Jaypro Sports Series FHG-2AL User manual

Rev-A Page 1of 8
-- FHG-2AL --
(Formally: OFHG-7124)
OFFICIAL FIELD HOCKEY GOAL
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com

Rev-A Page 2of 8
PARTS LIST (QTY: SINGLE UNIT)
ITEM
IMAGE
DESCRIPTION
QTY
1
TOP FRONT CROSSBAR
P/N: FHG-2AL-1XB
1
2
RIGHT SIDE FRAME
P/N: FHG-2AL-1R
1
3
LEFT SIDE FRAME
P/N: FHG-2AL-1L
1
4
BOTTOM REAR CROSSBAR
P/N: FHG-1XB-1
2
5
TOP REAR CROSSBAR
1
6
REAR FOOT BOARD x 48 1/8" LONG
P/N: FHG-16-1
3
7
SIDE FOOT BOARD x 45 3/4" LONG
P/N: FHG-16-2
2
8
5/16"-18 x 2 1/2" BUTTON HEAD SCREW
P/N: HS5180
40
9
5/16" FLAT WASHER
P/N: HW5020
80
10
5/16-18 NYLON LOCK NUT
P/N: HN261
40
11
3/8”-16 x 2-1/2” LONG HEX BOLT
P/N: HS291
2
12
3/8” LOCK WASHER
P/N: HW334
2
13
3/8” FLAT WASHER
P/N: HW2047
2
14
NET CLIP KIT
P/N: SNT-180
1
15
7' x 12' x 4' WEATHERPROOF NET
P/N: FHND-8
1
16
2" SQUARE TUBE CAP
P/N: EP0018
2
17
1 1/2" SQUARE TUBE CAP
P/N: EP0034
2
18
Optional Wheel Kit
P/N: FHK-1WK
N/A

Rev-A Page 3of 8
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) NEVER ALLOW ANYONE TO CLIMB OR HANG ON THE NET OR GOAL
FRAME. AS SERIOUS INJURY OR DAMAGE TO THE EQUIPMENT MAY
OCCUR.
3) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
4) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY.
5) FOR REPAIR OR REPLACEMENT PARTS, CONTACT YOUR DEALER OR
JAYPRO SPORTS.
Tools Require:
1
Rubber Mallet
1
1/2" Socket Wrench or Box Wrench
1
3/16" Allen Wrench
oUnpack all parts and hardware, and check against the parts list
to ensure that all items have been included.
oInspect all parts for damage. Report any damages to the
trucking company immediately.

Rev-A Page 4of 8
ASSEMBLY (REQUIRES 2 PEOPLE):
1) Lay parts out on clean dry flat surface. NOTE: There is a left and right side frame,
distinguished by the offset to accommodate the Foot Boards. Identify each frame
and install keeping the offset to the outside of the goal.
2) Assemble both side frames onto the Top Crossbar, as shown in Figure 1.
Figure 1
3) Insert the End Caps into the bottom of the frame.
4) Install the Top & Bottom Crossbars as shown in Figure 2. Loosely install all
hardware. Make sure the goal is square and the top fully inserted and then
tighten all hardware.
2” SQUARE TUBE CAP
TOP FRONT CROSSBAR
RIGHT SIDE FRAME
LEFT SIDE FRAME
1-1/2” SQUARE TUBE
CAP

Rev-A Page 5of 8
Figure 2a
5/16”-18 x 2 1/2”
BUTTON HEAD SCREW
5/16” WASHER
5/16” NYLON LOCK NUT
5/16” WASHER
5/16”-18 x 2 1/2”
BUTTON HEAD SCREW
5/16” NYLON LOCK NUT
BOTTOM CROSSBARS
NOTE: LARGE HOLE FOR WHEEL KIT

Rev-A Page 6of 8
Figure 2b
(Flip 180°)
3/8” LOCK WASHER
3/8” FLAT WASHER
TOP REAR CROSSBAR
3/8”-16x 2-1/2” HEX BOLT
Be careful not to cross-thread the nut or bolt when installing the top rear crossbar.
Lay goal on its back and place a 2” x 4” block underneath far end of the crossbar.
Note:

Rev-A Page 7of 8
7) Stand the goal up and install the Foot Boards. Install the Rear Boards first.
8) Drape the net over the goal and secure net to the goal using the net clips & screws.
Note the top corner of net has a label.
9) To minimize the amount of sag across the back of the net, tie off the cord that passes
across the back corner of the net to the backstays.
5/16”-18 x 2 1/2”
BUTTON HEAD SCREW
5/16” WASHER
5/16” NYLON LOCK NUT
SIDE FOOT BOARD
SIDE FOOT BOARD
REAR FOOT BOARD
5/16” WASHER

Rev-A Page 8of 8
SNT-180
Net Clip Kit Bag Contains 82 Pieces
Note: Tighten the screw stud snugly,
but do not overtighten it. This may
strip the treads in the snug plug.
TOP CROSSBAR / UPRIGHT
#8 x 3/4” SCREW
P/N: HS5031
NET TIE CLIP
P/N: HM5076
5/16” SNAP PLUG
P/N: RP5010