ITC Power SL-S400 User manual

User Guide
Solar light Tower
SL-S400

CONTENTS PAGE
NO.S
1SAFETY 1-2
2 ASSEMBLY 4 - 7
3 STARTING PROCEDURE 8
4 STOPPING PROCEDURE 9 10 -
5 CHARGER
OPERATING INSTRUCTIONS
11
6
7 WIRING DIAGRAM
12
13 - 14

1.1 General Safety Notes.
1.2 The operator of the machine is responsible for, and has a duty of care in making sure
that the machine is operated safely and in accordance with the instructions in this user
manual. Keep the manual safe and pass it on if the machine is loaned or sold to another
user.
1.3 Please note the following safety points.
1.4 The machine should never be left it in a condition which would allow an untrained or
unauthorised person/s to operate this machine.
1.5 All due care and diligence should be taken by the operator for the safety of and with
regard to those around whilst using the machine.
1.6 Some or all of the following - warning signs, symbols and/or PPE pictograms may
appear throughout this manual. You MUST adhere to their warnings. Failure to doso
may result in personal injury to yourself or those around you.
DANGER
Indicates a hazard, which, if not avoided, could result in serious injury or death.
WARNING
Indicates a hazard, which, if not avoided, could result in serious injury.
CAUTION
Indicates a hazard which, if not avoided, might result in minor or moderate injury.
1.7 READ and keep the manual safe and pass it on if the machine is loaned or sold to
another user.
1.8 You MUST fully understand all instructions to ensure you use and operate the
machine safely.
1.9 Appropriate Personal Protective Equipment (PPE), MUST be worn at all times when
operating or repairing the machine.
1

1.10 Specification for storage, maintenance and safety protection of lithium batteries
1.11. Short term storage: when the lithium battery is not used for a short time (e.g.
within 6 months), the original battery manufacturer shall store the battery in a dry, non
corrosive gas place with a temperature and humidity of - 20°C~35°C 65 ± 20%. If the
temperature and humidity is higher or lower than this temperature and humidity, the
metal parts of the battery will rust or the battery will leak
1.12. Long term storage:
1.12.1. If the lithium battery is not used for a long time (e.g. more than 6 months), it shall
be charged with 50%~70% of the power, removed from the instrument and stored in a
dry and cool environment, and the battery shall be charged every 3 months to avoid too
long storage time, low power due to self discharge of the battery and irreversible capac-
ity loss.
1.12.2. The self discharge of lithium battery is affected by ambient temperature and
humidity. High temperature and humidity will accelerate the self discharge of battery. It
is recommended to store the battery in a dry environment of 10°C~25°C and 65 ± 20%.
1.13. Charging and charging capacity control:
1.13.1 charging method: ①the original manufacturer supplied by the battery uses
special battery equipment; ②the customer or user charges the battery in the instrument
and equipment. Generally, the lithium battery has relatively complete protection function
(with protective plate), there are not many other requirements for battery charging, but in
order to prevent safety problems caused by overcharge of the protective plate and
failure of the protective function, it is not recommended to charge for a long time. The
battery shall be taken out after it is fully charged. In addition, the original charger or the
charger attached to the battery must be used during charging, and the operation and
use must be carried out according to the instructions, otherwise the battery may be
damaged or even dangerous;
1.14. Heating treatment method: during charging and discharging (in use) it will generate
heat, but the temperature is usually below 60 degrees. The temperature of the battery
will reach hundreds or hundreds of Baidu in the internal or external short circuit state. At
this time, the battery must be isolated and placed in the sand. Pay attention not to touch
the battery directly by hand, otherwise it will be scalded. When the battery temperature
drops to the normal temperature, it will be scrapped.
Combustion or explosion treatment method: in case of combustion or explosion, it is
very dangerous, and personnel must stay away from it; battery combustion will not
produce open fire, which is usually caused by the ignition of nearby inflammables or
outer packaging boxes due to high temperature. On the premise of taking protective
measures, such as the fire extinguishing method of single or very few battery combus-
tion or explosion: directly cover the burning or explosive battery with sand It is a
large-area combustion. Use dry powder fire extinguisher to extinguish the fire. It is
strictly prohibited to use water to extinguish the fire, because water will cause battery
short circuit.
2

Item Description Quantity
1LEDLamp 4
2Mast 1
3M10x30Bolt 6
4Ø10Washer 6
5 Ø10 Spring 6
SL-S400
1
2
3
4
5
3
2. ASSEMBLY

Item Description Quantity
6
7
8
9
10
11
12
13
Transport Handle 1
Ø12 Washer 1
M12x30 Bolt 1
M5x16 Flange Bolt 2
Circuit Breaker Box 1
Electrical Box for Lamps 1
M6x16 Flange Bolt 2
Stabilisers 1
6
7
8
11
12
9
10
13
SL-S400
4

Item Description Quantity
14 M12x25 Bolt 8
15 Ø12 Washer 8
16 Ø12 Spring 8
14,15,16
SL-S400
5

17
Item Description Quantity
17 M8 x20 Bolt 4
SL-S400
6

SL-S400
7

NOTE
The lighting tower should not be used if the wind speed is above 31mph (50kph).
Only use the lighting tower on firm, flat and level ground.
2.0 Place the lighting tower in the area where lighting is needed.
2.1 Press down the brake and open the stabilisers.
2.2 Adjust the angle of the LED lamps.
2.3 Rotate the mast handle clockwise.
When the mast reaches its maximum height, the safety lock pin will automatically lock
the mast.
DO NOT shake the handle vigorously to avoid damaging the mast.
8
210°

2.4 Connect the lighting tower plug to the
2.5 Turn on the lighting power switch.
3.0 Turn off the lighting tower switch.
3.1
9
inverter and switch on the inverter breaker to ON.
Switch off the INVERTER breaker.

3.2 Pull out the safety lock pin and rotate the mast handle anti-clockwise until the mast is
fully retracted.
3.3 Close the stabilisers and press the brake downwards to release.
10
1
2

5. CHARGER
SOLAR CHARGING
MAINS charging
5.4 Switch on SOLAR breaker to charge battery
5.1 Loosen the knob, adjust the Angle of the solar panel, then lock the knob.
5.5 Swich off mains breaker
5.6 Plug to inverter input
5.7 Switch on INPUT breaker
5.8 Switch on mains breaker
5.2 Loosen the lock pin and pull out the solar panel sideways
5.3 Plug to 3 sockets
1 2 3 4
x2
SOLAR INPUTINVERTER
x3
1 2 3 4
SOLAR INPUTINVERTER
AC220V
INPUT
ON
OFF
11

6.1 The lighting tower must be placed on firm, flat and level ground.
6.2 The vertical inclination between the lighting tower and the ground should not exceed
more than 5 degrees.
6.3 The wind speed should not exceed 31mph (50kmh).
<5°
12
6. OPERATING INSTRUCTIONS

7. WIRING DIAGRAM
L N
BATTERY
MPPT
CONTROLLER 40A B+ B-
SOLAR INPUT
+-
+54V,8A
LOAD
Solar series
13

7. SPECIFICATION
L N
BATTERY
B+ B-
SOLAR INPUT
+-
+18V,24A
Solar
parallel
LOAD
MPPT
CONTROLLER 40A
14
7. WIRING DIAGRAM

Light Tower
Model Number SL-S400
Light Coverage 1500m2
Lamps LED
Lamp Wattage 4x100w
Life Expectancy 30000hrs
Mast Vertical Manual
Max Height 5m
New weight 170Kg
Dimensions (L x W x H) 1170 x 880 x 1950mm (mast down)
15

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.
No.7 Rongsheng Road,Cuibei,Henglin Town,
Changzhou City,Jiangsu Province,P.R.China
Tel [phone] Fax [phone]
Email:[email protected]
Http://www.itcpowerworld.com