Jack & June Haven II Playset User manual

2L-7985-00
817 Maxwell Avenue • Evansville, IN 47711 • 1-800-GO-SWING • www.escaladesports.com • ©2021 Escalade Sports
Haven II Playset
(JJ-Haven-II)

Choosing A Location For Your Playset
Maintaining Your Playset
Do not install home playground equipment indoors,
or over concrete, asphalt, packed earth, grass, carpet
or any other hard surface. A fall onto a hard surface
can result in serious or fatal injury.
Responsible on-site adult supervision is one of the
most important contributions to children’s safety that
you can make. Jack & June strongly recommends on-
site adult supervision of children of all ages. Safe
swinging and climbing skills need to be taught to
children, just like any other physical activity.
The weight limit for any single user on Jack & June
play equipment is 150 pounds. Limit the number of
users to one on each swing. The tower portion of the
play system will accommodate four (4) additional
users.
When the time comes to disassemble and dispose of
the play equipment, do so in such a way that no
hazards will exist at the time the equipment is
discarded.
When selecting your structure site, always keep the
child’s safety in mind. Here are some recommendations
to help you create a safe play area.
A. The playset should be located on level ground. The
stationary components such as ladders and slides are
REQUIRED to be a minimum of six feet from any structure
or obstruction such as a fence, garage, house, tree or
overhanging branches, electrical wires or clotheslines.
Any swinging equipment is also to be a REQUIRED
minimum distance twice the height of the swing beam
away from these obstructions or structures as well. We
also recommend that you do not install your playset
near a lake, river, swimming pool or other water hazard.
B. The U.S. Consumer Product Safety Commission (CPSC)
recommends that you install and maintain a resilient
surface under your play equipment. The CPSC’s
Consumer Information Sheet for Playground Surfacing
Materials at the end of this manual. A resilient surface,
should be installed after the equipment has been
completely assembled according to these instructions.
The equipment must rest on solid ground. Please note
that this product has a maximum fall height of 8’.
Welcome to our family of ready-to-build backyard play equipment. Jack & June playsets are designed with ease of
assembly in mind and we provide these step-by-step installation instructions.
After reading the information below, locate your structure site and carefully unpack parts. As you unpack your playset,
keep the parts identification sheet handy and become familiar with each part before beginning assembly. Remember that
a little extra time spent familiarizing yourself with the parts and instructions before you begin will help you avoid mistakes
and save you time later.
Here are some maintenance tips required to insure safe enjoyment of your equipment for years to come.
A. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed,
swing seats, chains, ladders, slides, rope and wood components for signs of deterioration and replace if necessary.
B. On a yearly basis, we recommend that you coat your playset with a sealant or preservative. You may also want to spot
sand any areas prior to sealing. Be sure that the sealant you select is non-toxic and child safe.
C. Do not use line trimmers or “weed eaters” around your play equipment. The line will remove both stain and wood
from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited
warranty.
D. Remove plastic swing seats and take indoors or do not use when the temperature drops below 0º F.
If you have any questions about your playset, or are in need of replacement parts, call 1-800-GO-SWING.
Please keep these instructions for future reference.
2
I N T R O D U C T I O N

In Addition, Adults Must:
• Not to walk close to, in front of, behind, or between
moving items.
• Not to twist the swing ropes, or loop them over the
top support bar, since this may reduce the strength
of the rope.
• Not to swing empty swing seats.
• Not to swing sideways into the path of adjacent
swings.
• Not to use the equipment in a manner other than
that for which it is intended.
• Not to get off the equipment while it is
in motion.
• Not to jump off the tower.
• Not to climb or swing when they are wet or when the
equipment is wet.
• Not to stand in the swing seats.
• Not to ride or leave bicycles or other toys in the
swing area.
• Not to use hammers, saws, nails, or wrenches on
the equipment.
• Not to swing so high that chains become slack, or
above the height of the swing support.
• Not to jump on a slide.
• Not to climb on top of the swing support.
• Not to attach to the playground equipment any item
that is not specifically designed for use with the
equipment, such as (but not limited to) jump ropes,
clotheslines, pet leashes, cables, and chains. These
may become strangulation hazards.
• To sit in the center of the swings with their full.
weight on the seats.
• To hold on to swings and climbers with.
both hands.
• To slide feet first, never head first..
• To watch for other children while swinging or playing.
near the equipment.
• Limit climbing and swinging heights to each child’s
ability.
• Verify that suspended climbing ropes are secured at
both ends.
• Verify that suspended climbing ropes cannot be
looped back on themselves.
• Dress children appropriately for play. Use well-fitting
shoes that do not have slippery soles.
Avoid ponchos, scarves, hoods, loose-fitting clothing,
neckties, and any clothing with a drawstring. Serious
injury could result should any part of the children’s
clothing become entangled in the equipment.
• Do not allow children to play wearing helmets.
• Remember that children are inventive. When they
develop games that are unsafe, be alert and change
the rules.
Teach Children:
3
S A F E T Y I N S T R U C T I O N S

3/8” x 6-1/2” HEX BOLT
PG-HW-B001
(2)
H1
H2
H3
H4
H5
H8
H6 H7
H9
H11
3/8” NYLON LOCKNUT
PG-HW-N001
(14)
3/8”-16 x 1/2” T-NUT
PG-HW-N002
(7)
3/8” FLAT WASHER
PG-HW-W004
(29)
#10 FLAT WASHER
PG-HW-W001
( )19
5/16” FLAT WASHER
PG-HW-W003
(54)
H10 1/4” FLAT WASHER
PG-HW-W002
(22)
3/8” x 1” SOCKET HEAD SCREW
PG-HW-B008
(7)
3/8” x 5-3/4” HEX BOLT
PG-HW-B024
(10)
3/8” x 7” HEX BOLT
PG-HW-B012
(1)
3/8” x 3-3/4” HEX BOLT
PG-HW-B025
(1)
4
H A R D W A R E I D E N T I F I E R

5/16” x 3” HEX LAG SCREW
PG-HW-L004
(6)
H14 1/4” x 4.5” HEX LAG SCREW
PG-HW-L002
(22)
H15
5
H12
5/16” x 2.5” HEX LAG SCREW
PG-HW-L003
(39)
H17
H27
PG-HW-L001
(30)
1/4” x 1.5” HEX LAG SCREW
PG-HW-L018
5/16” x 5” HEX LAG SCREW
(1)
5/16” x 1.5” HEX LAG SCREW
PG-HW-L021
(30)
H27
H A R D W A R E I D E N T I F I E R
H13 5/16” x 3.5” HEX LAG SCREW
PG-HW-L020
(8)

H18 H19
H20 H21
H23 #8 x 3” FLAT HEAD WOOD SCREW
PG-HW-S005
( )22
#8 x 1.5” FLAT HEAD WOOD SCREW
PG-HW-S003
(84)
#10 x 1” ROUND HEAD SCREW
PG-HW-S001
(4)
#8 x 2” FLAT HEAD WOOD SCREW
PG-HW-S004
( )140
H22 #8 x 2.5” FLAT HEAD WOOD SCREW
PG-HW-S009
(22)
#10 x 1.25” ROUND HEAD SCREW
PG-HW-S002
( )29
6
H22 #8 X 2’’ 1/2 PH FLAT HD WDSCRW
PG-HW-S009
(12)
H A R D W A R E I D E N T I F I E R

P A R T S L I S T ( N O T A C T U A L S I Z E )
94” DECK POST
PG-44-0077
(1)
189.5” DECK POST
PG-44-0078
(2)
9 96” DECK POST
PG-44-0079
(4)
3
83.5” DECK POST
PG-44-0080
(1)
7
2
SHORT LOWER HORIZONTAL
SUPPORT (2 HOLE)
(1)
SHORT LOWER HORIZONTAL
SUPPORT (1 HOLE)
PG-14-0043
(1)
1 2 3
4 5 6
PG-14-0042

LOWER HORIZONTAL SUPPORT
(2 HOLE)
PG-14-0022
(1)
LOWER HORIZONTAL SUPPORT
(1 HOLE)
PG-14-0023
(2)
HORIZONTAL POST BRACE
(ONE HOLE)
PG-14-0024
(3)
PANEL SUPPORT
PG-12-0001
(10)
DECK STEP
PG-14-0029
(5)
DECK SUPPORT
PG-24-0068
(11)
16
11 PG-14-0026
(4)
RAFTER
PG-14-0027
(1)
RAFTER
(W/ROPE HOLE)
PG-14-0028
(1)
97 8
12 13
14 15
8
TIPS:
To help you assemble Deck
Support (#16) to Deck Posts, and
other assemblies.
17 Assembly Aid Board
(2)
DECK END
P A R T S L I S T ( N O T A C T U A L S I Z E )
UPPER POST BRACE
PG-24-0075
(1)
10

UPPER ROOF RAFTER RIGHT
PG-24-0069
(2)
UPPER ROOF RAFTER LEFT
PG-24-0070
(2)
DECK STEP SUPPORT
PG-12-0002
(2)
ROOF CAP
PG-44-0083
(1)
25
26 27
28
18
SIDE PANEL
PG-PAN-027-021-02
(4)
19
SWING BEAM BRACE
PG-AC-0040
(2)
23
UPPER ROOF
PG-AC-0038
(2)
SWING BEAM
PG-46-0009
(1)
20
SWING BEAM LEG
PG-44-0084
(2)
21
SWING BEAM SUPPORT
PG-44-0085
(1)
22
29
24 SIDE PANEL W/ HOLE
PG-PAN-027-021-01
(1)
9
P A R T S L I S T ( N O T A C T U A L S I Z E )

LADDER LEG RIGHT
PG-24-0086
(1)
LADDER LEG LEFT
PG-24-0087
(1)
LADDER STEP
PG-26-0031
(3)
Slide Rail
(4)
35
33
34
39
36 37
(1)
31
(1)
32
PG-26-0032
(2)
30
10
PG-23-0004
Slide Base Block 38 Long Slide Side Long Slide Plastic
Slide Spacer
PG-23-0002
(2) 3M-9144-00
3M-9143-00
21
PG-33-0001
Upper Slide
Support Center
PG-44-0088
QTY. 1
Slide Upper Spacer
Slide Base
Block Center
QTY. 1
QTY. 2
PG-26-0033
P A R T S L I S T ( N O T A C T U A L S I Z E )

122" CLIMBING ROPE
PG-AC-0043
(1)
45 48
CLIMBING ROCK
PG-AC-0044
(3 RED)
NAME PLATE
PG-AC-0039
(1)
44
43
SPRING CLIP
PG-AC-0047
(4)
*Packed with #44
Belt Swing
46 BELT SWING (54”)
PG-AC-0045
(2)
47
47
DUCTILE SWING HANGER
PG-AC-0046
(4)
11
40
PG-DEK-027-021
(3)
(4 YELLOW)
P A R T S L I S T ( N O T A C T U A L S I Z E )
Deck Panel Assembly

H24 H11
TELESCOPE
PG-AC-0048
(1)
51
52 HANDLE
PG-AC-0049
(4)
53 SHIPS WHEEL
PG-AC-0050
(1)
5/16” FLAT WASHER
PG-HW-W003
(1)
5/16” x 2” HEX LAG SCREW
PG-HW-L007
(1)
H20 #8 x 1.5” FLAT HEAD WOOD SCREW
PG-HW-S003
(2)
12
H10 PG-HW-W002
(8)
1/4” x 2” HEX LAG SCREW
PG-HW-L022
(8)
H28
P A R T S L I S T ( N O T A C T U A L S I Z E )
1/4” FLAT WASHER

13
PG-24-0073
QTY. 2
PG-14-0031
QTY. 1
55
50
49
PG-14-0032
QTY. 7
54
CLIMBING WALL LEG
CLIMBING WALL BOARD
WITH NO HOLE
CLIMBING WALL BOARD
WITH ROPE HOLE
PG-14-0030
QTY. 6
CLIMBING WALL BOARD
WITH ROCK HOLE
P A R T S L I S T ( N O T A C T U A L S I Z E )

14
PARTS REQUIRED
PANEL SUPPORT ( )8
14
14 14
25
H21
H21
#8X2” FLAT HEAD WOOD SCREW
PG-HW-S004
( )24
SIDE PANEL ( )4
25
STEP 1:
Assemble two #14 Panel Supports onto #25 Side Panel using six H21 Screws as
shown.
FLUSH FLUSH
FLUSH
FLUSH
FLUSH

15
PARTS REQUIRED
DECK END ( )4
11
H20
H20
#8X1.5” FLAT HEAD WOOD SCREW
PG-HW-S003
(24)
H20
11
STEP 2:
Assemble one #11 Deck End onto STEP ONE Side Panel assembly using six H20 Screws as
shown.
Repeat procedure STEP ONE and STEP TWO for the other Side Panel assemblies.
NOTE: The back of Part 11 should be flush with the back of the Side Panel Assembly.

16
289.5" DECK POST (2)
LOWER HORIZONTAL
SUPPORT
(1 HOLE) (1)
5
H11 PG-HW-W003
(3)
H17
H17
5/16” x 2.5” HEX LAG SCREW
PG-HW-L003
(3)
DECK SUPPORT (2)
16
H14
H14
1/4” x 4.5” HEX LAG SCREW
PG-HW-L002
(2)
H10 1/4” FLAT WASHER
PG-HW-W002
(2)
PARTS REQUIRED
H23 #8x3” FLAT HEAD WOOD SCREW
PG-HW-S005
( )2
STEP 3:
Assemble one #5 Lower Horizontal Support onto
#2 and #5 Deck Posts using four H17 Screw and
four H11 Washers as shown. IMPORTANT
NOTE! Deck Posts and Lower Horizontal
Support must 90 degree.
90°
STEP 4:
Assemble one #16 Deck Support using two
H14 Screw, two H10 and two H23 as
shown.
IMPORTANT NOTE:
1. Make sure #2 and #5 Deck Post position
is as shown for correct assembly.
2. Make sure you measure and mark the
assembly location as shown in diagram on
#2 and #5 Deck Post for correct assembly.
17 ASSEMBLY AID BOARD (2)
ASSEMBLY TIP!
Use 2 ASSEMBLY AID boards to help
you assemble #16 Deck Support.
5
16
5
2
42’’
DETAIL A

17
PARTS REQUIRED
8
HORIZONTAL POST BRACE
(ONE HOLE) ( )1
8
H11
H11
5/16” FLAT WASHER
PG-HW-W003
(2)
H17
H17
5/16” x 2.5” HEX LAG SCREW
PG-HW-L003
(2)
STEP 5:
Make sure #5 facing up before you start the assembly.
Assemble one #8 Horizontal Post Brace using
two H17 Screw and two H11 Washer as shown.
IMPORTANT NOTE:
Make sure #5
Support facing up on this assembly
step.
Lower Horizontal
FLUSH
8
8
5

H17
H17
H14
H14
7
21’’
21’’
H23
H23
H11 5/16” FLAT WASHER
PG-HW-W003
(4)
5/16” x 2.5” HEX LAG SCREW
PG-HW-L003
(4)
1/4 x 4.5” HEX LAG SCREW
PG-HW-L002
(4)
H10 1/4” FLAT WASHER
PG-HW-W002
(4)
#8x3” FLAT HEAD WOOD SCREW
PG-HW-S005
(4)
PARTS REQUIRED
LOWER HORIZONTAL SUPPORT
(1 HOLE) (1)
7
DECK SUPPORT (2)
16
16
96" DECK POST (2)
3
3
3
83.5" DECK POST (1)
4
4
H11
H10
56’’
IMPORTANT NOTE:
1. Make sure #3 and #4 Deck Posts are
positioned as shown for correct assembly.
2. Make sure you measure and mark the
assembly location as shown in diagram on
#3 and #4 Deck Post for correct assembly.
90°
90°
STEP 7:
Assemble two #16 Deck Supports using
four H14, four H10 and four H23 as shown.
ASSEMBLY TIP!
Use 2 ASSEMBLY AID boards to help you
assemble #16 Deck Support.
NOTE!
17
STEP 6:
Assemble one #7 Lower Horizontal Support
onto #3 and #4 Deck Posts using four H17
Screws and four H11 Washers as shown.
IMPORTANT NOTE! Deck Posts and Lower
Horizontal Support must at 90 degree angle.
ASSEMBLY AID BOARD (2)
Bigger Counter Sunk
hole faces DOWN.
Smaller hole faces UP
for correct assembly.
18

H17
H17
H14
H14
21’’
21’’
H23
H23
16
H11 5/16” FLAT WASHER
PG-HW-W003
(4)
5/16” x 2.5” HEX LAG SCREW
PG-HW-L003
(4)
1/4 X 4.5” HEX LAG SCREW
PG-HW-L002
(6)
H10 1/4” FLAT WASHER
PG-HW-W002
(6)
#8x3” FLAT HEAD WOOD SCREW
PG-HW-S005
(6)
PARTS REQUIRED
7
94" DECK POST (1)
1
1
3
3
96" DECK POST (2)
3
H11
H10
56’’
42’’
LOWER HORIZONTAL SUPPORT
(1 HOLE) (1)
7
DECK SUPPORT (3)
16
IMPORTANT NOTE:
1. Make sure #1 and #3 Deck Post position
as per diagram shown for correct assembly.
2. Make sure you measure and mark the
assembly location as shown in diagram on
#1 and #3 Deck Post for correct assembly.
STEP 8:
Assemble one #7 Lower Horizontal Support
onto #1 and #3 Deck Posts using four H17
Screws and four H11 Washers as shown.
IMPORTANT NOTE! Deck Posts and
Lower Horizontal Support must 90 degree.
90°
90°
STEP 9:
Assemble four #16 Deck Support using
eight H14 Screw, eight H10 and eight
H23 as shown.
ASSEMBLY TIP! Use 2 ASSEMBLY AID boards
to help you assemble #16 Deck Support.
ASSEMBLY AID BOARD (2)
17
19

H17
PARTS REQUIRED
Note:
6
H11
H11
5/16” FLAT WASHER
PG-HW-W003
(4)
5/16” x 2.5” HEX LAG SCREW
PG-HW-L003
(4)
STEP 9 ASSEMBLY
STEP 7 ASSEMBLY
STEP 10:
With the help of other adults, Assemble one #6 Short Lower Horizontal Support using
four H17 screws and four H11 Washers as shown in diagram. Make sure to locate
and assemble #6 Lower Horizontal Support as shown in the “CORRECT” diagram.
20
6
STEP 7 ASSEMBLY STEP 9 ASSEMBLY
Counterbore/bigger
hole faces in.
At least 3 people are
needed to complete
assembly.
DETAIL A
NOTE
6
6
CORRECT
INCORRECT
SHORT LOWER HORIZONTAL
SUPPORT (2 HOLE)
6
6
H11
H17