Jacobsen LDEA130 User manual

Mastiff 91
RJ 100 / 02 2005
24481G-NL (rev.3)
Series:BY & CJ - Engine type: Honda GH 280
Product codes: LDEA130 & LDEA140
WAARSCHUWING: Bij verkeerd gebruik kan deze machine
ernstiglichamelijkletselveroorzaken.Degenendiedemachine
gebruiken en onderhouden moeten worden getraind in het
juiste gebruik ervan, worden gewaarschuwd voor de
gevaren ervan en behoren de volledige handleiding
aandachtig te lezen alvorens de machine bedrijfs-klaar te
maken, te bedienen, af te stellen en/of te onderhouden.
WARNING:If incorrectly usedthis machine cancause severe
injury. Those who use and maintain this machine should be
trained in its proper use, warned of its dangers and should
read the entire manual before attempting to set up, operate,
adjust or service the machine.
Safety and Operation / Maintenance and Parts Manual
Veiligheids-, Bedienings-, Onderhouds- en Onderdelenhandleiding

©2003, Ransomes Jacobsen Limited. All Rights Reserved

GB-1
RANSOMES MASTIFF 91
SAFETY, OPERATORS, MAINTENANCE AND PARTS MANUA
L
Contents
CONTENTS PAGE
IMPORTANT 2
SPARES STOCKING GUIDE 3
PRODUCT IDENTIFICATION 4
HOW TO USE THE PARTS MANUAL 5
SAFETY INSTRUCTIONS 6
SPECIFICATIONS 9
EC DECLARATION OF CONFORMITY 10
CONTROLS 12
OPERATION OF THE MACHINE 14
LUBRICATION 18
MAINTENANCE 21
ADJUSTMENTS 23
ACCESSORIES 27
STORAGE 28
GENERAL ADVICE 28
CORRECTION OF MINOR FAULTS 29
ELECTRICAL SYSTEM 30
GUARANTEE 32

GB-2
RANSOMES MASTIFF 91
SAFETY, OPERATORS, MAINTENANCE AND PARTS MANUA
L
IMPORTANT
IMPORTANT: This is a precision machine and the service obtained from it depends on the way it is
operated and maintained.
This operators manual should be regarded as part of the machine. Suppliers of both new and
second-hand machines are advised to retain documentary evidence that this manual was provided
with the machine.
This machine is designed solely for use in customary grass cutting operations. Use in any other
way is considered as contrary to the intended use. Compliance with and strict adherence to the
conditions of operation, service and repair as specified by the manufacturer, also constitute
essential elements of the intended use.
Before attempting to operate this machine, ALL operators MUST read through this manual and
make themselves thoroughly conversant with Safety Instructions, controls, lubrication and
maintenance.
Accident prevention regulations, all other generally recognized regulations on safety and
occupational medicine, and all road traffic regulations shall be observed at all times.
Any arbitrary modifications carried out on this machine may relieve the manufacturer of liability for
any resulting damage or injury.
Use of other than original or authorised Textron Turf Care & Specialty Products Spare Parts &
Accessories will void the warranty.

GB-3
RANSOMES MASTIFF 91
SAFETY, OPERATORS, MAINTENANCE AND PARTS MANUA
L
straPecivreS
l
airetaMtroppuSecivreS
rebmuNtraPnoitpircseDrebmuNtraPnoitpircseD
06134-45421renaelCriAA/N straPenignE launaM
D9562BBMk6rednilyCgnittuC1-1198-1512E srenwOenignE koobdnaH
8822FBMk9rednilyCgnittuC01900-79879 pohSkroWenignE launaM
A0107ABMedalBmottoB
SPARES STOCKING GUIDE
To keep your equipment fully operational and productive, Ransomes suggests you maintain a stock of the
more commonly used maintenance items. We have included part numbers for the additional support
materials and training aids.

GB-4
RANSOMES MASTIFF 91
SAFETY, OPERATORS, MAINTENANCE AND PARTS MANUA
L
AB
C
DE
A Machine Name
B Serial Number
C Year of Manufacture
D Machine Weight
E Engine Power
Fig.1
PRODUCT IDENTIFICATION

GB-5
RANSOMES MASTIFF 91
SAFETY, OPERATORS, MAINTENANCE AND PARTS MANUA
L
HOW TO USE THE PARTS MANUAL
ITEM NUMBER
Each part which is identified in the illustrations has an item number. Parts which do not have an item number may not be
readily identified in the illustration but are usually closely associated with the immediately adjacent part.
ASSEMBLIES
A complete assembly, e.g. a wheel motor or hydraulic motor or roll assembly, is listed as a complete item with subsequent
individual components listed separately.
The assembly is listed under it's part number with component parts being listed offset to the right, e.g:-
ITEM RANSOMES DESCRIPTION QTY REMARKS
PART NO.
4295 MBG2504 BRACKET 1
4296 MBG3848 LATCH 2
4298 450865 SCREW, M8 x 20, SCKT CSK HD 2
4300 450378 NUT, M8 NYLOC 2
4301 Wl001 Set Of Wheels 1
4301.1 008162130 • Wheel & Hub Assy 1 (Rear)
4301.2 008170390 • • Tyre 1
4301.3 008161830 • • Rim 1
4301.4 008169140 • • Hub Assy. 1
4301.5 008169150 • • Cap 1
4301.6 002993010 • • Lubricator 1
4301.7 008161990 • Wheel & Tyre 2 (Front)
4301.8 008170780 • • Tyre 2
4301.9 008161250 • • Rim 2
4302 001341110 Wheel Nut 12
It may not be possible to illustrate every item. With certain items purchased from outside suppliers some component parts
may not be available from Ransomes and may need to be specially ordered from the supplier.
QUANTITIES
Quantities shown are for one assembly or sub-assembly.
USING THE PARTS LIST
Determine the function and application of the part required. Turn to the main index page and select the appropriate
section. Locate the part on the illustration and parts list and read off the quantity from the appropriate MODEL column.
NUMERICAL INDEX
This is a summary of all part numbers used in the manual arranged in numerical sequence and showing the page and
item number under which the parts appear.
ORDERING OF SPARE PARTS
When ordering replacement parts, it is most important to quote the SERIAL NUMBER of the machine, PART NUMBER,
DESCRIPTION and QUANTITY required.
Any arbitrary modifications carried out on this machine may relieve the manufacturer of liability for any
resulting damage or injury.
Use of other than original or authorised Textron Turf Care & Specialty Products Spare Parts will void
the warranty.
ABBREVIATIONS
N/A Not Available
AR As Required

GB-6
RANSOMES MASTIFF 91
SAFETY, OPERATORS, MAINTENANCE AND PARTS MANUA
L
This safety symbol indicates important safety
messages in this manual. When you see this
symbol, be alert to the possibility of injury, carefully
read the message that follows, and inform other
operators.
SAFETY INSTRUCTIONS
OPERATING INSTRUCTIONS
Ensure that the instructions in this book are read
and fully understood.
No person should be allowed to operate this
machine unless they are fully acquainted with all
the controls and the safety procedures.
Never allow children or people unfamiliar with
these instructions to use this machine. Local
regulations may restrict the age of the operator.
SAFETY SIGNS
It is essential all safety labels are kept legible, if
they are missing or illegible they must be replaced.
If any part of the machine is replaced and it
originally carried a safety label, a new label must
be affixed to the replacement part. New safety
labels are obtainable from Ransomes dealers.
STARTING THE ENGINE
Before starting the engine check that the drives
are in neutral, guards are in position and intact,
and bystanders are clear of the machine. Do not
run the engine in a building without adequate
ventilation.
DRIVING THE MACHINE
Before moving the machine, check to ensure that
all parts are in good working order, paying
particular attention to the security of cutting blades.
Replace faulty silencers. Mow only in daylight or
good artificial light.
Always observe the Highway Code both on and off
the roads. Keep alert and aware at all times.
Remember that some people are deaf or blind and
that children and animals can be unpredictable.
Watch out for traffic when crossing or near
roadways.
Stop the blades rotating before crossing surfaces
other than grass.
Remove or avoid obstructions in the area to be
cut, thus reducing the possibility of injury to
yourself and/or bystanders. When moving the
machine backwards, take special care to ensure
that the area behind is clear of obstructions and/or
bystanders.
After striking a foreign object, inspect the machine
for damage and make repairs before restarting and
operating the equipment. If the machine starts to
vibrate abnormally, check immediately.
DO NOT carry passengers.
Keep in mind that the operator or user is
responsible for accidents or hazards occurring to
other people or their property.
While mowing, always wear substantial footwear
and long trousers. Do not operate the equipment
when barefoot or wearing open sandals.

GB-7
RANSOMES MASTIFF 91
SAFETY, OPERATORS, MAINTENANCE AND PARTS MANUA
L
TRANSPORTING
Do not transport with cutting mechanism rotating.
Operate the machine with due consideration of
road and surface conditions, inclines and local
undulations.
LEAVING THE OPERATING POSITION
Park the machine on level ground. Before leaving
the operating position, stop the engine and make
sure all moving parts are stationary. Disengage all
drives. When the machine is to be parked, stored
or left unattended, lower the cutting units unless
the transport locks are being used.
SLOPES
TAKE EXTRA CARE WHEN WORKING ON
SLOPES
Local undulations and sinkage will change the
general slope. Avoid ground conditions which can
cause the machine to slide. Keep machine speeds
low on slopes and during tight turns.
Ratchet driven machines free-wheel on downhill
slopes. Remember there is no such thing as a
"safe" slope. Travel on grass slopes requires
particular care, to guard against overturning.
BLOCKED CUTTING CYLINDER
Stop the engine and make sure all moving parts
are stationary. Apply brakes and disengage all
drives.
Release blockages with care. Keep all parts of the
body away from the cutting edge. Beware of
energy in the drive which can cause rotation when
the blockage is released.
Keep other people away from the cutting unit.
ADJUSTMENTS, LUBRICATION AND
MAINTENANCE
Read all the appropriate servicing instructions. Use
only the replacement parts supplied by the original
manufacturer.
When adjusting the cutting cylinders take care not
to get hands and feet trapped when rotating
cylinder. Make sure that other people are not
touching the cutting unit.
To reduce the fire hazard, keep the engine,
silencer and battery free of grass, leaves or
excessive grease. Replace worn or damaged
parts for safety.
When working underneath lifted parts or machines,
make sure adequate support is provided.
Do not dismantle the machine without releasing or
restraining forces which can cause parts to move
suddenly.
Do not alter engine speed above maximum quoted
in Engine Specification. Operating the engine at
excessive speed may increase the hazard of
personal injury.

GB-8
RANSOMES MASTIFF 91
SAFETY, OPERATORS, MAINTENANCE AND PARTS MANUA
L
When refuelling, STOP THE ENGINE, DO NOT
SMOKE. Refuel outdoors only. Add fuel before
starting the engine, never add fuel while the
engine is running. Use a funnel when pouring fuel
from a can into the tank. Do not spill fuel onto hot
components. If petrol is spilled, do not attempt to
start the engine but move the machine away from
the area of spillage and avoid creating any source
of ignition until petrol vapours have dissipated. If
the fuel tank has to be drained, this should be
done outdoors. DO NOT fill the fuel tank beyond
the bottom of the filler neck. Replace all fuel tank
and container caps securely. Store fuel in
containers specifically designed for this purpose.
When servicing batteries, DO NOT SMOKE, and
keep naked lights away. Do not place any metal
objects across the terminals. Allow the engine to
cool before storing in any enclosure. Never store
equipment with petrol in the tank inside a building
where fumes may reach an open flame or spark.
WHEN USING ON LOADING
RAMPS OR ON UNDULATING
GROUND ALWAYS ENSURE THAT
THE HANDLE IS ADJUSTED TO
GIVE ADEQUATE CLEARANCE
ABOVE THE LEGS. FAILURE TO
DO THIS COULD RESULT IN A
SITUATION WHERE THE
OPERATORS LEGS COME INTO
CAUTION
BATTERIES PRODUCE
EXPLOSIVE GASES AND
CONTAIN CORROSIVE ACID AND
SUPPLY LEVELS OF ELECTRICAL
WARNING
CALIFORNIA PROPOSITION 65
ENGINE EXHAUST, SOME OF ITS
CONSTITUENTS, AND CERTAIN
VEHICLE COMPONENTS
CONTAIN OR EMIT CHEMICALS
KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER
AND BIRTH DEFECTS OR OTHER
WARNING