Jamex 7110 User manual

MODEL 7110/7112MODEL 7110/7112
CARD READERCARD READER
for afor a
Make & ModelMake & Model
COPYRIGHT 2006 by Jamex, Inc.COPYRIGHT 2006 by Jamex, Inc. All rights reserved worldwide.All rights reserved worldwide.
All of the information contained in this manual is the property of Jamex, Inc. This manual is providedAll of the information contained in this manual is the property of Jamex, Inc. This manual is provided
to purchasers and users of equipment sold by Jamex, Inc. in order to supply the technical informationto purchasers and users of equipment sold by Jamex, Inc. in order to supply the technical information
necessary to install, operate, and maintain that equipment. Permission is hereby granted tonecessary to install, operate, and maintain that equipment. Permission is hereby granted to
photocopy this manual if (a) both the original and the copies are used only in support of equipmentphotocopy this manual if (a) both the original and the copies are used only in support of equipment
sold by Jamex, Inc., and (b) if this notice is attached to each copy. No part of this document may besold by Jamex, Inc., and (b) if this notice is attached to each copy. No part of this document may be
reproduced by any means, other than as stated above, without the written permission of Jamex,reproduced by any means, other than as stated above, without the written permission of Jamex,
Inc.,2415 N. Triphammer Rd., Ithaca, NY 14850.Inc.,2415 N. Triphammer Rd., Ithaca, NY 14850.
Rev. January 2006Rev. January 2006
Jamex, Inc. - 2415 N. Triphammer Rd., Ithaca, NY 14850 - 800-289-6550Jamex, Inc. - 2415 N. Triphammer Rd., Ithaca, NY 14850 - 800-289-6550
www.jamexvending.comwww.jamexvending.com

TABLE OF CONTENTSTABLE OF CONTENTS
INTRODUCTIONINTRODUCTION
Equipment Features Page 2Page 2
Other Jamex Products
USER'S MANUALUSER'S MANUAL
Operating GuideOperating Guide Page 3-4Page 3-4
Power-up
Operation of the Vending System
Bypass Operation
Data ManagementData Management Page 5Page 5
Reading the Meters
INSTALLATION and SERVICE GUIDEINSTALLATION and SERVICE GUIDE
Installation & Set upInstallation & Set up Page 6Page 6
Unpacking the Vending System
Physical Mounting
Electrical Installation
Programming Your Jamex Model 7110Programming Your Jamex Model 7110 Page 6-8Page 6-8
Adjusting the Price Per Copy
Programming Value to Cards
MaintenanceMaintenance Page 9Page 9
Trouble-Shooting GuideTrouble-Shooting Guide Page 9Page 9
InstallationInstallation Page 10-11Page 10-11
Electrical Hook-up
Point-to-Point Wiring Diagram

1
INTRODUCTIONINTRODUCTION
Thank you for choosing a JamexJamex system for your vending needs. This manual provides instructions for operating
your Jamex Vending SystemJamex Vending System as well as technical information necessary to install and maintain the system. Please
keep this manual available and refer to it when calling for technical support.
Model 7110/7112 Stand Alone Card ReaderModel 7110/7112 Stand Alone Card Reader is one part of a complete system that facilitates vending through the
use of Stored-Value Cards rather than, or in addition to, the use of cash. The use of Stored-Value Cards can
increase security of your vended services by reducing the handling of cash. They may also add convenience for
patrons who prefer to carry one small card rather than a pocket full of cash for larger transactions.
In addition to the Stored-Value Cards, a complete Card Vending System includes the following four elements:
- A method of dispensing the Stored-Value Cards
- A control mechanism which reads the cards and enables the copier, computer printer,
fax machine, micro fiche reader, etc. ( Model 7110/7112 is a control mechanism)
- A method of encoding value, security information, and revenue tracking codes
onto the Stored-Value Cards
- A method of tracking revenue and accounting for vended services
For more information on Stored-Value Card Systems please contact your local business equipment dealer, or call
Jamex at 1-800-289-6550 or visit our webpage at www.jamexvending.com.

2
FEATURES OF YOUR MODEL 7110/7112FEATURES OF YOUR MODEL 7110/7112
Your Jamex Vending SystemJamex Vending System model 7110/7112 incorporates the following features:
!Accepts only exclusive proprietary cards, maintaining the high security of your system
!Programmable maximum card value of up to $999.999
!Price per copy is programmable in $.001 increments up to $99.999
!Up to four user groups (site codes)
!Bypass cards for staff and service use
!Full feature LCD display for card and bypass copies, and system accounting
!Exclusive management cards for setting prices and reading meters
!Mounting holes provided for secure installation
!Solid state copier interface with polarity - independent connections
ŽSturdy steel housing with beige textured powder-coat epoxy finish
ŽTwo year warranty with "overnight" shipment of warranty parts and toll free technical support
Extended features of the Model 7112:Extended features of the Model 7112:
!Ability to program value to cards using a Command Cash Card
!Dual price capabilities
The full family of Jamex products includes:The full family of Jamex products includes:
-single copy coin only vending systems
-multi copy coin only systems
-multi copy coin & bill vending systems
-"FAX ACCESS" for charging by the page for the use of a Fax Machine
-compatible mounting systems and stands
-print vending systems for computers and computer networks
-card systems: System 7000 Stored-Value magnetic stripe card systems
Jamex, “The Payment Method People”Jamex, “The Payment Method People”
Since 1981, JamexJamex has developed vending technology for a variety of applications. We look forward to
assisting people like you with ongoing innovations in revenue generation through vending.
Jamex is a manufacturer who believes in Service. Should you have any questions concerning your model
7110/7112 or other Jamex Vending SystemsJamex Vending Systems, please call your authorized JamexJamex dealer or JamexJamex
customer service at 1-800-289-6550, or visit our website at www.jamexvending.com.

3
OPERATING GUIDEOPERATING GUIDE
POWER - UPPOWER - UP
When first powered up, the LCD display on your 7110/7112 Jamex Vending SystemJamex Vending System will scroll the following
message ” JamexJamex, Inc. Copyrite © 1997 STANDALONE Ver “the date of the firmware version”. This will be followed by
the prompt “Insert Your Card”
OPERATION OF THE JAMEX 7110/7112 VENDING SYSTEMOPERATION OF THE JAMEX 7110/7112 VENDING SYSTEM
JamexJamex CopyCards are required for the operation of your Stand Alone Card Reader. These cards are ordered from
JamexJamex and are formatted to work with the Jamex reader. Jamex Stored Valued Copy Cards are white with blue
graphics. Management Cards are blue with white graphics. On the face of these cards are the words ”Copy Card”,
the JamexJamex logo and a stylized blue arrow. On the back of the card is a magnetic stripe which stores the security
coding that designates your cards as specific to your location, and the stored value which allows the patron to buy
services.
These cards may also be coded to differentiate between four distinct groups of users. These user groups are
sometimes referred to as Site Codes. The activity for each Site Code is tracked separately in the accounting
function of your 7110/7112. When a copy card is inserted into the 7110/7112 Card Reader it will determine that the
card is acceptable to that reader, record the activity, and determine what price to charge and to deduct from the
value stored on the card for the service purchased. Stored Value Cards are programmed with a Site Code. The
Site Code programed to the Stored Value Card must match one of the four Site Codes programmed to the Card
Reader. This security feature ensures that the Vend System is proprietary.
Begin a transaction by inserting a Copy Card arrow end first and face up into the card reader. The display will show
the value stored on the card. When this value meets or exceeds the vend price, the copier (micro fiche reader, fax
machine, etc) will be enabled. Each time the copier makes one copy, the value stored on the card will be
decreased by the cost per copy and the display will show the remaining value left on the card. The copier will
remain enabled as long as the value stored on the card remains at or above the vend price. When the patron is
finished they may terminate the transaction by pressing the white “Card Return” button. The display will read “Wait”
for a few seconds. The card’s magnetic stripe will be encoded with any unused value and the card will be returned
to the exit position. The Display will read “Take Card” and the copier will be disabled.
CAUTION: It is very important not to interrupt the power source or to remove the copy card without firstCAUTION: It is very important not to interrupt the power source or to remove the copy card without first
pressing the white “Card Return” button. If either of these actions is attempted, the card will not be encodedpressing the white “Card Return” button. If either of these actions is attempted, the card will not be encoded
with any unused value and the card will no longer be useable.with any unused value and the card will no longer be useable.

4
BYPASS OPERATIONBYPASS OPERATION
Your JamexJamex model 7110/7112 Stand Alone Card Reader has a Bypass feature and has been shipped with a
Bypass Card to allow authorized personnel to make copies with no cost to themselves. To use the Bypass feature,
simply insert the blue Bypass Card into the reader, arrow first and face up. The display will read -BYPASS-. As
long as the card is in place copies may be made. When the user is finished they may press the white Card Return
button and reclaim the Bypass Card.
EXTENDED FEATURES OF THE MODEL 7112EXTENDED FEATURES OF THE MODEL 7112
Set Card Value CARDSSet Card Value CARDS
The Model 7112 has the capability of programming value to Stored Value Cards. This can be done with a Set Card
Value card, which is supplied with the 7112 Card Reader. For instructions on how to use a Set Card Value Card,
see page 8, Program Value to Cards section of this manual.
DUAL PRICINGDUAL PRICING
This feature allows for an alternate price to be charged for a different size of paper. This feature is dependent upon
the make and model copier being interfaced with the Model 7112.
WARNING: JAMEX COPY CARDS SHOULD NOT HAVE HOLES PUNCHED IN THE CARD. STICKERS ORWARNING: JAMEX COPY CARDS SHOULD NOT HAVE HOLES PUNCHED IN THE CARD. STICKERS OR
OTHER FOREIGN MATERIALS PLACED ON THE CARDS WILL ENDANGER THE OPERATION OF THEOTHER FOREIGN MATERIALS PLACED ON THE CARDS WILL ENDANGER THE OPERATION OF THE
READER. DO NO BEND THE CARD OR WRITE ON THE CARD SURFACE.READER. DO NO BEND THE CARD OR WRITE ON THE CARD SURFACE.

5
DATA MANAGEMENTDATA MANAGEMENT
READING THE METERSREADING THE METERS
The Jamex Vending SystemJamex Vending System 7110/7112 allows you to account for the use of the vended equipment by reading and
recording amounts shown on the display. To read the meters, insert the blue Read Meters card arrow first and face
up. The display will show “Meters..” for an instant and will return the card to the exit position. Leave the card in this
position as you record the information from the meters. The following chart explains the information which will flash
on the display. After you read and record each line, press the white button once to advance the display to the next
meter.
DISPLAYDISPLAY EXPLANATIONEXPLANATION
Meter A 1-----NUMBER The number of copies made using cards with site code 1
Meter A 2----NUMBER These meters will track copies made if there are site codes 2, 3, and
Meter A 3----NUMBER 4 to track different types of card users
Meter A 4----NUMBER
NOTENOTE: Meter B tracks the alternate priced copies made. This dual price capability is an extended feature of the Model 7112 and
is dependent on the copier to which it is being interfaced.
Meter B 1----NUMBER The number of alternate priced copies made using cards with site code 1
Meter B 2----NUMBER These meters will track alternate priced copies made, if there are site codes 2,3,
Meter B 3--------NUMBER and 4 to track different types of card users
Meter B 4----NUMBER
Bypass A 1----NUMBER The number of copies made that would have been charged to cards with
site code 1 except that they were made using a Bypass card.
Bypass A 2----NUMBER If there are additional site codes, the number of copies that would have
Bypass A 3----NUMBER been charged to cards with each site code but were made using a
Bypass A 4----NUMBER Bypass card will be displayed
NOTE:NOTE: Meter B tracks the alternate priced copies made. This dual price capability is an extended feature of the Model 7112 and
is dependent on the copier to which it is being interfaced.
Bypass B 1----NUMBER The number of alternate price copies made that would have been charged to
cards with site code 1 except that they were made using a Bypass card.
Bypass B 2----NUMBER If there are additional site codes, the number of alternate priced copies that Bypass
B 3----NUMBER would have been charged to cards with each site code but were made using a
Bypass B 4----NUMBER Bypass card will be displayed
Sales 1----$ VALUE The total dollar value of copies made using cards with site
code 1.
Sales 2----$ VALUE If there additional site codes, the total value of copies made
Sales 3----$ VALUE for each site code will be displayed.
Sales 4----$ VALUE
TotalCyc----NUMBER Total number times a card has been inserted and read.
ReadFail----NUMBER Total number of times a card was inserted and could not be
read.
This completes the meter readings. Remove the Read Meters card and the display will return to “Insert Your Card”.

6
INSTALLATION AND SET UPINSTALLATION AND SET UP
UNPACKING THE VENDING SYSTEMUNPACKING THE VENDING SYSTEM
The following equipment is included in your model 7110/7112 shipment:
- Model 7110/7112 vending unit, including cabling appropriate to the copy machine specified
on your purchase order and a power cable
- This Operation Manual & Installation and Service Guide
-Management Card Set - Read Meters Card, Set Prices Card, Bypass Card
The Model 7112 will also include Command Cash Card
PHYSICAL MOUNTINGPHYSICAL MOUNTING
Your Jamex Vending SystemJamex Vending System may be simply placed near the copier it will control or it may be bolted to a cabinet or
a table via the pre drilled mounting holes in the base of the unit.
ELECTRICAL INSTALLATIONELECTRICAL INSTALLATION
Please refer to the Point-to-Point Wiring Diagram and Step by Step Electrical Connection directions on the last two
pages of this manual.
PROGRAMMING YOUR JAMEX MODEL 7110/7112PROGRAMMING YOUR JAMEX MODEL 7110/7112
ADJUSTING THE PRICE PER COPYADJUSTING THE PRICE PER COPY
The blue Set Prices card allows you to adjust the prices charged for each site code that is programmed into your
Stand Alone Card Reader. This card also allows you to change the maximum value which may be read on any
card. The maximum card value is a safety function to limit the loss by any patron who may lose a card. Follow the
steps below to adjust Max Card Value and Prices.
Begin the process of setting prices by inserting the Set Prices card.
-the display will show “Prices..” for an instant and will return the card to the exit position.
-the display will begin flashing Max Card....ƒ025.000 (NOTE UP ARROW)
To increase the maximum value that may be read from a card press the white button on the front of the reader.
-the display will show an increased max card value of $.001 cent for each time the white button is
pressed.
If you press and hold the white button, the amount will continue to increase until you release the button.