JAKOB HATTELAND JH 20T01 MIL User manual

JH 20T01 MIL Industrial Color Display 1
User’s Manual
20,1 inch Industrial Color Display
JH 20T01 MIL
Jakob Hatteland Instrument AS

JH 20T01 MIL Industrial Color Display 2
JH 20T01 MIL User’s Manual
Document: User’s Manual
Revision: 9801
Order no: JH 20T01 MIL
Issued by: Jakob Hatteland Instrument A/S
for
Product: 20,1 inch Industrial Color Display
Type: JH 20T01 MIL
Table of Contents
Chapter 1 General Page
1.1 Introduction to JHI monitors and displays……………………… 4
1.2 About this manual………………………………………………. 4
1.3 General Description of the JH 20T01 MIL…………………….. 4
1.4 The JHI industrial CRT’s and TFT’s…………………………… 4
Chapter 2 Approvals
2.1 CE………………………………………………………………. 4
2.2 Declaration of Conformity ……………………………………… 5
Chapter 3 Precautions
3.1 Unpacking………………………………………………………. 6
3.2 Mounting………………………………………………………... 6
3.3 Recommended use……………………………………………… 6
3.4 Virus……………………………………………………………. 6
Chapter 4 Mounting Instructions
4.1 Rack version……………………………………………………. 7
4.2 Recommended binding screws…………………………………. 7
4.3 Mounting holes…………………………………………………. 7
Chapter 5 Hook Up
5.1 Power cable……………………………………………………. 7
5.2 Signal cable……………………………………………………... 7
5.3 Input signals……………………………………………………. 7
5.4 Video input…………………………………………………….. 8
Chapter 6 Connection
6.1 Connection alternatives………………………………………… 8
6.2 Connection to PC……………………………………………… 8
6.3 Connection to Mac…………………………………………….. 8
6.4 Connection to Video cards ……………………………………. 9
Chapter 7 Display Adjustment Control
7.1 Outside front panel controls……………………………………. 9

JH 20T01 MIL Industrial Color Display 3
7.2 Inside front panel controls………………………………………. 10
7.3 On Screen Manager Control…………………………………….. 11
Chapter 8 Trouble Shooting
8.1 General………………………………………………………….. 12
8.2 Symptoms and cure ……………………………………………. 12
Chapter 9 Technical Specification and drawings
9.1 Technical description…………………………………………… 13
9.2 Mechanical drawing……………………………………………. 15
Chapter 10 Tables - Pin assignment and timing
10.1 Pin assignment table ………………………………………… 16
10.2 Preset Signal Timing ………………………………………. 17
Chapter 11 Maintenance and Service…………………………… 18
Chapter 12 Accessory - OPTIONS
12.1 Front…………………………………………………………. 18
12.2 Cabinet……………………………………………………….. 18
12.3 Suspension brackets…………………………………………. 18
12.4 Touch Screen………………………………………………… 18
Chapter 13 Users own notes…………………………………….. 19

JH 20T01 MIL Industrial Color Display 4
Chapter 1 General
1.1 Introduction to JHI Monitors and Displays
JHI is one of the leading producers of industrial monitors and displays in the market. Our
industrial color monitors and displays provides you with the latest in technology. This means
that the monitor provides you with automatic compatibility with multiple operating platforms
and a vast array of graphics standards allowing resolution upgrades without upgrading the
monitor. The high quality of the monitors allows you to display professional applications with
clarity and enhanced color and image quality. Options are rack version for flush mounting and
the cabinet version for “stand alone” applications. Custom designed front, color and logo can
easily be adapted.
1.2 About this manual
This manual contains information needed for installation, power up and use of the display
JH 20T01 MIL. The manual contains also electrical, mechanical and inputs signal
specifications. All specifications in this manual, due to manufacturing, new revisions and
approvals, are subject to change without notice.
It is recommended that installation engineer and user of the display unit read this manual
before installation and use.
NB! This manual or parts of it must not be reproduced or copied without written permission
from the manufacturer - Jakob Hatteland Instrument AS
1.3 General description of the JH 20T01 MIL
The color display described in this manual are an industrialized version of high quality
products. The monitors allow you to display professional applications with clarity and
enhanced color and image quality. The combinations of the monitors plug and play capability,
high quality picture and the hardware construction of the mechanical parts and assembly will
satisfy a wide range of industrial environments.
1.4 The JHI industrial CRT’s and TFT’s
The JHI industrial CRT monitors and TFT displays offers the high-tech industry a complete
range of units. Jakob Hatteland Instrument has developed and produced industrial monitors
since 1987. All the units are stand alone CE approved units. A number of the products are
also Type Approved by several of the major classification societies.
Chapter 2 Approvals
2.1 CE
This product is partly tested according to the regulations according to the EMC directive and
found to be within the requirements given. Jakob Hatteland Instrument AS declares that this
product is in conformity according to information given in chapter 2.2 Declaration of
Conformity.

JH 20T01 MIL Industrial Color Display 5
2.2 Declaration of Conformity
(Declaration of Conformity doc.)

JH 20T01 MIL Industrial Color Display 6
Chapter 3 Precautions
3.1 Unpacking
Handle with care when transporting the display. Do not unpack the display before it is on the
site of use or installation. Although the device can stand on the edge this is not recommended
as the unit may fall over and damage may occur to the device.
It is recommended that you save the original box and packing materials for transportation or
shipment of this display.
3.2 Mounting
Ensure prior to installation that your mounting jig, console or other application are capable of
carrying the display. All four mounting screws applicable in the front of the monitor should
be used for fastening the device.
Also ensure that your fastening threads fits properly to the enclosed fastening screws.
3.3 Recommended use
For optimum performance when setting up and using the display please note the following:
Use 1280 x 1024 resolution at 60 Hz.
The optimum display position is away from direct sunlight.
Install the display just below eye level for the ideal viewing angle.
Allow adequate ventilation around the display so that heat can properly dissipate.
For optimum performance, allow 20 minutes for warm-up.
3.4 Virus
Some of the displays are delivered with a diskette.
Before installing the program from the disk you should READ THIS:
The enclosed disk is thoroughly checked for viruses. While every care is taken neither JHI nor
the producer of the diskette will accepts no responsibility for loss or damage occurred during
installation or use of the content on the diskette. You are strongly advised to have recent,
verified backups of your system files before installing new software. We further advise you to
check the diskette according to your own safety standards (anti virus check).

JH 20T01 MIL Industrial Color Display 7
Chapter 4 Mounting Instructions
4.1 Rack version
This rack version is provided with mounting holes making installation in rack or console in
precut cutouts easy.
4.1 Recommended binding screws
For safe mounting you should use the enclosed screws for fastening the device. If for some
reason the screws are not fitted for your application please ensure to use screws or other
fastening material of same strength.
4.1 Mounting holes
Fore easy mounting use the four (4) holes located nearby the two handles.
Chapter 5 Hook Up
5.1 Connecting Power
Ensure that the device are switched off prior to power hook up. Check your power source to
ensure that correct voltage are present. This device are equipped with an universal power
supply and need the following mains voltage to operate;
Input voltage: DC 12 - 36 V 50/60 Hz
Power cons. : 85 W
Interface: Std. Screw termination.
We recommend that you use the power cord supplied with the monitor for hook up.
5.2 Signal cable
Use the enclosed VGA cable for connecting the display to the computer. If a longer cable are
required you should use a high quality VGA signal cable for optimum signal transfer. Jakob
Hatteland Instrument can provide special designed high quality VGA cables in many different
lengths.
Ensure that the device are switched off prior to interface hook up. Check your interface
source to ensure that the right signals are present. Check out the tables with signal and
timing if you are unfamiliar with the signals.
5.3 Input signals
This monitor will apply to most known PC and Workstation signals. Hook up to your device
should normally cause no problem. See Chapter 6 Connection to computer for different
connection options.

JH 20T01 MIL Industrial Color Display 8
For more details regarding Pin Assignment Table, Signal Timing Charts or Preset Timing
Chart please turn to Chapter 10 Tables - Pin assignment and timing.
5.4 Video input
The video input can be done through the D-SUB connector mounted on the signal cable
directly mounted to the display.
1 x Mini D-SUB 15p female connector
NB! Always ensure that connected signal cables are properly mounted and that screw
coupling are used. This will ensure that the signal cable always are connected.
Chapter 6 Connection
6.1 Connection alternatives
There are several options for connecting this monitor to your computer. Depending on your
equipment and computer capability use one of the options below.
6.2 Connection to PC
This monitor comply with most common known PC computers. Your system has one of two
configurations:
1. The video controller is built into the computer
2. The video controller is in the form of a video card (sometime referred to as a
graphic card, video adapter, or graphics board.)
Both configurations have a video connector (or a CRT port). If you are not sure as to which
connectors is the video connector, consult your computer or video card manual. To attach the
monitor to your system, follow the instructions below.
1. Turn off the power to the display and computer.
2. If necessary, install the video card. For more information, refer to the manual
accompanying the card.
3. Connect the 15-pin mini D-SUB end of the MultiCable to the video connector of
your system..
4. Connect one end of the power cable to the display and the other end to the power
outlet.
5. Turn on the display and computer.
6. This completes the installation.
6.3 Connecting to Mac
This display comply with most Mac computers. Your system has one of two configurations:
1. The video controller is built into the computer.

JH 20T01 MIL Industrial Color Display 9
2. The video controller is in the form of a video card (sometimes referred to as a
graphic card, video adapter, or graphics board) installed in a Nu-Bus or PDS slot.
Both configurations have a video connector. If you are not sure as to which connector is the
video connector, consult your computer or video card manual. To attach the monitor to your
system, follow the instructions below.
1. Turn off the power to the display and computer.
2. If necessary, install the video card. For more information, refer to the manual
accompanying the card.
3. Connect the 15-pin mini D-SUB end of the MultiCable to the video connector of
your system.
4. Connect one end of the power cable to the display and the other end to the power
outlet.
5. Turn on the display and computer.
6. This completes the installation.
NB! Some Mac computers require a cable adapter, consult your dealer.
6.4 Connection to Video cards
If your computer or video card is not compatible with the monitors preset signals or has a
different pin assignment, refer to the steps below to determine if your system is compatible
with the monitor.
1. Turn off the power of the display and the computer.
2. Determine the video connector’s pin assignment of your video card.
3. Determine the output signal timing and level of your video card.
4. Check the pin assignment and signal timing charts of the video card and make sure
the display accepts these pin assignments and signal timings.
5. Connect the signal cable supplied with your video card to the display.
6. Connect on end of the power cable to the display and the other end to a power
outlet.
7. Turn on the display and computer.
8. Adjust size and position of the image to your preference.
9. This completes the installation.
Chapter 7 Display Adjustment Controls
7.1 Outside front panel controls
This display is provided with easy access main control for the user. On the display front right
side following controls are available;
Adjustment/control items Function/description
ON/OFF power switch - turns the display power on or off. When the power is on, the
LED is lit.

JH 20T01 MIL Industrial Color Display 10
CONT - adjust the image brightness in relation to the background.
BRIGHT - adjust the overall image and background screen brightness.
LED (Power Indicator Light) - located top left of the power switch is on and indicates the
display’s power mode. Each mode reduces the amount of
power used by the monitor. LED intensity can be adjusted, see
chapter 7.2 for information.
NOTE: The function CONT & BRIGHT adjustment adjusts the actual gain area adjusted by
the on-screen-manager control function
7.2 Inside front panel controls
Inside the front panel at the left side of the display there are available several push switches.
The analog switches offers the user a easy access for adjusting the picture. The controls
include the following options: Size, Position, image quality and reset to factory setting.
To adjust the picture and settings the On Screen Manager will appear on the display.
Fig. 7.2.1 Inside front panel controls
Description and function:
Control Main Menu Sub-Menu
EXIT Exits the OSM controls. Exit to the OSM controls
main menu.
CONTROL Moves the highlighted Moves the highlighted
area up/down to select one area up/down to select
of the controls. one of the controls.
CONTROL+/-Has no function. Moves the bar in the + or
- direction to increase or
decrease the adjustment
PROCEED Proceeds to selected menu Activates Auto Adjust
choice (indicated by the feature. In Display Mode,
highlighted area). Opens additional window.
RESET: The Resets all the controls Resets the highlighted
currently high-within the highlighted control.
lighted menu.