International Concepts WR-3048X User manual

ITEM NO.: WR-3048X
ISSUED JAN 22, 2018
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
:X-SIDE WINE RACK 30X48
: WR-3048X

ITEM NO.: WR-3048X
ISSUED JAN 22, 2018
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: WR-3048X
ISSUED JAN 22, 2018
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Side frame
(L-R)
2
C
Shelf
1
D
Shelf
1
E
Front rack
3
F
Back rack
3
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 30mm)
12
2
Flat Washer
(ɸ6.5 x 13mm)
12
3
Lock Washer
(ɸ6.5 x 11mm)
12
4
Long Screw
(M4 x 35mm)
14
5
Short Screw
(M3.5 x 15mm)
4
6
Steel band
2
7
Allen key
(M4 x 30mm x 110mm)
1

ITEM NO.: WR-3048X
ISSUED JAN 22, 2018
Printed in Vietnam
- 4 -
STEP 1
Attach top (A), and shelves (C) and (D) to side frame (B) with bolts (1), and washers (3) and (2) as
shown below. Tighten with Allen key (7).
It
STEP 2
Attach racks (E) and (F) to side frame (B) with screws (4) as shown below. Tighten with a screwdriver.

ITEM NO.: WR-3048X
ISSUED JAN 22, 2018
Printed in Vietnam
- 5 -
STEP 3
Attach top (A), and shelves (C) and (D) to the other side frame (B) with bolts (1), and washers (3) and
(2) as shown below. Tighten with Allen key (7).
Attach racks (E) and (F) to the other side frame (B) with screws (4) as shown below. Tighten with a
screwdriver.

ITEM NO.: WR-3048X
ISSUED JAN 22, 2018
Printed in Vietnam
- 6 -
STEP 4
Attach steel band (6) to the unit with short screws (5) and attach the steel band to the wall with long
screws (4) as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.