IOne Scorpius-P20 User manual

ENGLISH
Scorpius-P20
2.4GHz Wireless Joystick Keyboard
User Guide
Introduction
Thank you for purchasing Scorpius-P20 2.4GHz Wireless Joystick Keyboard.
For an ideal performance, please follow the instructions of this user guide. If you
have any question, please contact us at www.ione.com.tw or www.itron-europe.com
Scorpius-P20 combines mouse and keyboard functions in one device with
advanced technology to work with your media center system. This is a plug and
play device under Win ME/2000/XP.
Features
• Built-in 360 ﾟjoystick and buttons for mouse function
• 2.4GHz RF with 8 channels / 8 ID per channel
• Up 10 meter operation range
• Low power consumption
• Compatible with Microsoft WIN 95/98/ME/2000/XP
• Compatible with Macintosh OS system.
I. Package Content:
1. SC-P20 Wireless Joystick Keyboard
2. Mini USB RF Receiver
3. 2 AA Batteries
4. User Guide
II. System Requirements:
1. IBM or compatible system
2. WIN 98SE/2000/ME/XP

3. Mac OS system
III. Definition of panel information:
Signal Indicator Description
Connect Button Reset button for new ID or bad connection
Transmitter Orange Indication of RF transmitting status
FN Green Activation of “numerical keypad” function button
Battery Low Red Indication of “Battery Low” status
LED on RF receiver Orange
Red
Indication of RF receiving status.
Indication of “Battery Low” status.
IV. Hardware Setup Notice:
1. When you connect the receiver with your computer, please do not touch the
joystick until the new device installation process is finish.
2. Battery Installation---When you install batteries on the back of the keyboard,
please do not touch the joystick.
3. If you are using Win 98 OS, the system may require original Win 98 system CD to
complete the installation. Please follow the steps to search the driver of USB
device and complete the setup.
V. Connect ID Setting:
This product’s connection ID has been set and paired with the receiver during the
assembling. If there is interference or the loss of connection, please reset the
connection again. Please follow the procedure below for new ID setting.
Step 1: Plug the RF receiver into the USB port of your computer.
Step 2: Press the connect button on the RF Receiver. The LED on the RF

receiver will start to blink.
Step 3: Within 8 seconds, please press the “connect” on the keyboard.
Step 4: The LED on the RF receiver will blink faster if the ID setting is
completed.
Step 5: If the keyboard does not work properly, please go back to step 2 and
repeat step 2 to Step 4.
TROUBLE SHOOTING GUIDE
Symptom Remedy
Keyboard or cursor
doesn’t function at all
• Please press the connect button on the receiver
• Within 8 second, please press the connect button on the
keyboard
• The LED on the receiver will blink if the connection
setting is completed
The cursor on the
screen moves
automatically without
operating.
• Reinstall batteries, and do not touch the joystick during
the installation.
• If the device doesn’t function, please follow the connect
ID setting
Orange LED on RF
receiver is not lit
• Ensure computer is powered on and receiver is
connected to the USB port of computer.
• Unplug the receiver and plug it in again.
Keyboard or cursor
doesn’t function
properly
• When you press a key and the ‘transmitter’ LED on the
keyboard does not blink, it could be out of battery and
please replace the battery of keyboard.
• If the LED on RF receiver dose not blink when you
operate the keyboard or joystick, please reposition the
keyboard and ensure the distance between keyboard and
RF receiver is within 7 meters or less
• If the problem persists, please reset the connect ID.
Please go to connect ID setting procedure.
For further Question Please e-mail us at www.ione.com.tw or
www.itron-europe.com.

NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiated radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter