IOGear GPS702e3W6 User manual

1
GPS702e3W6
PART NO. M0554
Installation
Installation
Installation Guide
eSATA 3Gbps Dual ports Express Card/34 Host

3
Table of Contents
Introduction 4
Features 5
Package Contents 6
Software Installation 7
Federal Communications Commission (FCC) Statement 10
CE Statement 12
Limited Warranty 13
Contact 14

4
Introduction
The ExpressCard Host allows you to upgrade your Notebook computer with up to two SATA II
Channels. The board provides a 2.5Gbps ExpressCard interface on the host side, and dual fully
compliant SATA II 3Gbps ports on the device side to access Serial ATA mobile external and internal
storage devices such as: hard drives, ZIP drives, CD-ROMs, CD-RWs and DVD-ROM drives.

5
Features
External SATA II (eSATA) Connector•
48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB•
Supports 1-lane 2.5Gbps ExpressCard/34•
Hot-plug capability•
Supports SATA II transfer rate of 3.0Gbps•
Fully compliant with Serial ATA 1.0 specifications•
Supports two independent Serial ATA channels•
Independent Link, Transport, and data FIFO•
Independent command fetch, scatter/gather, and command execution•
Supports Legacy Command Queuing (LCQ)•
Supports Native Command Queuing (NCQ)•
Supports Non-zero offsets NCQ•
Supports Out of order data delivery NCQ•
Supports FIS-based switching with Port Multipliers•
31 Commands and Scatter/Gather Tables per Port•
Two LEDs indicate for HDD access•
Completely with drivers for Windows NT, Windows 2000, Windows XP, Windows Vista and Windows•
Server 2003

6
Package Contents
SATA ExpressCard Host Adapter•
Quick Start Guide•
Driver CD•

7
Windows XP Installation
1. Insert the SATA Card into an available slot.
Connect the serial ATA cable(s) between the
SATA port and serial ATA device(s).
2. Windows will display the ‘Found New
Hardware Wizard’. A new ‘Mass Storage
controller’ will become detected.
3. Insert the Driver CD into your CD-ROM/DVD
Drive.
4. Select “Install from a list or specific
location (Advanced)”, and click “Next”.
Software Installation

8
5. Select “Search for the best driver in these
locations”, and check “Include this location
in the search:” Be sure to uncheck the other
available boxes.
6. Type the appreciate media drive letter and
select the “Browse” option.
7. Specify a location [CD Drive Let-
ter]:\SATA Express_2Port \Sil3132 \
WinXP_2000_2003_NT, and click OPEN then
select OK.
8. When the wizard indicates that it found a driver
for the device click ‘Next’.
9. The wizard will now copy the required files to
the system and initialize the Driver. After starting
the driver the wizard will display a completion
dialog, click ‘Finish’ to exit the wizard.

9
Verify Windows XP Installation
1. Right click on the ‘My Computer’ icon, select
‘Properties’, left click on the ‘Hardware’ tab,
and select the ‘Device Manager’ button.
2. Double click on ‘SCSI and RAID Controllers’,
If there is no yellow ‘! ‘ or ‘ ? ‘ in front of
‘Silicon Image SiI 3132 SATALink Controller’,
the driver is functioning properly.

10
Federal Communications Commission (FCC) Statement
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.