peerless-AV DS-LEDVST Series User manual

12022-01-13 #:146-9069-1
DS-LEDVST Series
*Actual conguration may vary
ENG

22022-01-13 #:146-9069-1
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
#
Skip to step.
ENG
Wear anti-static gloves.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.

walls. Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

call customer care at 1-800-865-2112.
WARNING
x3
Screws must get at
least three full turns

ENG
5mm

32022-01-13 #:146-9069-1
Parts List
Description
Acolumn
Bhorizontal extrusion
Cvertical spacer
Dhorizontal spacer
E3mm allen wrench two-tip T-handle
Fwall plate shim
Gconnector plate
HM5 x 5mm set screw
IM5 x 8mm socket screw
J#14 x 1.75" wood screw
K2.5mm allen wrench
LM5 x 40mm screw
MM8 x 12mm screw
A
column B
horizontal extrusion
Parts (Before beginning, make sure you have all parts shown below).
Refer to parts list included with your model.
ENG
C
vertical
spacer
H
M5 x 5mm
set screw
D
horizontal
spacer
G
connector
plate
I
M5 x 8mm
F
wall plate
shim
E
3mm allen wrench
two-tip T-handle
J
#14 x 1.75" wood screw
K
2.5mm allen wrench
L
M5 x 40mm
M
M8 x 12mm screw

42022-01-13 #:146-9069-1
1-1
Optional: If connecting two top horizontal extrusions,

ENG
B
B
1-2
Use extrusion connectors to connect top horizontal extrusions.
ENG
G (4) H (8)
E
B
B
1-3
Replace one hook-on bracket in between connected extrusions and tighten hardware.
ENG E
B
B
K
L
Remove and save hardware.
ENG
Use saved hardware.
ENG

52022-01-13 #:146-9069-1
1-4
E
Secure additional hook-on brackets for top horizontal extrusions.
ENG
L
L
B
B

62022-01-13 #:146-9069-1
2-1
Optional: If connecting two bottom horizontal extrusions,

ENG
2-2
Use extrusion connectors to connect bottom horizontal extrusions.
ENG
H (8)
G (4)
B
B
K
B
B
E
Remove and save hardware.
ENG

72022-01-13 #:146-9069-1
2-3
Replace one hook-on bracket in between connected extrusions.
ENG
B
B
E
Use saved hardware.
ENG

82022-01-13 #:146-9069-1
3
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
3-1
ENG When installing more than one display to a wood stud wall reinforced with plywood (minimum Grade BC, 1/2"
thick) that may be covered in gypsum board (drywall) up to 5/8" thick, the mounting surface must be plumb
(+/- .25”) across the height of the video wall and straight (+/- .25”) across the width of the video wall.

92022-01-13 #:146-9069-1
3-2
Use a laser level to keep mounting holes
level.
ENG
2.0"
(51mm)
display tile
7/8" (22mm) minimum
for mounting clearance

10 2022-01-13 #:146-9069-1
3-3
Level top horizontal extrusion and mark
mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick).
ENG
B

11 2022-01-13 #:146-9069-1
3-5
Level extrusion. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
3-4
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)
B
J

12 2022-01-13 #:146-9069-1
3-6

horizontal extrusion.
ENG
3/8"
(10mm)

ENG
J
C
C
B
J
1.34"
(34mm)

13 2022-01-13 #:146-9069-1
3-7
Use third vertical spacer to align bottom

then mark mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick).
ENG
B
C

ENG
C
B
1.34"
(34mm)

14 2022-01-13 #:146-9069-1
B
3-9
Use third vertical spacer to align bottom

spacer, then install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
J
3-8
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)

15 2022-01-13 #:146-9069-1
4
Remove vertical spacers.
ENG
3/8"
(10mm)
C

16 2022-01-13 #:146-9069-1
Hook on and secure all columns.
ENG
A
E
Tighten hardware.
ENG
I
5-1

17 2022-01-13 #:146-9069-1
5-2
E
Remove brackets from outer columns only.
ENG

18 2022-01-13 #:146-9069-1
6-1
Loosen hardware on columns.
ENG E

19 2022-01-13 #:146-9069-1
6-2
Plumb and level outer columns, then tighten hardware.
Tighten hardware on four corner wall plates.
ENG
Tighten.
ENG
Tighten.
ENG
E

20 2022-01-13 #:146-9069-1
6-3
Tie a string between top slots on outer
columns in order to level the depth of each.
ENG
Loosen, adjust, tighten.
ENG
E
Tighten.
ENG
Loosen.
ENG
Optional leveling for bowed walls
ENG
Insert.
ENG
F