iPort CM-IW200 User manual

Control Mount
Instruction Manual
CM-IW200

CM-IW200 Instruction Manual
2
Introduction
The iPort®Control Mount is an in-wall system that
allows an iPod touch®(4th generation only as of
publication date. Please visit www.iportmusic.com
for updated/additional iPod product releases) to
become a semi-permanent fixture in your home
control system through wireless applications.
Before installing and using the CM-IW200, please
read and follow all of the instructions in this manual
carefully.
System Capabilities:
• Deliverslocal-zoneunbalancedaudioupto30
feet (9m) from the mount.
• ChargestheiPodtouchwhileitismounted.
• Featuresvariableaudiovolumecontrolviathe
installed iPod touch in portrait orientation.
• Fixedaudiovolumecontrolviaconnectedaudiosystemsuchasareceiver.
• Providesadditionallongdistancepoweronlyupto200’using18awgwire.Seechart
belowforadditionalwirespecs.Note:Audiodistanceisstilllimitedto30feetfrom
themountandwallplate.Foradditionalpower-onlydistance,usethe2pinconnec-
torlocatedonthebackoftheaudiowallplate.(SeeFigure3)
iPort Control Mount Box Contents:
 (1)iPortin-wallmountingsystem(faceplateandmountingcradle)
 (1)Audiowallplate
 (1)Regulatedpowersupply
 (1)Installationcut-outtemplate
 (1)Instructionmanual
Required Tools
The following tools are required to install the iPort:
•#2Phillipsscrewdriver
•Wirecuttersandwirestrippers
•RJ-45cablecrimptoolandmodularconnectors
•Sheetrocksaw(forretrottingintoanexistingwall)
Wire Gauge Distance (Feet)
22awg 75
20awg 120
18awg 200

CM-IW200 Instruction Manual
3
Selecting an Installation Location
The iPort Control Mount is designed for use in normal interior environments. When
selecting an installation location for the Control Mount, please consider the following:
• DonotusetheControlMountoutsideorinahumidorwetenvironment.Itisnot
waterproof or water-resistant.
• TheControl Mountcut-out musthave enoughdepth withinthe wallcavity forthe
Control Mount and its connections.
• The Control Mount has screw mounting holes on both sides that allow it to be
installed up against a stud.
• CheckforastrongWi-FisignalatthemountinglocationusingtheiPodtouchthatis
to be installed in the Control Mount.
Control Mount Rear Connections
AudioConnector:RJ-45jackconnectstotheaudiowallplateviaCat5cable.Theaudio
connectiontransmitsunbalancedaudiototheaudiowallplate.ItalsoreceivesDCpower
from the audio wall plate.
Wiring Cat5/RJ-45 Cable
TheCat5cableandRJ-45connectorusediniPortinstallationsmustbewiredaccording
totheT568A(“Straight-Through”)Standardwithcableswiredidenticallyatbothends.
TopreparetheCat5cableandRJ-45connectorforiPortinstallation:
1. PulltheCat5wirethroughthewallbetween
the desired locations.
2. Useastripperorknifetostripabout1”ofthe
cablejacketoffeachendofthewire.
•Becareful nottonickanyoftheindividual
wires.
3. Untwistthewirepairsandspreadthemat.
ArrangethemasshowninFigure2.
4. Trimtheendsoftheindividualwiresto½”in
length, making sure that they are even with
each other. Flatten the wires against each
other, leaving no space between them.
5. HoldtheRJ-45connectorclip-sidedownand
inserttheCat5wireendsrmlyintotheconnector.Makesurethatallthewiresareatalltheway
to the very front of the connector.
6. Re-conrmthatthecolororientationmatchesthediagramandthatcablejackettsagainstthe
connector stop.
7. FirmlycrimptheRJ-45connectorwiththecrimptool.Conrmthattheconnectoriscrimpedrmly
andthatallthewiresareatrightupagainstthefrontoftheconnector.Ifevenoneofthesewires
isincorrect,cuttheconnectoroffthecableandrepeatsteps2–7withanewRJ-45connector.
Figure2:RJ-45AudioConnector

CM-IW200 Instruction Manual
4
Installation Preparation
The CM-IW200 features an integral Roto-Lock mounting system for quick mounting
directly into existing walls. Once the hole is cut and the cables have been run, you can
install the iPort into the wall in a matter of seconds.
1. DeterminethelocationfortheiPortControlMountandthewallplate.Notethatthe
unbalancedaudioisdesignedforuseinalocal-zonesystemwheretheiPortwallplate
andaudioequipmentarelocatedlessthan30feetfromtheControlMount.
2. Perform an obstruction survey to ensure there are no studs, conduit, pipes, heating
ducts, or air returns that will interfere with the Control Mount.
Note: You can mount the CM-IW200 directly next to a wall stud on either side (see
Step 8).
3. Findthecut-outtemplateprovidedintheCM-IW200packaging.Positionthetemplate
where the Control Mount is to be located and pencil an outline on the wall.
Note: Be sure to confirm the installation of the iPort at this time for either vertical (por-
trait) or horizontal (landscape) orientation. Certain applications of the mounted iPod
touch work only in one orientation, so be sure to confirm the client’s requirements
before cutting the hole. Note: Variable audio only available in portrait orientation.
•Ifyouareunsureaboutobstructions,drillasmallholeinthecenteroftheoutlineand
insert a coat hanger wire into the hole to feel around for possible obstructions.
4. Cut the opening using a drywall saw.
iPort Connections and Installation
See Figure 3
1. Decidewhichinstallationmethodisprefered.Beforemakingconnections,runalength
ofCat5cablethroughthewallfromtheControlMountlocation to the audio wall plate
location,asshowninFigure3.Thewallplatecanbelocatedupto30feetfromthedock.
•FindalocationforthewallplatethatisnearbothasourceofACpowerandthelocal-
zoneaudiosystem.
2. InstallRJ-45connectorsonbothendsoftheCat5cableasexplainedinFigure2:Cat5/
RJ-45Audioconnector.TheaudioCat5/RJ-45cablepinassignmentis:
3. PlugtheCat5cableintotheaudioconnectorontheControlMountandtheRJ-45jack
onthewallplate,asshowninFigure3.
4. Install the wall plate into an electrical box in the room near the audio system.
Pin1: Unused
Pin 2: Unused
Pin3: AudioLeft
Pin 4: Unused
Pin5: AudioRight
Pin6: Unused
Pin 7: Ground
Pin8: +15V

CM-IW200 Instruction Manual
5
Figure3:iPortSystemConnectionOptions
+
-
+
-
up to 200ft
with 18 gauge wire
up to 200ft
with 18 gauge wire
For local audio and
local power
For local audio and
extended power
For extended
power only
For extended
power only
up to 200ft
with 18 gauge wire
+
-
+
-
21 3 4
POWER INTERNETWIRELESS
ETHERNET PORT
CM-IW200
®
U.S. Patent No. 7,493,142
Additional Patents Pending
Designed and Engineeredin the USA
33-5522 1-11
LABEL SIZE: 2” x 0.5”

CM-IW200 Instruction Manual
6
IMPORTANT: Do not install the iPort’s wall plate
in the same electrical box as AC house wiring,
a light switch, or any other high-voltage device
or control. The wall plate can share gang boxes
with other iPort Control Mount wall plates or
with controls such as A/B speaker switches,
infrared receivers, and volume controls, if
these other devices are rated as Class 2 devices
according to the National Electrical Code.
5. UseastereoRCAaudiocabletoconnect
the wall plate’s audio connectors to a
source input on the local-zone audio
system,asshowninFigure3.
6. Prior to placing the mounting cradle into
thewall,pullasufcientlengthoftheCat5
cable and its attached RJ-45 connector
through the opening in the top of the
mounting cradle, as shown in figure 4.
7. The retainer and cradle are pre-assembled
with internal packaging materials.
Disassemblebyremovingthefourscrews.
Discardthefoamblockandcardinsert.
8. Insert the Control Mount mounting cradle
into the opening in the wall.
Note: The Roto-Lock system can accom-
modate wall thickness of 3/8” to 3/4”
and can be extended to 1 1/4” with the
removal of the toggle caps.
9. Hand-tightenthefourRoto-Lockscrewson
the Control Mount’s utility box as shown
in Figure 5. The Roto-Lock clamps will
automatically rotate into position behind
the wall and begin clamping the mount.
•Whenyounoticeresistanceonthefour
screws, the Control Mount has been
clamped successfully.
CM-IW200
®
U.S. Patent No. 7,493,142
Additional Patents Pending
Designed and Engineered in the USA
33-5522 1-11
LABEL SIZE: 2” x 0.5”
Figure5:Roto-LockScrewLocations
Figure4:MountingCradleInstallation

CM-IW200 Instruction Manual
7
IMPORTANT: NEVER over-tighten
the Roto-Lock screws.
10.Ifthereisawallstudupagainstoneside
oftheutilityboxthatpreventsoneRoto-
Lock clamp from operating, secure the
box by hand-driving a 1½” #6 drywall
screw (not provided) through the hole on
that side of the chassis and into the wall
stud.
IMPORTANT: Do not over-tighten the
drywall screw.
11.PlaceiPodtouchintoFascia.Allighpower
button on iPod with Power Button on
Fascia.SeeFigure6
12. Place back plate over iPod and secure
with 4 screws. The back plate has a foam
pad to hold the iPod touch very securly.
SeeFigure7
13.Place the conector board into the iPod
touch and secure to backplate with 2
screws. See Figure 8. Connect RJ-45
Cable to connector
Figure6:InsertiPodintoFascia
Figure7:AttachBackPlate
Figure8:AttachConnectorBoard
Figure5:Roto-LockScrewLocations

CM-IW200 Instruction Manual
8
14.Attach the faceplate to the utility box as
showninFigure9.
15. Plugtheincluded DCpower supplyinto
the Power connector on the wall plate
andintoawalloutlet,asshowninFigure
3.
Note: To sync your iPod touch with your
computer, please follow the steps above
in reverse order to remove the iPod touch
and sync. Once your synchronization is
complete, reinstall the iPod touch and
follow the steps to reassemble.
Figure9:AttachingAssembly

CM-IW200 Instruction Manual
9
Operation
Once installed, the iPod touch is now fully
functional.
Use the iPod touch screen to choose: the
home screen, applications, music, email.
A power on/off button is located on the
edge of the iPort Control Mount as noted
ingure10.
Note: For questions regarding the touch-
screen functions of your iPod touch, please
visit: www.apple.com
Figure10:Faceplate
POWER BUTTON

CM-IW200 Instruction Manual
10
4.027in
102.29mm
5.969in
151.61mm
2.400in
60.96mm
2.190in
55.62mm
Specifications
Powersupply: 15VDC,regulated
Dimensions(WxHxD): 4.027”x5.969”x2.4”(102.29mmx151.61mmx60.9mm)
Cut-outDimensions(WxH): 3.42”x5.34”(86.87mmx135.64mm)

CM-IW200 Instruction Manual
11
LIMITEDONE(1)YEARWARRANTY
iPortwarrantstotherstend-userpurchaserthatthisiPort-brandproduct(“Product”),whenpurchasedfromand
installed by an authorized iPort Dealer/Distributor, will be free from defective workmanship and materials in the
initial installation for the period stated below. iPort will at its option and expense during the warranty period, either
repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent at no
charge for parts, labor and return shipping.
EXCLUSIONS
TOTHEEXTENTPERMITTEDBYLAW,THEWARRANTYSETFORTHABOVEISINLIEUOF,ANDEXCLUSIVEOF,
ALLOTHERWARRANTIES,EXPRESSORIMPLIED,ANDISTHESOLEANDEXCLUSIVEWARRANTYPROVIDED
BY IPORT.  ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY,IMPLIEDWARRANTYOFFITNESSFORUSE,ANDIMPLIEDWARRANTYOFFITNESSFORA
PARTICULARPURPOSEARESPECIFICALLYEXCLUDED.Nooneisauthorizedtomakeormodifyanywarranties
on behalf of iPort.
ThewarrantystatedaboveisthesoleandexclusiveremedyandiPort’sperformanceshallconstitutefullandnal
satisfactionofallobligations,liabilitiesandclaimswithrespecttotheProduct.INANYEVENT,IPORTSHALLNOT
BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY, BODILY INJURY, OR PERSONAL
INJURYDAMAGESARISINGFROMTHEPRODUCT,ANYBREACHOFTHISWARRANTYOROTHERWISE.
This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state.
Some states do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions
and limitations may not apply. If your state does not allow disclaimer of implied warranties, the duration of such
impliedwarrantiesislimitedtotheperiodofiPort’sexpresswarranty.
______________________________________________________________________________
YourProductModelandDescription:iPortControlMountCM-IW200
Warranty Period for this Product:  One (1) year from the date on the original sales receipt, invoice or other
satisfactory proof of purchase.
Additional limitations and Exclusions From Warranty Coverage:  The warranty described above is non-
transferrable, and does not include damage to allied or associated equipment which may result for any reason
from use with this Product, and does not include Product failure caused by accident, disaster, negligence,
improper installation, misuse (e.g. overdriving the amplifier or speaker, excessive heat or cold or humidity,
outdoorinstallation),orfromserviceorrepairwhichhasnotbeenauthorizedbyiPort.
Obtaining Authorized Service: If you purchased your iPort from an iPort Dealer, you (1) must contact your
authorizediPort Dealer/InstallerorcalliPortCustomerServiceat(800)582-0772withinthewarrantyperiod,(2)
mustobtainareturnmerchandise number(RMA),and (3)delivertheProductto iPortshippingprepaidduring
the warranty period, together with the original sales receipt, invoice or other satisfactory proof of purchase from
youriPortDealer.IfyoudidnotpurchasefromaniPortdealer,youmustcontactyourauthorizedsellerwithinthe
warrantyperiodandobtaininstructionsforobtainingauthorizedservice.

sanclementeca|888.45. iPort | www.iportmusic.com
33-54433-2011
©2011 Dana Innovations. All rights reserved.
iPort and Roto-Lock are registered trademarks of Dana Innovations. iPod is a trademark of Apple Inc.
“Made for iPod” means that an electronic accessory has been designed to connect specically to iPod and
has been certied by the developer to meet Apple performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and regulatory standards. Please note that the use of
this accessory with iPod may affect wireless performance.
Due to continuous product improvement, all specications are subject to change without notice.
For the latest iPort product information go to www.iportmusic.com