INUX3D PK1 PRO Streamer AN User manual

© INUX3D 2022 V1.2
Assembly Instructions
Biodegradable according
to DIN EN ISO 14855
MADE IN EU
8 586022 660566
TUV
TUV Hessen
EN ISO
9001
2015
ADDITIVE MANUFACTURING
®
BLK
PRO
Streamer YP
Cage for YoloBox Pro
BLK
PRO
Streamer YP
Cage for YoloBox Pro
ADDITIVE MANUFACTURING
®
8 586022 660566
Streamer AM
Stand for the ATEM Mini / Pro / ISO
Lower Strut Assembly
All of the fasteners required for assembling this component are found in Bag 2.
Bag 2 contains 4 x M4*8mm bolts, 4 x M4 Hex Nuts and 4 x M2.5*6mm bolts
ŸFlip the entire assembly on it's back so that the undersides are visible.
ŸThe lower strut assembly comprises of 4 parts, 2 Left and 2 Right. Each part is
marked L or R
ŸUsing the M2.5x6mm bolts you will now join both the Left and Right lower
struts together to form a longer strut. The M2.5 bolt will pass through the bolt
hole on the Left part and you will screw directly into the plastic of the Right
part.
ŸYou will perform this step twice, creating 2 lower struts.
M2.5x6
M2.5x6
M4x8
M4x8
M4x8
M4x8 Rubber Foot
Rubber Foot
Rubber Foot
Rubber Foot
Front Right Strut
Front Left Strut
ŸWe will tighten the Top Left and Right bolts as well as the lower strut bolts to
stiffen up the entire assembly.
ŸPosition one of the lower strut assemblies into the notches under each of the
Left and Right sides.
ŸInsert an M4*8mm bolt from below and place an M4 hex nut into the nut
shaped recesses and loosely tighten the protruding bolt.
ŸRepeat for the second lower strut assembly.
ŸAttach the 4 rubber feet in the positions indicated in the diagram above.
DO NOT OVER TIGHTEN.
Biodegradable according
to DIN EN ISO 14855
MADE IN EU
8 586022 660252
Compatible with the ATEM Mini Extreme
and ATEM Mini Extreme ISO
INUX3D
d e s i g n s t u d i o
TM
TUV
TUV Hessen
EN ISO
9001
2015
5
INUX Cloud s.r.o.
Galvaniho 12B
Bratislava 82104
Slovakia
Assembly Instructions
This product was produced with an additive manufacturing process. Minor surface imperfections do not affect the overall product functionality. Instagram: @aaronpk_tv | Twitter: @aaronpk
You can also get support and show off photos of your rigs in our friendly community at
forum.livevideotech.today
Thanks so much for your support! I hope this stand makes your productions even more
successful. I'd love to see a photo of your new rig! Post a photo on Instagram or Twitter and
tag it with #pk1stand
- Aaron
Parts of this product were produced with an additive manufacturing process. Minor surface imperfections do not affect the overall product functionality.
Biodegradable according
to DIN EN ISO 14855
MADE IN EU
8 586022 660566
TUV
TUV Hessen
EN ISO
9001
2015
ADDITIVE MANUFACTURING
®
BLK
PRO
Streamer YP
Cage for YoloBox Pro
BLK
PRO
Streamer YP
Cage for YoloBox Pro
ADDITIVE MANUFACTURING
®
8 586022 660566

© INUX3D 2022 V1.2
PK1 PRO STREAMER AM
Assembly Instructions Page 2 of 5
Begin by placing the left side
of the Mini Stand smooth side
down with the cold shoe facing
you
You are looking at the left rear
of the Mini Stand
Place your ATEM Mini into the
side of the stand so that the
screen is facing away from you
Insert the 2 aluminium bars into
the corresponding spaces in the
side of the Mini Stand
B
B
A
A
Important:
Slide 2x M4 slide in T-Nuts for
the 2 cold shoes here - B
If you are using the OPTIONAL
Cheesebar, slide 2x M5 sliding
T-Nuts for the CheeseBar tripod
mount here - A
Example
of A & B
* Please note that your kit comes with extra M4 and M5 nuts and
bolts so you can attach other accessories you may already have

© INUX3D 2022 V1.2
Place the right side of the Mini
Stand over the top of the ATEM
Mini and the 2 aluminium bars
Drop in two of the supplied
M5x25 mm bolts into the holes
to afx the right side of the Mini
Stand onto the aluminium bars
These only need to be lightly
tightened. You will damage the
plastic sides if you tighten with
force
Place your hand underneath
the entire assembly and
squeeze the Left and Right
sides together
Flip the entire Mini Stand over so
the left side is now on top
Drop in 2 more M5x25 mm
bolts into the holes and lightly
tighten
Position the Mini Stand as
shown and note the 2x M4 slide
in nuts you dropped in earlier
We will be attaching the top
cold shoe mounts to these two
T-nuts
PK1 PRO STREAMER AM
Assembly Instructions Page 3 of 5

© INUX3D 2022 V1.2
Place each cold shoe on top of
the Mini Stand and very loosely
tighten the 2x M4x8 bolts into
the T-nuts
Now that you have both bolts
attached, slide the cold shoes
into their desired position
You may now tighten the bolts
A
This is simply a zoomed in
view of how a cable manager
assembly should look once
attached
PK1 PRO STREAMER AM
Assembly Instructions Page 4 of 5
2
3
1Attaching the cable managers
requires the use of an M4x8mm
bolt through the cable manager
and into an M4 drop in nut.
Note that the nut ts into the
slot of the aluminium bar
1. Place the bolt through the
cable manager hole and very
loosely into the drop in nut
2. Position the drop in nut so that
it ts into the slot of the bar
3. Tighten the bolt so the drop in
nut turns and locks into place
at the position you require

© INUX3D 2022 V1.2
We will now ip the Mini Stand so the bottom is facing upwards and
the wire managers are pointing away from us
If you are attaching the OPTIONAL cheesebar, you will lightly attach
the cheesebar to the slide in T-nuts with 2 M5x8mm bolts. The
majority of the cheesebar will be toward the rear
Once both bolts are attached to the nuts, slide the cheesebar along
the aluminium bar so that it is centred along it’s length
You may now tighten the bolts
If you have attached the
OPTIONAL cheesebar, you can
mount it onto a 1/4-20 or 3/8
tripod or similar mount
The last step is to add the rubber
feet in the event you wish to
move your stand from the tripod
to a desktop position
PK1 PRO STREAMER AM
Assembly Instructions Page 5 of 5
Congratulations on completing
the assembly of your PK1 Pro
STREAMER AM