Oneida Air Systems STZ180001 User manual

Rev: A 20221103LL Doc. #ZBI000013
Leg Kit
18" Stand/ 21"-23" Stand/ Extension
#STZ180001
#STZ212300
#STZ212301
INSTRUCTION SHEET
Actual appearance may vary to that shown above.

2
Oneida Air Systems
54-3/16"
1,376 mm
30-1/4"
769 mm
30-1/4"
769 mm
18" Stand Dimensions
Position 1
58-3/16"
1,478 mm
With Leg Extensions
For 35 gallon drum
and/or Universal
Drum Dolly
For 55 gallon drum
and/or Stacking
Sound Filter
For 55 gallon drum,
Universal Drum Dolly,
and/or Stacking
Sound Filter
Position 2
66-3/16"
1,681 mm
Position 3
70-11/16"
1,796 mm
Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.
The Angle Bracket Leg Extension Kit (#STZ212301) is included with 55 gallon drum systems. The Leg Extensions are required for the 35 gallon drum if you purchased the Universal Drum Dolly (#SDD990000) or the 13"
Stacking Sound Filter (#BSS131400).

3oneida-air.com
56"
1,422 mm
33-3/4"
769 mm
30-1/4"
769 mm
21-23" Stand Dimensions
Position 1
60"
1,524 mm
For 35 gallon drum
and/or Universal
Drum Dolly
For 55 gallon drum
and/or Stacking
Sound Filter
For 55 gallon drum,
Universal Drum Dolly,
and/or Stacking
Sound Filter
Position 2
68"
1,727 mm
Position 3
72-1/2"
1,842 mm
Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.
The Angle Bracket Leg Extension Kit (#STZ212301) is included with 55 gallon drum systems. The Leg Extensions are required for the 35 gallon drum if you purchased the Universal Drum Dolly (#SDD990000) or the 13"
Stacking Sound Filter (#BSS131400).
With Leg Extensions

4
Oneida Air Systems
Position 1
Position 1
Position 2
Position 3
Position 3Position 2
Leg Extension Dimensions
For 35 gallon drum
and/or Universal
Drum Dolly
For 55 gallon drum
and/or Stacking
Sound Filter
For 55 gallon drum,
Universal Drum Dolly,
and/or Stacking
Sound Filter
Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.
The Angle Bracket Leg Extension Kit (#STZ212301) is included with 55 gallon drum systems. The Leg Extensions are required for the 35 gallon drum if you purchased the Universal Drum Dolly (#SDD990000) or the 13"
Stacking Sound Filter (#BSS131400).

5oneida-air.com
ID PART # DESCRIPTION QTY
A STX212301 Lower Leg 4
B STX212303 Mid Brace 4
C STX001001 Stand Foot 4
18" STAND ONLY
D STX180002 Top Brace 4
E STX180001 18" Upper Leg 4
F AHX180001 18" Hardware Pack 1
F1 AFS156075 5/16-18 x 3/4" Carriage Bolt 40
F2 AFW180000 5/16" Flat Washer 40
F3 AFT900516 5/16 - 18 Nylock Nut 40
F4 RCP150001 Plastic Stand Foot 4
21-23" STAND ONLY
E STX212302 21-23" Upper Leg 4
F AHX212300 21-23" Hardware Pack 1
ID PART # DESCRIPTION QTY
21-23" STAND ONLY
F1 AFS156075 5/16-18 x 3/4" Carriage Bolt 24
F2 AFW180000 5/16" Flat Washer 24
F3 AFT900516 5/16 - 18 Nylock Nut 24
F4 RCP150001 Plastic Stand Foot 4
LEG EXTENSION ONLY
G STX212304 Leg Extension 4
B STX212303 Mid Brace 3
F AHX212301 Leg Extension Hardware Pack 1
F1 AFS156075 5/16-18 x 3/4" Carriage Bolt 24
F2 AFW180000 5/16" Flat Washer 24
F3 AFT900516 5/16 - 18 Nylock Nut 24
System Contents
A E
D
B G
C
FF1 F2 F3 F4
Please unpack the parts carefully and conrm you have
received each item listed here.
18" 21-23"

6
Oneida Air Systems
Assembly Instructions
FIG. 1
THE TELESCOPING STAND SHOULD BE INSTALLED ON A FLAT, STABLE BASE CAPABLE OF SUPPORTING THE WEIGHT OF THE ENTIRE SYSTEM (INCLUDING FULL WASTE CONTAINERS) ONCE ASSEMBLED.
1 If your system came with the leg extension,
choose what height position you want to use
[FIG. 1].
. Position 1: For 35 gallon drum with
Universal Drum Dolly.
. Position 2: For 55 gallon drum and/or
Stacking Sound Filter.
. Position 3: For 55 gallon drum, Universal
Drum Dolly, and/or Stacking Sound Filter.
Install onto a at, level surface. Leave
bolts loose initially and tighten once fully
assembled.
Note: We recommend that the stand be
assembled laying down and then raised into
position later on.
REQUIRED TOOLS RECOMMENDED TOOLS
9/16" Wrench Impact Driver Leveling Tool
9/16" Socket Wrench 2x4 Blocks
Torque Wrench
Note: You will need to supply your own mounting hardware if you wish to secure the Stand to the surface you are mounting it onto
(e.g. screws, washers, lag bolts, nuts, etc.).
Position 1
Position 2
Position 3

7oneida-air.com
Assembly Instructions (Continued)
2 Arrange the Mid Braces (B) in a square so
that each end overlaps over one and under the
other neighboring Mid Brace [FIG. 2a]. Repeat
with all Mid Braces until you have a Square
assembled [FIG. 2b].
Secure the Mid Braces together using four
Carriage Bolts (F1), four Washers (F2), and
four Nylock-Nuts (F3) [FIG. 2c] .
Note: Finger tighten only at this time.
3 Align the Upper Leg (E) and Lower Leg (A).
read two Carriage Bolts (F1) through both
to hold it in place. [FIG. 3].
Note: Finger tighten only at this time.
FIG. 2a
FIG. 2c
FIG. 2b
FIG. 3

8
Oneida Air Systems
Assembly Instructions (Continued)
4 Lay the Mid Brace assembly (B) over the
Aligned Leg assembly (A, E) threading the
Carriage Bolts (F1) through all components.
[FIG. 4a]
Secure both assemblies using four Carriage
Bolts (F1) , four Washers (F2), and four
Nylock-Nuts (F3) [FIG. 4b].
Attach the three remaining Leg assemblies to
the Mid Brace assembly and secure.
Note: Finger tighten only at this time.
5 If you did not purchase the 18" Stand proceed
to Step 6.
Attach two of the Top Braces (D) onto
opposite sides of the Stand with four Carriage
Bolts (F1), four Washers (F2), and four
Nylock-Nuts (F3) each. en attach the
remaining two Top Braces as shown in [FIG.
5]. Secure each using four Carriage Bolts (F1),
four Washers (F2), and four Nylock-Nuts (F3).
Note: Finger tighten only at this time.
FIG. 4a
FIG. 4b
FIG. 5

9oneida-air.com
Assembly Instructions (Continued)
FIG. 6
6 If you did not purchase the Leg Extensions,
proceed to Step 9.
e Leg Extensions must be positioned at
the correct clearance height for your waste
containment and lter setup [FIG. 6].
. Position 1: For 35 gallon drum with
Universal Drum Dolly.
. Position 2: For 55 gallon drum and/or
Stacking Sound Filter.
. Position 3: For 55 gallon drum, Universal
Drum Dolly, and/or Stacking Sound Filter.
Note: Finger tighten only at this time. We
recommend that the leg extensions be assembled
laying down and then raised into position later
on.
7 Using the previously selected positioning
holes, align the Lower Leg (A) and the Leg
Extension (G) as well as the Mid Brace (B) in
the lower hole. read two Carriage Bolts (F1)
to hold it in place [FIG. 7a]. Secure with two
Washers (F2), and two Nylock-Nuts (F3) [FIG.
7b].
Note: Finger tighten only at this time. We
recommend that the leg extensions be assembled
laying down and then raised into position later
on.
FIG. 7b
FIG. 7a
A
G
B
Position 1
Position 2
Position 3

10
Oneida Air Systems
FIG. 8
FIG. 9
Assembly Instructions (Continued)
8 From the previous step, nishing securing
the Leg Extension assembly (A, G, B) with an
additional Mid Brace (B) using two Carriage
Bolts (F1), two Washers (F2), and two Nylock-
Nuts (F3) [FIG. 8].
Repeat Steps 7 and 8 until all Leg Extension
assemblies are secured to the Stand.
Note: Finger tighten only at this time. ere are
only three Mid-Braces to allow an opening for
the dust container.
9 Raise the Stand up and ensure that all
components are squared and level before
tightening the hardware [FIG. 9].
We recommend torquing all of the bolts down
to 250 in.-lbs. (~20 .-lbs.).
A
G
B

11oneida-air.com
10 ere are two options for mounting the feet to
your stand. Choose either or both options that
best meet your needs:
a. To prevent slipping and scung, slip a
Plastic Stand Foot (F4) to the bottom of
each Leg Assembly [FIG. 10a].
b. For additional stability and/or if you plan
to bolt the stand to the oor, attach a
Stand Foot (C) to the bottom of each Leg
Assembly. Secure the Stand Foot in place
using Carriage Bolts (F2), Washers (F2),
and Nylock-Nuts (F3) [FIG. 10b].
Note: We recommend that all feet be installed so
that they are facing forward or backwards [FIG.
10c] from the center of the system to ensure
proper stability during operation.
11 If desired, the Stand can be bolted down to the
oor through the holes on the Stand Feet (C)
[FIG. 11].
Note: You will need to supply your own
hardware (e.g. screws, washers, lag bolts, etc.)
for securing the system to the oor.
FIG. 10b
FIG. 10c
FIG. 11
FIG. 10a
Assembly Instructions (Continued)

Customer Service Dept.
1-866-387-8822 • [e-mail]
1001 West Fayette Street, Syracuse, NY 13204 U.S.A.
Copyright © 2022 Oneida Air Systems, Inc.
ank you for your business!
Regardless of where you purchased your system, if you have
any questions or issues with missing / damaged parts, please
call Oneida Air Systems rst to let us help resolve your
problem. We fully stand behind the quality of our product
and place the utmost value on our customer’s satisfaction.
We want to do everything possible to make your purchase
and experience with Oneida Air Systems a good one!