janitza JPC 100-PRO Instruction manual

Doc. no. 2.100.116.1.b 08/2022
Smart Energy Panel
JPC 100-PRO
User manual and technical data
Janitza electronics GmbH
Vor dem Polstück 6
35633 Lahnau | Germany
Support [phone]
[email protected] | www.janitza.com
www.janitza.com

JPC 100-PRO www.janitza.com
2
JPC 100-PRO
Smart Energy Panel
Doc. no. 2.100.116.1.b
08/2022
The German version is the original version of the documentation.

www.janitza.com JPC 100-PRO
3
Subject to technical alterations.
The contents of our documentation have been compiled with great care and reflect the cur-
rent state of the information available to us. Nonetheless, we wish to point out that updates of
this document are not always possible at the same time as technical refinements are imple-
mented in our products. Information and specifications are subject to change at any time.
Please check for the latest version.

JPC 100-PRO www.janitza.com
4
Table of contents
1. Information on the device and the user manual 5
1. 1 Disclaimer 5
1. 2 Copyright notice 5
1. 3 Technical changes 5
1. 4 About this user manual 5
1. 5 Defective device/disposal 6
1. 6 Conformity declaration 6
2. Safety 7
2. 1 Display of warning notices and safety information 7
2. 2 Hazard levels 7
2. 3 Product safety 7
2. 4 Hazards when handling the device in the switchboard cabinet 9
2. 5 Electrically qualified personnel 9
3. Product description 10
3. 1 Scope of performance 10
3. 2 Incoming goods inspection 10
3. 3 Intended use 10
3. 4 Scope of delivery 11
3. 5 Operating concept 11
3. 6 Connections and rating plate 12
3. 6. 1 Connections 12
3. 6. 2 Rating plate 12
4. Mounting 13
4. 1 Installation location 13
4. 2 Mounting orientation 13
4. 3 Securing 14
5. Installation 15
5. 1 Circuit breaker 15
5. 2 Supply voltage 15
5. 3 Connection of the measurement devices 15
6. Initial commissioning and user interface 16
7. Service and maintenance 17
7. 1 Repair 17
7. 2 Service 17
7. 3 Update 17
8. Technical data 18

www.janitza.com JPC 100-PRO
5
1. Information on the device and the user manual
1. 1 Disclaimer
Compliance with the usage information for
the devices is a prerequisite for safe oper-
ation and attaining the stated performance
characteristics and product features.
Janitza electronics GmbH assumes no
liability for bodily injury, material damage or
financial losses which result from disregard of
the usage information.
Make sure that your usage information is
readily available and legible.
1. 2 Copyright notice
© 2022 - Janitza electronics GmbH - Lahnau.
All rights reserved.
Any reproduction, processing, distribution or
other use, in whole or in part, is prohibited.
All trademarks and the rights arising from
them are the property of the respective own-
ers of these rights.
1. 3 Technical changes
• Make sure that your device matches the
user manual.
• This user manual applies to the JPC 100-
PRO. Separate validities and distinctions
are marked.
• First make sure you have read and under-
stood the usage information accompany-
ing the product.
• Keep the usage information associated
with the product available for the entire
service life and pass it on to any possible
subsequent users.
• Find out about device revisions and the
associated modifications of the usage
information associated with your product.
1. 4 About this user manual
If you have questions, suggestions or ideas
for improvement of the user manual, please
let us know via email at:
[email protected].
INFORMATION
This user manual describes the JPC 100-PRO
and provides information on how to operate
the device. Separate validities and distinctions
of the device are marked.
In addition to this user manual, refer to the
further usage information for your device.
INFORMATION
Our usage information uses the grammatical
masculine form in a gender-neutral sense! This
form always refers equally to women, men and
diverse. In order to make the texts more read-
able, distinctions are not made. We ask for
your understanding for these simplifications.

JPC 100-PRO www.janitza.com
6
1. 5 Defective device/disposal
Before sending defective devices, modules
or components back to the manufacturer for
testing:
• Contact the manufacturer's Support de-
partment.
• Send devices, modules or components
complete with all accessories.
• When doing so, please bear the terms for
transportation in mind.
INFORMATION
Please return defective or damaged devices to
Janitza electronics GmbH in accordance with
the shipping instructions for air or road freight
(complete with accessories).
Observe special regulations for devices with
built-in batteries or rechargeable batteries!
Do not attempt to open or repair the device
(the component) on your own because other-
wise all warranty claims become invalid!
Please observe national regulations for the
disposal of the device! Dispose of individual
parts as needed depending on their compo-
sition and existing country-specific regula-
tions, for example, as:
• Electronic waste,
• Batteries and rechargeable batteries.
• Plastics.
• Metals.
Engage a certified disposal company to han-
dle scrapping as needed.
1. 6 Conformity declaration
The laws, standards and directives applied
by Janitza electronics GmbH for the device
can be found in the Declaration of Conformity
on our website www.janitza.com.

www.janitza.com JPC 100-PRO
7
2. Safety
The chapter on Safety contains information
which must be observed to ensure your per-
sonal safety and avoid material damage.
2. 1 Display of warning notices and
safety information
The warning notices shown below
• are found throughout all of the documen-
tation,
• can be found on the devices themselves.
• indicate potential risks and hazards,
• underscore aspects of the information
provided that clarifies or simplifies proce-
dures.
The additional symbol onthedevice itself
indicates anelectrical danger that can result
in serious injuries or death.
This general warning symbol draws atten-
tion to a possible risk of injury. Be certain to
observe all of the information listed under this
symbol in order to avoid possible injury or
even death.
2. 2 Hazard levels
Warning and safety information is marked by
a warning symbol, and the hazard levels are
shown as follows, depending on the degree
of hazard:
DANGER
Warns of an imminent danger which, if not
avoided, results in serious or fatal injury.
WARNING
Warns of a potentially hazardous situation
which, if not avoided, could result in serious
injury or death.
CAUTION
Warns of an immediately hazardous situation
which, if not avoided, can result in minor or
moderate injury.
ATTENTION
Warns of an immediately hazardous situation
which, if not avoided, can result in material or
environmental damage.
INFORMATION
Indicates procedures in which there is no haz-
ard of personal injury or material damage.
2. 3 Product safety
The device reflects current engineering
practice and accepted safety standards, but
hazards can arise nonetheless.
Observe the safety regulations and warning
notices. If notices are disregarded, this can
lead to personal injury and/or damage to the
product.

JPC 100-PRO www.janitza.com
8
WARNING
Risk of injury due to electrical voltage!
Severe bodily injury or death can result!
Therefore please abide by the following:
• Switch off your installation before
commencing work! Secure it against
being switched on! Check to be sure
it is de-energized! Ground and short
circuit! Cover or block off adjacent live
parts!
• During operation and troubleshooting
(especially for DIN rail devices), check
your systems for dangerous voltages
and switch these off if necessary!
• Wear protective clothing and protec-
tive equipment in accordance with
applicable guidelines when working on
electrical systems!
• Do not touching bare or stripped leads
that are energized! Equip stranded
conductors with wire ferrules!
• Only connect screw terminals with the
same number of poles and the same
type!
• Hazardous voltages can be present in
all circuitry parts that are connected to
the power supply!
• There can still be hazardous voltages
present in the device even after it has
been disconnected from the supply
voltage!
• Protect wires, cables and devices with
a suitable line circuit breaker/fuse!
• Never switch off, remove or tamper
with safety devices!
• Do not exceed the limit values speci-
fied in the user manual and on the rat-
ing plate! This must also be observed
during testing and commissioning!
• Take note of the safety and warning
notices in the documents that belong
to the device!
Any unauthorized tampering with or use of
the device,
• which goes beyond the mechanical,
electrical or other operating limits can lead
to personal injury and/or damage to the
product.
• constitutes “misuse” and/or “negligence”
under the product’s warranty and thus
voids the warranty for any possible result-
ing damage. In this regard, please take
note of section “3. 3 Intended use” on
page 10.
Read and understand the user manual and,
if applicable, the usage information before
installing, operating, maintaining and using
the device.
Only operate the device when in perfect
condition and in compliance with this user
manual and the usage information that is
included. Send defective devices back to
the manufacturer in compliance with proper
transport conditions. Retain the user manual
throughout the service life of the device and
keep it at hand for consultation.
When using the device, also observe the
legal and safety regulations for your system
that are applicable for the respective use
case.

www.janitza.com JPC 100-PRO
9
2. 4 Hazards when handling the device
in the switchboard cabinet
When operating electric devices, it is un-
avoidable for certain parts of these devices
to conduct hazardous voltage. Consequently,
severe bodily injury or material damage can
occur if they are not handled properly.
Therefore, when handling our devices, always
observe the following:
• do not exceed the limit values specified in
the user manual and on the rating plate!
This must also be observed during testing
and commissioning!
• Take note of the safety and warning notic-
es in all usage information that belongs to
the device!
2. 5 Electrically qualified personnel
To avoid bodily injury and material dam-
age, only electrically qualified personnel are
permitted to work on the devices and their
components, modules, assemblies, systems
and current circuits who have knowledge of:
• The national and international accident
prevention regulations.
• Safety technology standards.
• Installation, commissioning, operation,
disconnection, grounding and marking of
electrical equipment.
• The requirements concerning personal
protective equipment.
Electrically qualified persons within the scope
of the technical safety information of all
usage information associated with the device
and its components are persons who can
furnish proof of qualification as an electrically
skilled person.
WARNING
Warning against unauthorized manipula-
tion or improper use of the device or its
components!
Opening, dismantling or unauthorized ma-
nipulation of the device and its components
which goes beyond the mechanical, elec-
trical or other operating limits indicated can
lead to material damage or injury, up to and
including death.
• Only electrically qualified personnel
are permitted to work on the devices
and their components, assemblies,
systems and current circuits.
• Always use your device or component
only in the manner described in the
associated documentation.
• If there is discernible damage, send
the device or the component back to
the manufacturer!

JPC 100-PRO www.janitza.com
10
3. Product description
3. 1 Scope of performance
This device is part of a customer-specific
complete solution. It serves as a user inter-
face and operator interface for the measure-
ment devices used.
The device is intended for:
• Visualization of current and voltage mea-
suring devices in bus systems.
• Measured value monitoring and configu-
ration of connected Janitza measurement
devices.
For more information on the complete solu-
tion, please refer to the corresponding usage
information.
3. 2 Incoming goods inspection
Safe and trouble-free operation of this device
presupposes proper transport, storage, set-
up and assembly as well as operation and
maintenance in addition to compliance with
the safety information and warning notices.
Exercise due caution when unpacking and
packing the device, do not use force and only
use suitable tools.
Before installing the device check the follow-
ing:
• Its flawless mechanical condition by visual
inspection.
• The scope of delivery for completeness.
If it can be assumed that safe operation is no
longer possible:
• Disconnect the device from operation
immediately!
• Secure the device against being switched
on again!
It can be assumed that safe operation is no
longer possible if the device, for example
• Has visible damage.
• No longer functions despite an intact pow-
er supply.
• Was subjected to extended periods of
unfavorable conditions (e.g. storage out-
side of the permissible climate conditions
without adaptation to the room climate,
condensation, etc.) or transport stress
(e.g. falling from an elevated position, even
without visible external damage, etc.).
3. 3 Intended use
The device is:
• Intended for installation in switchboard
cabinets.
• Not intended for installation in vehicles!
Use of the device in non-stationary equip-
ment constitutes an exceptional environ-
mental condition and is only permissible
by special agreement.
• Not intended for installation in environ-
ments with harmful oils, acids, gases,
vapors, dusts, radiation, etc.
Safe and trouble-free operation of the device
requires proper transport, storage, assembly,
installation, operation and maintenance.