Jazz SOUND PLATFORM SP2.1 User manual

SOUND PLATFORM SP2.1
Includes
1 - Stereo Sound Platform
1 - IR Remote Control
1 - Lithium Battery (3V, CR2025)
1 - Stereo RCA Patch Cable
1 - Digital Optical Patch Cable
1 - AC Power Cord
Features
• Simulated surround sound from a single, space-saving cabinet
• Enjoy deep, enveloping bass without bulky speakers or amps
• Includes advanced Digital Signal Processing (DSP)
• Use with flat-panels TVs and digital music players
• Syncs to almost any Bluetooth audio device
Amplifier Specs:
Bi-amp design; independent amp channels for each woofer and each set of
midrange drivers and tweeter
20W Continuous x 4 Channels into 40 for 80 Watts Total Amplification 35Hz -
20kHz; <1% THD
Audio Inputs:
1 - Digital Coaxial Audio Input
1 - Digital Optical Audio Input
1 - Stereo Analog Line Level Audio Input 1
Bluetooth Input
Speaker Configuration:
- Stereo - Four Front-facing 2-1/2” Midrange Drivers
- Two 1” Silk Dome Tweeters
- Two Down-firing 5-1/4” Subwoofers - Ported Enclosure
IR Remote Control
• ON/Standby
• Volume & Mute
• Discrete Input Select
• Treble & Bass Adjustment
• Simulated Surround Sound (Toggle On/Off)

Congratulations and thank you for purchasing the JAZZ AUDIO SOUND PLATFORM Table-Top Surround Sound
System. The JAZZ AUDIO SOUND PLATFORM greatly enhances the sound quality of today’s flat screen LED, LCD
and Plasma TVs without having to add a lot of speakers. A single speaker system that requires very little space, the
SOUND PLATFORM can be installed below or in front of a high definition TV or inside a cabinet. You’ll enjoy simulated
surround sound from a single, space- saving cabinet with deep, enveloping bass without bulky speakers or amps. The
JAZZ AUDIO SOUND PLATFORM easily connects to inputs on today’s flat panel TVs and digital music players and
even syncs to almost any Bluetooth audio device.
JAZZ AUDIO
SOUND PLATFORM
FRONT PANEL
1. STATUS LED - (Behind front panel lens.) One multi-color LED. This LED will illuminate red/blue and flash in
different modes to indicate changes in the SOUND PLATFORM operational status. SOLID RED - OFF (Standby).
Power cord is connected and AC switch is turned ON, but the SOUND PLATFORM is OFF.
SOLID BLUE – ON – JAZZ AUDIO SOUND PLATFORM is ON.
SINGLE BLUE FLASH - Confirms receiving an IR command from the JAZZ AUDIO SOUND PLATFORM
Remote for changes to Treble/Bass, EQ Reset, Simulated Surround (SR), single Volume UP/DOWN
command, initiating output of the Bluetooth Connection Code.
RAPID BLUE FLASH - Confirms receiving a continuous IR stream from the SOUND PLATFORM
Remote for ramping volume UP/DOWN. Rapid blue flash also indicates the SOUND PLATFORM is in
Bluetooth pairing mode.
SLOW BLUE FLASH - Audio Mute. Audio signal to the speakers is turned OFF.
TWO BLUE FLASHES; DELAY - Bluetooth input is selected and no Bluetooth device is connected or it is
out of range.
2. IR SENSOR - (Behind front panel lens.) The IR Sensor ‘sees’ the IR control commands output from the
SOUND PLATFORM IR Remote Control when buttons are pressed on the remote for armchair control of the
SOUND PLATFORM. This sensor must be unobstructed for direct line-of-sight to the remote, or the remote will
not be able to control the SOUND PLATFORM.
Back Panel Connection Plate
JAZZ AUDIO
SOUND PLATFORM
REAR PANEL
3. FRONT AND REAR PANEL BASS PORTS -Two pairs of tuned openings in the SOUND PLATFORM cabinet
allow air to ‘release’ from the cabinet and enhance low frequency audio. Allow at least 3 inches of clearance to a
back wall to allow air to move freely from the ports for full bass extension.
33

4. DIGITAL COAXIAL INPUT - One RCA
jack. Connect to the Digital Coaxial OUT on a
TV or other source. This input is selected by
pressing the COAX button on the SOUND
PLATFORM IR Remote. NOTE: The audio
output of a TV, Blu-ray Disc player, game
console, or DVD player connected to the
SOUND PLATFORM via Coaxial Digital must
be set to PCM in the source’s setup. Please
see the device’s Owner’s Manual for details.
5. DIGITAL OPTICAL INPUT - One TOSLINK® connector. Connect to the Digital Optical OUT on a TV or other
source. This input is selected by pressing the OPT button on the SOUND PLATFORM IR Remote.
NOTE: The audio output of a TV, Blu-ray Disc player, game console, or DVD player connected to the SOUND
PLATFORM via Optical Digital, must be set to PCM in the source’s setup. Please see the device’s Owner’s Manual
for details.
6. AUDIO INPUT - Two RCA jacks. Connect to the L & R Line Level Audio OUT on a TV or other source. This input
is selected by pressing the AUX button on the JAZZ AUDIO SOUNF PLATFORM IR Remote.
7. POWER - Turns the power to the JAZZ AUDIO SOUND PLATFORM ON/OFF. Always turn the power OFF when
making connections to the SOUND PLATFORM. The Front Panel LED will illuminate red to indicate Standby (power
switch ON, SOUND PLATFORM turned OFF with IR Remote) or blue to indicate that the SOUND PLATFORM is ON.
8. AC INPUT- Universal power connector. Automatically selects AC voltage for a given region. Connect to the
included 2-conductor AC Power Cord. After all audio connections have been made and confirmed, plug the power
cord into an un-switched AC Outlet to power the SOUND PLATFORM.
9. DOWN FIRING SUBWOOFERS - The SOUND SPLATFORM bottom panel features two 5-1/4” subwoofers, one
for left channel bass and one for right channel bass. When handling the SOUND PLATFORM, be careful not to
grab or hold the cabinet bottom where the woofers are located to prevent damaging the woofers. Also take care to
not set the cabinet down on anything but a flat surface clear of obstructions.
When placing the SOUND PLATFORM
on a shelf or stand, be sure there are no
objects under the cabinet that will
damage or block the woofers and check
to make sure there are no objects on the
sides of the cabinet that will block the
space under the SOUND PLATFORM.
Blocking this space will reduce overall
bass performance.

JAZZ AUDIO SOUND PLATFORM IR REMOTE CONTROL
1. POWER - Press this button to turn the SOUND PLATFORM ON/OFF.
2. INPUT - Press to select a connected source. The SOUND PLATFORM Front Panel Status LED will flash once to
indicate a change in input selection.
COAX - Press to select the Digital Coaxial Input.
OPT - Press to select the Digital Optical Input.
AUX - Press to select the L&R Line Level Audio Input
Press to select a paired Bluetooth device. A Bluetooth device must be paired to the JAZZ AUDIO SOUND PLATFORM
for audio output. A paired Bluetooth device will remain ‘connected’ after changing inputs as long as the Bluetooth device
has not moved out of range, turned off or otherwise disconnected.
3. Press this button to initiate Bluetooth pairing mode. The Front Panel Status LED will rapid flash blue. The
SOUND PLATFORM will output a pairing code that will be picked up by any active Bluetooth device that is within range
of the SOUND PLATFORM.
4. VOLUME -/+ Press VOL - to reduce volume. Press VOL + to increase volume.
5. MUTE - Press this button once to mute the SOUND PLATFORM. Press again to un-mute the SOUND PLATFORM.
6. SURR - Press this button to activate the simulated surround audio mode. Press again to turn Surround Mode OFF.
7. EQ RESET - Press this button to cancel any changes to the Treble and Bass controls. Remote Control Battery
Replacement CAUTION: When replacing the lithium battery in the remote, make sure that the replacement battery is
inserted in correct polarity. Place the battery so that its positive (+) side faces up with the tray held so that the surface
with the dot and (+) is facing up.
8. BASS -/+ Press BASS - to reduce low frequency output. Press BASS + to increase low frequency output.
9. TREBLE -/+ Press TREBLE - to reduce high frequency output. Press TREBLE + to increase high frequency output.

Flat Screen TV SOUND Platform A/V Sources
TABLE TOP INSTALLATION
The SOUND PLATFORM is ideally designed for table top installation. In this application the SOUND PLATFORM
is placed on a cabinet top and becomes a pedestal for the TV. Very little space is required beyond what is already
used by the TV.
DOWN-FIRING WOOFERS/REAR PORTS
The SOUND PLATFORM should always be placed on a solid surface, maintaining the clearance on the bottom
of the unit required for low-frequency sound to freely radiate into the room. Do not place objects next to the
SOUND PLATFORM that will block this space. The SOUND PLATFORM has two rear bass ports that enhance
low frequency sounds. These ports should remain unobstructed with a clearance of at least three inches to a
back wall to assure proper performance
Note:The TV pedestal should not be larger than the top of the SOUND PLATFORM (28”W x 16”D)
CABINET INSTALLATION
The cabinet top should be at least seventeen inches deep to properly support the SOUND PLATFORM. The
SOUND PLATFORM is sixteen and a half inches deep (with grille attached) and extra space will be required
between the SOUND PLATFORM and a wall behind the cabinet for cables connecting the SOUND PLATFORM to
the TV or other A/V sources (3 inches minimum).
SOUND PLATFORM
SOUND PLATFORM

HARDWIRED AUDIO CONNECTIONS
The JAZZ AUDIO SOUND PLATFORM has three hardwired Audio Input connections on the rear panel that can be
used for TV audio or connection to other sources such as CD player, a portable music player (that does not have
Bluetooth), a computer or any audio source with one of the following output connections.
Sound Platform
Audio Inputs
Digital Optical Audio Cable
COAXIAL DIGITAL AUDIO
Connect the Optical Digital Audio OUT on a TV
or other source to the Pro-Connect SOUND
PLATFORM Optical Input using a Digital Optical
Audio Cable as shown. This Input is selected by
pressing the ‘OPT’ button on the included IR
Remote. NOTE: The audio output of a TV, Blu-ray
Disc player, game console, or DVD player
connected to the SOUND PLATFORM via Optical
Digital, must be set to PCM in the source’s setup.
Digital connection to a CD player does not require
a special setting.
OPTICAL DIGITAL AUDIO
Connect the Optical Digital Audio OUT on a
TV or other source to the Pro-Connect SOUND
PLATFORM Optical Input using a Digital Optical
Audio Cable as shown. This Input is selected by
pressing the ‘OPT’ button on the included IR
Remote. NOTE: The audio output of a TV,
Blu-ray Disc player, game console, or DVD
player connected to the SOUND PLATFORM via
Optical Digital, must be set to PCM in the
source’s setup. Digital connection to a CD
player does not require a special setting.
Sound Platform
Audio Inputs
L&R AUDIO
Connect the L&R Audio OUT on a TV or other
source to the SOUND PLATFORM L&R Audio
Input using a Stereo RCA-RCA Patch Cable as
shown. This Input is selected by pressing the
‘AUX’ button on the included IR Remote.
Sound Platform
Audio Inputs
AC POWER CORD
After all audio connections have been made and
confirmed, connect the female end of the included
power cord to the AC Input on the SOUND
PLATFORM rear panel, and then plug the AC
power cord into an un-switched AC outlet. The
AC connection is a universal power connection
that will automatically handle AC voltage from
100-240VAC.
Sound Platform
Audio Inputs

SIMULATED SURROUND
The SOUND PLATFORM utilizes advanced Digital Signal Processing (DSP) to create simulated surround sound
from a stereo speaker configuration. The SOUND PLATFORM simulated surround can also be used for music.
Press the SURR button on the SOUND PLATFORM IR Remote to turn the simulated surround ON. Front panel
Status LED will flash once.
Press the SURR button on the SOUND PLATFORM IR Remote to turn the simulated surround OFF. Front panel
Status LED will flash once.
OPERATING THE JAZZ AUDIO SOUND PLATFORM
PAIRING AND SELECTING A BLUETOOTH SOURCE
The SOUND PLATFORM will pair without the need to enter a code, if the device implements Bluetooth v2.1 or
later. Legacy pairing is the only method available for Bluetooth v2.0 and older. Each device must enter a PIN
code: ‘0000’ to complete pairing. To ensure that your device is compatible, look for the Bluetooth Music Icon on
the packaging, or go to: www.gadgetguide.bluetooth.com
PAIRING A BLUETOOTH DEVICE
1. Turn the SOUND PLATFORM and the Bluetooth device ON.
2. Press the button on the SOUND PLATFORM IR Remote to select the Bluetooth Input. The front panel Status
LED flash twice, delay then repeat.
3. On the device to be paired to the SOUND PLATFORM, turn Bluetooth ON. The Bluetooth controls are typically
found in the device’s ‘Settings’ or ‘Connections’ menu. If the Bluetooth device has previously been paired with the
SOUND PLATFORM, and the SOUND PLATFORM has not been removed from the list of discovered devices, the
Bluetooth device should automatically sync with the SOUND PLATFORM. (Front panel Status LED solid blue.)
4. Press the button on the SOUND PLATFORM IR Remote for a Bluetooth device that has not been paired with
the SOUND PLATFORM, or the SOUND PLATFORM has been removed from its list of discovered devices. The
SOUND PLATFORM will output a sync code that will be received by the Bluetooth device. The front panel Status
LED will flash rapidly until the Bluetooth device accepts the BT Code and pairs to the SOUND PLATFORM.
5. The device will appear in the Bluetooth setup screen on the device being paired.
6. The device should sync to the SOUND PLATFORM. The front panel Status LED will stop flashing and
illuminate solid blue.
7. If switching between hardwired sources and a paired Bluetooth device, the Bluetooth device will remain
‘connected’ as long as the device has not been turned OFF or moved out of Bluetooth range. If the Bluetooth
device has been turned OFF, simply turn it ON, navigate to the device’s Bluetooth setup and sync to the SOUND
PLATFORM

SPECIFICATIONS AUDIO
Power Output 20W Continuous x 4 Channels into 4O for 80 Watts Total Amplification;........
THD (at rated power)...................................................................................
Damping Factor.........................................................................................
Input Sensitivity (For rated power @ max VC, analog L&R Inputs)...............................
Input Impedance (analog L&R Inputs)................................................................
Input Overload (analog L&R Inputs)..................................................................
Frequency Response..................................................................................
Channel Separation....................................................................................
Cross Talk Between Sources..........................................................................
S/N Ratio (A-Wtd, db below 1 Watt)..................................................................
Bass Control Range.....................................................................................
Treble Control Range..................................................................................
35Hz to 20kHz
<1.00%
> 15
335 mV 20 K
Ohms 2.0Vrms
35 Hz to 20
kHz > 50 dB @
10 kHz > 60 dB
@ 10 kHz -78
dB ± 8 dB @
100 Hz ± 6 dB/-
10dB @ 10 kHz
Speakers
Down-firing Subwoofers................................................................................
Mid Range Drivers......................................................................................
Tweeters.................................................................................................
Two x 5-1/4” Treated Paper Cone
Four x 2-1/2” Treated Paper Cone
Two x 1” Silk Dome
Power Consumption 120V
Standby..................................................................................................
No signal (idle)..........................................................................................
At 1/8 of Rated Power (2.5 Watts/Channel, 4O).....................................................
Rear Panel marked Line Ratings......................................................................
<0.5 Watts
14 Watts
40 Watts
100~240V~ 50~60Hz 100W
Dimensions : (H x W x D) 4” x 28” x 16-1/2” (102mm x 711mm x 419mm)
16” (406mm) Depth with grille removed
Weight : 25 lbs. (11kg)
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by OSD Audio is under license. Other trademarks and trade names are those of their respective owners.
Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates audio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

LIMITED TWO-YEAR WARRANTY
Limited Warranty
Pro-Connect warrants to the original retail purchaser only (“you”) that this product will be free from defects in
materials and workmanship for a period of two years (the “Warranty Period”), subject to the limitations and
exclusions set out in this Limited Warranty. This warranty is not transferable to subsequent owners of the
product. If you discover a defect in material or workmanship within the Warranty Period, contact Pro-Connect
NOTE
JAZZ Audio, 775 Columbia ST
Brea, CA 9