIAGRAM H
(NOT TO SCALE)
GRS 15’ Slide
Left Turn
GRS 15’ Slide
Right Turn

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
6
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
MEASUREMENTS 15’ GRS LEFT TURN
LEFT TURN WITH SUPPORTS LEFT TURN WITHOUT SUPPORTS
LEFT TURN HEIGHT
MEASUREMENTS 15’ GRS RIGHT TURN
RIGHT TURN W SUPPORTS RIGHT TURN WITHOUT SUPPORTS
RIGHT TURN HEIGHT

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
7
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
SLIDE COMPONENTS ANCHOR COMPONENTS
15’ Garden Ride Slide Series 15’ Optional Support System
Centerline Length: 194” Exit Section Support: 14”
Starting Elevation: 73 1⁄8” Mid Section Exit Support: 23 ¾”
Flume Width: 28” Flume to Flume Support: 39 ¼”
Flume Depth: 15” Mid Section Entry Support: 54”
Water Flow (GPM): 40 Entry Section Support: 72 ¾”
Entry Section: 1 Flanged Feet: 10
Exit Section: 1 3/8 Wedge Anchors 30
Handrails: 2
Entry Mid Section
Landing Pad: 1
Exit Mid Section
Landing Pad: 1
Flume to Flume
Landing Pad: 1
lnter-Fab recommends using the Garden Ride Slide Optional Support System for the
•installation. The Optional Support System ensures proper installation of the slide. lnter-Fab
does not warrant damage caused by installations of the Garden Ride Slide installed without
the support system.Please read Limited Warranty on page 14 of installation manual.
It is highly recommended that provision be made for future maintenance and/or removal
•of the slide from the substrate, if necessary. Do not fully encase the slide in concrete
or permanently fixed structure/material.
Do not construct objects or formations along or over the slide pathway that obstruct the• pathway for sliders or cause potential harm to the head, arms or legs. Minimum recommended
head clearance above the slide pathway is 7 feet.
Minimum Garden Ride Slide water envelope is 7' wide (centered on slide) x 13.5' long x• 4.5' deep.
The exit section must be installed with the correct alignment to the pool edge with a minimum
•overhang of 3" and should be supported at the fiberglass landing plate.
Zoom Flume water delivery system requires a 1" PVC flex hose. For best performance, the
•recommended water flow at the slide is 20-40 GPM, connecting a ball valve in line is
recommended for water flow adjustment. NOTE Connect the Zoom Flume water
delivery system to water source and test for leaks or defects prior to final assembly/
installation.
See page 13 of installation manual for Garden Ride Slide Care and Maintenance.•
S.R.Smith reommends that you read the
Garden Ride Slide Installation Manual in
its entirety before attempting an installation.
IMPORTANT NOTICES:

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
8
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
15’ GARDEN RIDE SLIDE ASSEMBLY
INSTALLING LANDING PADS:
Using cardboard to place under the slide sections so as not to damage the finish; lay both
the upper and lower flume sections upside down. Each flume section has a yoke support
that requires attachment of a 90 Landing Pad. (See Figure 1) Install pad on the side of
flange towards pool, attach the Upper and Lower Landing Pads to the Mid Section Supports
(Exit and Entry) using 3/8” x 11⁄2” stainless steel bolt, flat washer, lock washer and nut.
Make ure to u e the provided Anti-Seize on all hardware.
NOTE The two Yoke Landing Pads have four ( 4 ) attachment holes and the single
Flume to Flume Landing Pad has three ( 3 ) attachment holes. (See Figure 2)
Fig. 1 Fig. 2
CONNECTING FLUMES:
NOTE Temporarily connect the Zoome Flume™ water delivery system to a water
source and test for leaks or defects prior to assembly/installation.
Align the two flume sections and line up the Center Landing Pad along the upper flume
flange, using the provided 3/8” stainless steel hardware, place a flat washer on the 3/8”
x 13⁄4” bolt and push the bolt and the two flume sections and landing pad on pool side of
flange, secure with the other flat washer, lock washer and nut. (See Figure 3) Make ure
to u e the provided Anti-Seize on all hardware. Hand tighten all seven flange bolts. With
a minimum of three ( 3 ) persons, turn the slide sections over. Check that the two flumes
are aligned correctly by running your hand along the sliding surface. You want to ensure a
smooth transition between the two sections, adjust sections as needed. When both are
aligned properly, utilizing a torque wrench, tighten each nut to approximately half of the maximum
25 ft. lbs. Tighten the bolts in an alternating fashion working from Left to Right starting
with the center bolt, working your way up the flange. (See Figure 4) Tightening the bolts in
this sequence is necessary to compress the gasket evenly.
Repeat the same tightening process until the specified 25 ft. lbs. is reached at each bolt.
DO NOT OVER TIGHTEN. Using greater force may fracture the fiberglass.

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
9
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
Fig. 3 Fig. 4
Fig. 5
INSTALLATION GUIDE FOR 15’ GARDEN RIDE SLIDE
USING OPTIONAL SUPPORT SYSTEM:
The GRSS Optional Support System is to be used on a flat grade concrete surface; for in-deck
or on-deck installation. For a 15’ GRSS (both Left and Right turn) the recommended minimum
deck area: 12’ 3” x 9’ 10” x 4”
The Optional Support System is designed to easily orient the slide to ensure proper elevation
starting at the entry section 731⁄8” to the exit section at 12” above the deck.
PRE-ASSEMBLE FOOT RECEIVERS:
Attach a deck anchor to each leg support with a 2 ½” x ¼” stainless steel bolt, flat washer,
lock washer and nut as shown. (See Figure 6) Hand tighten only.
CONNECTING HANDRAILS:
Install the handrails (See Figure 5) for the correct orientation, use the provided 3/8” x 1”
stainless steel bolt, flat washer and lock washer to attach - do not over tighten.

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
10
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
ATTACH LEG SUPPORTS TO LANDING PADS:
While the slide is still upside down, you may attach the short legs to the Exit Section Landing
Pad which is pre-drilled to accept the bracket. Make ure to u e the provided Anti-Seize
on all hardware. Place the provided 3/8” flat washer on a 3/8” x 11⁄2” stainless steel bolt,
from the underside of the Exit Section Landing Pad through the stainless steel leg bracket,
place a flat washer, lock washer and nut to secure. (See Figure 7) Repeat the process for
the other three pre-drilled holes. Hand tighten only.
With the help of others, you will now flip the slide right side up. Have two people lift up and
hold the Entry Section and attach the Entry Support Legs to the Entry Section Landing Pad.
Use Anti-Seize and Hand tighten only. Work your way down the slide and attach all
remaining Support Legs.
Fig. 6 Fig. 7
Fig. 8A – 15’ GRS Left Turn Fig. 8B – 15’ GRS Right Turn
PLACE SLIDE IN POSITION:
Using three to four people, gently move the fully assembled slide to its correct and final position
on the deck. The Exit Section should be placed so all water runs into the pool, the minimum
overhang is 3”. The front leg(s) cannot be positioned any closer to the water’s edge than
12”. (See Figures 8A & 8B)
GRID INCREMENTS IN FEET
GRID INCREMENTS IN FEET

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
11
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
ON-DECK INSTALLATION:
Using the deck anchor flanges as a template, mark the locations for the anchor bolts. Gently
move the slide to one side. Using a 3/8” masonry drill bit and a hammer drill, drill holes
13⁄4” – 2” deep, make sure you drill to the correct depth and make sure not to drill all the way
through the deck. Clean debris from holes using a shop vacuum or garden hose. Reposition
the slide and align the anchor flanges to the holes. Place a 3/8” wedge anchor through the
anchor flange into each hole, and gently hammer the bolt into the deck leaving ¾” – 1” of the
bolt above the anchor flange – make sure the anchor goes in straight. Put anti-seize on the wedge
anchor, then the flat washer, lock washer and nut. Secure the nuts on the bolts but do not
over tighten. (See Figure 10)
Fig. 10
93⁄16”
Deck Anchor
Hole A
Deck Line
FINAL TIGHTENING OF ALL CONNECTIONS:
Tighten the ¼” bolts from Leg to Deck Anchor. Move to the bottom of the slide and tighten
all Leg Supports to their Landing Pads.
Fig. 9
Once placement has been determined, starting from the Exit Section, align leg supports
using a bubble level ensure both legs are straight (plumb). (See Figure 9) Hand tighten the
leg supports to the Landing Pads. Work your way up the slide until all leg supports had
been tightened and all legs are plumb.

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
12
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
IN-DECK INSTALLATION:
Attach slide legs to the higher of the 2 bolt holes on the deck anchor “hole B”, make a mark
with a marking pen or duct tape 41⁄4” from the bottom of the deck anchor, shim the legs so
the mark you made on the deck anchor is flush with the finished deck, using a bubble level
ensure the legs are plumb. Pour concrete to secure legs, ensure the proper footing depth is
maintained under the deck anchor. (See Figure 11)
ATTACH WATER SUPPLY TO SLIDE:
Your Garden Ride Slide is equipped with a 1” Female Slip adapter. A dedicated 1½” water stub
up should be plumbed to your slide location. We recommend you plumb the slide with 1” PVC
flex hose using a reducer to connect to the stub up. For best performance, the
recommended water flow at the slide is 20-40 GPM.
Glue and slip the 1” PVC flex hose into the 1” female fitting on the underside of the Entry Section.
(See Figure 12) Use PVC primer and glue (not included) as required. A ball valve is recom-
mended to allow the water flow to be adjusted.
Fig. 11
93⁄16”
Deck Line
Deck Anchor
Concrete
Deck
41⁄4”
3”
3 4”
Fig. 12

INSTALLATION INSTRUCTIONS 15’ GRS SLIDE
13
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
GARDEN RIDE SERIES SLIDE CARE & MAINTENANCE
Your Garden Ride slide requires periodic maintenance to keep it looking like new and protected
from the elements.
• Wash slide monthly or more frequently if needed using a mild soap and soft cloth. Keep
cleaning materials from entering pool.
Do not use abrasive cleaners, bleaches, chorines, high alkaline or strong acidic• cleaners.
Do not use steel wool, wire brushes, metal scrapers, Scotch Brite or other• abrasive sponge pads.
• Keeping your slide’s gel coat finish coated with wax – starting when the slide is new – is the
best way to prolong its life.
Choose a wax intended for use on gel coat surfaces. Preferably one designed for• use in a Marine environment.
Test product on small inconspicuous section of slide prior to full application.•
While application instructions will vary between brands of wax, in general you apply• the wax with a cloth or foam pad using circular motion. Once wax dries to a haze,
buff the excess with a soft dry cloth.
Routine waxing (at least twice a year) will maintain the smooth reflective surface of• your slide.

S.R.SMITH LIMITED WARRANTY
14
GRS15-IM Rev. 9/18 (SBK-GRS15 INST)
LIMITED WARRANTY
Build Your Own Slide 1 (BYOS 1), Build Your Own Slide 2 (BYOS 2),
Garden Ride Series Slides (GRS7/GRS10/GRS15), and
River Run Slides (19A/19B/23A/24A/24B/29A)
One (1) Year Limited Warranty
What is covered by this warranty? S.R.Smith, LLC warrants all products it manufacturesto be free from
defects in materials and factory workmanship for a period of 12 months. This warranty begins from the date
of retail purchase and extends to the original retail owner. This warranty is contingent upon the proper use
and care of the equipment. S.R.Smith agrees to repair or replace, at its sole discretion, any product that fails
to perform as specified. This warranty relates only to defects in materials and workmanship.
What is not covered by this warranty?
• This warranty is not enforceable by any party other than the original retail owner.
• This warranty does not extend beyond the period of 12 months.
• Refer to Garden Ride Slide Care and Maintenance instructions for regular maintenance and cleaning. Normal
wear and tear, chemical damage, discoloration, misuse, fading of materials, microbiological staining and rust
or corrosion of any metallic parts, and any other physical damage are not included in this warranty. This warranty
does not cover equipment that has been modified or has been subjected to abusive physical or environmental
stresses. This warranty also does not include damage or failure resulting from other causes, including, but
not limited to acts of God, misuse or abuse, accident or negligence, fire, improper installation or ice damage.
• In the event that products are altered or repaired by anyone without the prior written approval of S.R.Smith,
all warranties are voided.
• S.R.Smith shall not be responsible for the cost of removal or replacement of any defective product, nor for
any other expenses such as loss of time, inconvenience, incidental expenses, telephone calls, labor
, material
charges, or travel incurred in connection with the removal or replacement of such product.
IMPORTANT NOTE FOR GARDEN RIDE SLIDES S.R.Smith, LLC offers a support and anchor system
(Garden Ride Slide Optional Support System) for the Garden Ride Slide Series which is sold separately.
S.R.Smith recommends that anyone installing a Garden Ride Slide Series slide use this anchor and support
system to help ensure proper installation of the slide. S.R.Smith does not warrant damage caused to
Garden Ride Slide Series slides installed without the Garden Ride Slide Optional Support System and
disclaims any liability resulting from such installations. The pool owner shall look solely to the installer
for resolution of any issues arising as a result of installations not utilizing the Garden Ride Slide
Optional Support System.
How to make a warranty claim
Visit www.interfab.com and click on the “File a Warranty Claim” link. You must fill out all required fields in the
form and include all required documentation.
3050 S. ALVERNON WAY TUCSON, AZ 85713
520.790.7040 800.737.5386 FAX [phone] INTERFAB.COM