Ismart AMC-F2002W User manual



IP HD PTZ Color Video
Camera
User Manual V1.0






SAFETY NOTICE-IMPORTANT!!!
The following important notes must be followed carefully to run the camera and respective
accessories in total safety. The camera and relative accessories are called video system in
this section.
Before installing the camera, please read this manual carefully. Please follow installation
instructions indicated in this manual during installation. Please keep this manual for future
use.
The installation should be performed by qualified service personnel or system installers in
accordance with all local rules.
Before powering on the camera, please check the power voltage carefully. Make sure that
you are using the correct power source.
Please put the power cable, video cable and control cable in safe place.
Do not operate the camera beyond the specified temperature and humidity. Working
temperature range of the camera is between -20℃and +60℃. The ambient humidity range
is less than 95﹪.
During transporting, avoid violent shake or force to the camera.
To prevent electric shock, do not remove screws or housing of the camera. There are no
self-serviceable parts inside. Refer to qualified service personnel for servicing.
Video cable and RS485 cable should be kept far away from other cables. Shielded and
independent wiring is necessary for video and control cables.
Never aim the lens of the camera at the sun or other extremely bright objects. Otherwise, it
may cause damage.
When cleaning the camera, please use soft cloth. If the camera is very dirty, wipe it off
gently with a soft cloth moistened with a weak solution of water and a neutral kitchen
detergent. Wring all liquid from the cloth before wiping the camera, then wipe off all
remaining dirt with a soft, dry cloth. Use lens cleaning paper to clean the lens.



Do not move the camera head manually. In doing so would result in malfunction of the
camera. Do not hold the camera head when carrying the video camera.
This camera is for indoor use only. It is not designed for outdoor use.
Make sure the camera is not directly exposed to rain and water.
Make sure the camera is far away from area where radiation, X-rays, strong electric
waves, or magnetism is generated.



CONTENTS
ABOUT THE PRODUCTS ------------------------------------------------------ 1
FEATURES -------------------------------------------------------------------------------- 1
LIST OF PARTS &ACCESSORIES ------------------------------------------------------------ 1
MAIN PARTS &INTERFACES ---------------------------------------------------------------- 2
INSTALLATION ----------------------------------------------------------------- 3
INSTRUCTIONS ---------------------------------------------------------------------------- 3
CONNECTIONS ----------------------------------------------------------------- 4
MENU SETTINGS --------------------------------------------------------------- 5
MENU CONFIGURATION --------------------------------------------------------------------- 5
MENU EXPLANATION ----------------------------------------------------------------------- 8
VIDEO MENU ------------------------------------------------------------------------------ 9
EXPOSURE MENU -------------------------------------------------------------------------- 9
COLOR MENU ----------------------------------------------------------------------------- 10
PAN/TILT/ZOOM --------------------------------------------------------------------------- 10
SYSTEM MENU ---------------------------------------------------------------------------- 11
STATUS MENU ---------------------------------------------------------------------------- 11
RESTORE DEFAULTS ---------------------------------------------------------------------- 12
LIST OF SPECIAL PRESET COMMANDS ------------------------------------------------------ 12
NETWORK SETTING ----------------------------------------------------------------------- 13
QUICK GUIDE ----------------------------------------------------------------------------- 13
IPCAMCONF ------------------------------------------------------------------------------ 14
LOCAL MONITORING AND SETUP ----------------------------------------------------------- 16
ANNEX 1 TECHNICAL SPECIFICATIONS ------------------------------------- 28
ANNEX 2 SIZE AND DIMENSION ---------------------------------------------- 30
TROUBLESHOOTING --------------------------------------------------------- 31











1
About The Products
The products is a full HD mobile waterproof
cameras, optional wifi (built-in 5G wifi and
lithium battery module) and network models.
Used for fixed & mobile football recording and
capturing. Support distant control, video
switch among different scenes.
Features
1/ 2.8 inch CMOS sensor, 2.14
megapixel;
20x optical zoom;
H.265/ H.264, support 1080P60, low delay
in network transmission;
Dual stream;
1 channel audio input, AAC encode;
Built-in battery module, with max. 8 hours
of battery and supporting quick charge
(only for wifi model);
Built-in 5G wifi module, (only for wifi
mode);
Support audio and video transmission via
cables;
Support battery power supply (only for wifi
mode), support adapter power supply;
IP66;
Support HTTP/ RTSP/ RTMP/
ONVIF and etc. ;
Support TF card for local storage;
Provide open SDK for user-defined
features.
List Of Parts & Accessories
Whenyouopenthebox,checkallaccessories
accordingtothepackinglist.
Camera (1)
Power Adapter (1)
Aviation plug able(Only for wifi model)


Disk X1



2
Main Parts & Interfaces
Camera
Front View
1 Camera module
2 waterproof switch
Rear View
Wifi model



3 aviation plug
Network model





3 cables
BottomView

4 install hole
1/4”inch thread，used for fix mounting。


3
INSTALLATION
INSTRUCTIONS
Tripod installation
Tripod Installation

1. User should prepare a tripod with a ¼ inch
threaded connection column by self, then
the ¼ inch threaded hole at the bottom
should aligned to the clockwise direction
of the connecting column on the tripod,
make sure the fixed mount before release
your hands.


Note
Before installing, make sure there is
enough space to install the camera and
its parts.
Make sure the installed place is strong
and safe enough to hold the camera
and relative parts, it is suggested that
the installed place can withstand 4
times the weight of the camera and its
relative parts.


4
CONNECTIONS
Please check the correct connection before using.
Wifi model

Network model



5

MENU SETTINGS
Menu configuration
<VIDEO> SHARPNESS 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15
BRIGHTNESS 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
Please refer
to P9
CONTRAST 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
GAMMA MODE
0, 1, 2, 3, 4,
2DNR LEVEL
1，2，3，4，5，OFF
3DNR LEVEL
1，2，3，4，5，OFF
WIDE DYNAMIC
1，2，3，4，5，OFF












6
<EXPOSURE>
Please refer to
P9
MODE FULL AUTO
MANUAL GAIN 0, +2, +4, +6, +8, +10,
+12, +14, +16, +18, +20,
+22, +24, +26, +28，+30
SPEED 1/1, 1/2, 1/3, 1/6, 1/12, 1/25,
1/50, 1/75, 1/100, 1/120,
1/150, 1/215, 1/300, 1/425,
1/600, 1/1000,1/1250,
1/1750, 1/2500, 1/3500，
1/6000, 1/10000
IRIS F14, F11, F9.6, F8, F6.8,
F5.6, F4.8, F4, F3.4, F2.8,
F2.4, F2, F1.6, CLOSE
SHUTTER PRI SPEED 1/1, 1/2, 1/3, 1/6, 1/12, 1/25,
1/50, 1/75, 1/100, 1/120,
1/150, 1/215, 1/300, 1/425,
1/600, 1/1000,1/1250,
1/1750, 1/2500, 1/3500，
1/6000, 1/10000
IRIS PRI IRIS F14, F11, F9.6, F8, F6.8,
F5.6, F4.8, F4, F3.4, F2.8,
F2.4, F2, F1.6, CLOSE
BRIGHT PRI BRIGHT 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,
11, 12, 13, 14, 15, 16, 17,
18,19, 20, 21, 22, 23, 24, 25,
26, 27
EX-COMP ON
OFF
LEVEL 7, -6, -5, -4, -3, -2, -1, 0, +1,
+2, +3, +4, +5, +6, +7
BLC ON
OFF
ANTI –FLICKER OFF,50HZ,60HZ


7

< COLOR >
Please refer to
P10
WB MODE
AUTO，ATW，ONE PUSH，INDOOR，OUTDOOR，
MANUAL ，SODIUM LAMP，FLUO LAMP
SATURATION
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
HUE
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
<PAN TILT ZOOM>
Please refer to P10
PAN/TILT SPEED 1, 2, 3, 4, 5, 6, 7, 8
PTZ TRIG AF ON, OFF
RATIO SPEED ON，OFF
POWER UP ACTION PRESET 1, PRESET 2,
PRESET 3, PRESET 4,
PRESET 5, PRESET 6,
PRESET 7, PRESET 8,
PRESET 9, HOME

< SYSTEM >
Please refer to
P11
ADDRESS 1, 2, 3, 4, 5, 6, 7
PROTOCOL VISCA，PELCO-P，PELCO-D
BAUD RATE 2400，4800，9600，38400
VIDEO FORMAT 1080P60，1080P50，1080I60,
1080I50，1080P30， 1080P25，
720P60，720P50，
MOUNT MODE STAND，CEILING
LANGUAGE ENGLISH,CHINESE
<STATUS>
Please refer to
P11
ADDRESS 1
PROTOCOL VISCA
BAUD RATE 9600
VIDEO FORMAT 1080P25
MOUNT MODE STAND
FIRMWARE VER 1.0.19
<RESTORE DEFAULTS>
Please refer to P12


8
❶
❷
❸
Menu Explanation
Main MenuCall Preset #95 to enter
menu.

❶ MenuTitle
It displays currently selected menu option
❷ MenuOptions
It displays options under current menu title.
Click UP or DOWN button to select among
menu options, once color of options turned to
different color, it indicates the menu has been
elected, click IRIS+ button to get into this
menu.







Submenus
From main menu, navigate to select
<EXPOSURE> menu, click IRIS+ to enter.
<EXPOSURE>Set menu.

❶❷ Please refer to the same controls
to the Main Menu
❸ Menu options
Click or to change the values.


<EXPOSURE>
MODEMANUAL
GAIN0
SPEED1/6000
IRISF14
[ ]SELECT[]BACK
<MENU>
VIDEO
EXPOSURE
COLOR
PANTILTZOOM
SYSTEM
STATUS
RESTOREDEFAULTS

[ ]SELECT[OK]NEXT[]EXIT
❶ ❸
❷
❹


9
VIDEO MENU
VIDEO menu is used to change video value.

SHARPNESS: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11,
12, 13, 14, 15.
BRIGHTNESS: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,
11, 12, 13, 14.
CONTRAST：0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11,
12, 13, 14.
GAMMA MODE：0, 1, 2, 3, 4.
2DNR LEVEL: 1, 2, 3, 4, 5, OFF.
3DNR LEVEL: 1, 2, 3, 4, 5, OFF.
WIDE DYNAMIC: 1, 2, 3, 4, 5, OFF.
EXPOSURE MENU
EXPOSURE menu is used to adjust exposure
value.

MODE
FULL AUTO: Gain, Shutter Speed and Iris
value are adjusted automatically accordingly
to working environment.
MANUAL : manually adjust Gain, Shutter
Speed and Iris.
GAIN: 0, +2, +4, +6, +8, +10, +12, +14, +16,
+18, +20, +22, +24, +26, +28，+30.
SPEED: 1/1, 1/2, 1/3, 1/6, 1/12, 1/25, 1/50,
1/75, 1/100, 1/120, 1/150, 1/215, 1/300,
1/425, 1/600, 1/1000,1/1250, 1/1750,
1/2500, 1/3500，1/6000, 1/10000.
IRIS: F14, F11, F9.6, F8, F6.8, F5.6, F4.8,
F4, F3.4, F2.8, F2.4, F2, F1.6, CLOSE.
SHUTTER PRI: Gain and Iris value are
adjusted automatically according to working
environment; shutter speed value is
adjustable manually.
SPEED: 1/1, 1/2, 1/3, 1/6, 1/12, 1/25, 1/50,
1/75, 1/100, 1/120, 1/150, 1/215, 1/300,
<EXPOSURE>
MODEMANUAL
GAIN0
SPEED1/6000
IRISF14
[]SELECT[]BACK
<VIDEO>
SHARPNESS8
BRIGHTNESS7
CONTRAST2
GAMMAMODE0
2DNRLEVEL2DOFF
3DNRLEVEL3DOFF
WIDEDYNAMIC OFF

[]SELECT[]BACK


10
1/425, 1/600, 1/1000,1/1250, 1/1750,
1/2500, 1/3500，1/6000, 1/10000.
IRIS PRI: Gain and shutter speed value are
adjusted automatically according to working
environment; Iris value is adjustable manually.
IRIS: F14, F11, F9.6, F8, F6.8, F5.6, F4.8,
F4, F3.4, F2.8, F2.4, F2, F1.6, CLOSE.
BRIGHT PRI : Manually adjust the video
brightness.
BRIGHT: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12,
13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24,
25, 26, 27.
EXP-COMP Once EXP-COMP is set as On,
below level options become available-7, -6, -5,
-4, -3, -2, -1, 0, +1, +2, +3, +4, +5, +6, +7.
+7 is the maximum compensation value for
bright, -7 is the maximum compensation value
for dark.
BLC ON, OFF.
Backlight compensation (BLC) is video gain
done automatically to correct the exposure of
subjects that are in front of a bright light
source.
ANTI-FLICKER (OFF, 50Hz, 60Hz): To avoid
video flicker at power systems of different
frequency.
COLOR MENU
COLOR is used to set the color values.

WB MODE : AUTO, ATW, ONE PUSH,
INDOOR, OUTDOOR, MANUAL, SODIUM
LAMP ,FLUO LAMP.
“ONE PUSH”mode，press or ，
select“ONE PUSH TRIGGER” aim the
camera at a pure white object (say a
white paper), then press OK button.
“AUTO”mode, R.GAIN、G.GAIN , B. GAIN
value can be chosen from-7~+7.
“MANUAL” mode: R.GAIN and B. GAIN
value can be chosen from 0~255.
SATURATION : 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,
11, 12, 13, 14.
HUE: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13,
14.
PAN/TILT/ZOOM
PAN/TILT/ZOOM is used to change
pan/tilt/zoom value, available options:
<COLOR >
WBMODEMANUAL
R.GAIN7
B.GAIN7
SATURATION7
HUE7

[]SELECT[]BACK


11

PAN/TILT SPEED: 1，2，3，4，5，6，7，8
（the bigger the number is, the faster the
speed is. The speed is the fastest when in 1x
zoom compared to other zooming times）.
PTZ TRIG AF: ON, OFF (auto focus during
PAN, TILT,Zoom motion).
RATIO SPEED：ON, OFF(set the PTZ speed
with the relatively magnification, once it set as
ON, the large the magnification, while the
slower the PTZ speed.
POWER UP ACTION(: PRESET 1, PRESET
2, PRESET 3, PRESET 4, PRESET 5,
PRESET 6, PRESET 7, PRESET 8, PRESET
9, HOME.
SYSTEM MENU

ADDRESS：1, 2, 3, 4, 5, 6, 7.
PROTOCOL：VISCA, PELCO-D, PELCO-P.
BAUD RATE：2400, 4800, 9600, 38400.
VIDEO FORMAT：1080P60, 1080P50,
1080P30, 1080P25, 1080I60, 1080I50,
720P60, 720P50.
MOUNT MODE：STAND, CEILING.
LANGUAGE：ENGLISH, CHINESE.
STATUS MENU

See the info (address, protocol, baud rate,
video format, mount mode, image version and
firmware version) of the current camera.
<STATUS>
ADDRESS1
PROTOCOLVISCA
BAUDRATE9600
VIDEOFORMAT1080I50
MOUNTMODESTAND
FIRMWAREVER1.0.19

[]BACK
<SYSTEM>
ADDRESS1
PROTOCOLVISCA
BAUDRATE9600
VIDEOFORMAT1080I50
MOUNTMODESTAND
LANGUAGEENGLISH

[]SELECT[]BACK
<PANTILTZOOM>
PAN/TILTSPEED 8
PTZTRIRAFOFF
RATIOSPEEDON 
POWERUPACTIONPRESET9

[]SELECT[]BACK



12
RESTORE DEFAULTS

RESTORE DEFAULTS option is used to reset
all menus to default value.
Press to confirm; press to cancel
and return to previous menu.
List of Special Preset
Commands
Preset
No. Function
93
Cruise, camera switches among
saved 0~29 presets repeatedly and
sequentially in fixed interval.
95 Get into menu
96 Delete all presets
99 Reboot the PTZ
100 Video format: 1920X1080P50
101 Video format: 1920X1080P25
102 Video format: 1920X1080I50
103 Video format: 1280X720P50
105 Video format: 1920X1080P60
106 Video format: 1920X1080P30
107 Video format: 1920X1080I60
108 Video format: 1280X720P60
<RESTOREDEFAULTS>
PRESSOKCONFIRM
PRESSBACKCANCEL




[]BACK


13
Network Setting
Quick Guide
The camera can be accessed and controlled
via the following ways:
Client software IPCamConf: camera search
and control、network setting;
Initial Password: null
VLC: view of main and sub video stream;
Internet Explorer: view of main stream video
stream, camera control, network setting;
Name：admin
Password：null
SDK: To provider the second development
interfaces for camera connection and
control;
Onvif: support Onvif 2.1
Name: admin
password：123456
rtsp
1 Make sure PC and camera in the same
LAN;
2. Main stream：rtsp://IP:port/main.h264；
3 Sub stream：rtsp://IP:port/sub.h264；
4 The IP and port number can be checked
with IPCamConf software
Internet Explorer
1 Make sure PC and LTC in the same LAN;
2 support Windows 7 and above system，not
support Windows XP
3 Input IP address+ port number 88 (default is
88) in the IE address bar:
http://IP:88, such as:
http://192.168.18.229:88;
4 Install plugin;
SDK
The disc includes:SDK_Demo, SDK_Doc,
SDK_Lib
IPCamConf
Please refer to P14


14
IPCamConf
Setup IPCamConf from the disc in the packing, and connect the camera to the same LAN, then
enter the main interface as following.
Pic 1-1
Main interface includes：System menu、camera list、video control、video view、camera subject
information.
●System menu：The entrance to above 5 major function setting;
Pic 1-2
●Camera list: The software will auto search all devices from the same network and list all those
found in the camera list. Press the Search button and the software will search again.