Jaypro Sports VBWR-1 User manual

Rev-A Page 1of 6
-- VOLLEYBALL WALL MOUNT, VBWR-1 --
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com

Rev-A Page 2of 6
VOLLEYBALL WALL MOUNT, VBWR-1
PARTS LIST (QTY: SINGLE UNIT)
ITEM
IMAGE
DESCRIPTION
QTY
1
VOLLEYBALL WALL RACK
P/N: VBWR-101
1
2
VELCRO STRAPS
P/N: VBWR-102
3
3
VINYL EDGE TRIM
P/N: RP5064
2
4
FIBERGLASS SPACER
P/N: VBWR-104
6
5
1/4"-20 x 4”HEX HEAD CAP SCREW
P/N: HS5373
6
6
1/4"-20 NYLON LOCK NUT
P/N: HN256
6
7
1/4" FLAT WASHER
P/N: HW2093
12
ITEM
IMAGE
DESCRIPTION
QTY

Rev-A Page 3of 6
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) NEVER ALLOW ANYONE TO CLIMB OR HANG ON THE NET OR GOAL
FRAME. AS SERIOUS INJURY OR DAMAGE TO THE EQUIPMENT MAY
OCCUR.
3) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
4) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
Tools Require:
1
Hammer
1
Tape Measure
1
Drill
1
Masonry Bit
1
Ladder
1
Socket Wench
oUnpack all parts and check against parts list to ensure that all have been
included.
oInspect all parts for damage. Report any damages to the trucking
company.
oTools required: tape measure, step ladder
3/8” LAG HEX CAP SCREWS
3/8” LONG LAG SCREW ANCHOR
N o t I n c l u d e d

Rev-A Page 4of 6
INSTALLATION AND USE CONSIDERATIONS
1) Do not locate wall storage rack in or adjacent to heavy traffic areas. The stored
volleyball uprights and/or the rack may pose a hazard to those in the vicinity.
2) The straps provided with this unit when properly used, will safely hold an upright
which weighs 85 pounds or less. Do not exceed this working limit.
Installation Instructions:
1) Installation requirements vary with the type of wall onto which the rack is being
installed. Additional hardware may be required depending on the type of wall.
General recommendations are listed below. The rack can be installed horizontally,
vertically or even diagonally. Vertical installation works best for holding hoops,
while horizontal or diagonal works better for jump ropes.
Installation onto Concrete or Brick:
2) With the rack in the desired position, mark the center of the two holes at the end
of the rack on the wall. Using a masonry bit the same size as the expansion
sleeves drill holes the same depth as the expansion sleeves. Insert the expansion
sleeves into the holes. Align the rack over the expansions sleeves and install the
hex cap screws.
Installation onto Wood Wall or Solid Wall:
Note: Not concrete or Wallboard / Gypsum or Drywall.
3) With the rack in the desired position, mark the center of the two holes at the end
of the rack on the wall. Drill two wall pilot holes (about 1/8” in diameter). Align
the rack over the expansions sleeves and install the hex cap screws.
Installation onto Drywall:
Note: Also called Gypsum or Wallboard (drywall anchors not included).
4) Drywall alone will not be strong enough to screws the cap screws directly into
and the expansions sleeves are not suitable for use in drywall. There are couples
of recommended options. The first is to use drywall anchors screws and washers.
These types of anchors are readily available in your local home center or
hardware store. Use the metal inserts and the large size available to provide the
maximum weight support. Washers will also likely be required to keep the head
of the screws from slipping through the hole in rack. The second options would be
to securely attach a large 1” thick piece of wood or plywood to your wall that is
larger than the rack and then install the rack to that piece of wood.

Rev-A Page 5of 6
ASSEMBLY INSTRUCTIONS
1) Affix two rubber strips to each wall rack cradle. These will help to protect the
finish on your standards.
2) The wall rack should be securely anchored to the wall using a suitable anchor
chosen for the type of wall being mounted to, whether CMU block, poured
concrete or studded. If attaching to a studded wall ensure that the anchors are
attached directly to the studs. See page 4 of 5 for additional information.
3) Locate the general area where the wall rack (1) is to be mounted. Drill three
appropriately sized pilot holes approximately 4 ½’ (54”) above floor level and at
16” / 8” on center from each other.
4 ½’ (54”) Off Floor
Center of Bracket

Rev-A Page 6of 6
4) When storing the upright in the wall rack, a minimum of two trained adults should
carry the unit. Be sure the upright stands vertical with no lean. Strap the upright
into the cradle by wrapping the velcro straps (2) around as tight as possible.
FIBERGLASS SPACER
VELCRO STRAPS
1/4"-20 x 4” HEX HEAD CAP, SCREW
1/4"-20 NYLON LOCK NUT
1/4" FLAT WASHER