Odys ODYS - LOOP User manual
0 1
INSTRUCTION MANUAL
ODYS - LOOP
PORTABLE STEREO MUSICSTATION
FOR iPod/iPhone
With FM RADIO
Please read following instructions prior to operating your unit.
Manufacturer of this unit follows a principle of continuous improvement and has no
responsibility for any changes that are made to the unit nor any liability for these changes.
Thanks for your choice of our products.
Disclaimer
All the information, design and specifications contained in this manual were correct
at the time of publication. However, as the product is under development and
upgrading, the final device may have a slightly difference in appearance or modified
functionality than presented in this manual.
Package Content
1. ODYS Loop
2. Remote Control (incl battery)
3. Adapter for iPod/iPhone
4. Manual
5. Warranty Card
Safety Instructions
Although this product is safe, please observe the following information and warnings.
•Do not expose the device to direct sunlight, extreme heat or cold, damp or dusty conditions.
Malfunctions and damage and can occur as a result..
•Do not use the device in an extremely dry environment to avoid static electricity.
•Do not shake the device or subject it to hard knocks. The device may be damaged if it falls.
Do not place any heavy objects on top of the device.
•Clean the device only using a soft, dry cloth and do not use any volatile substances, such as
solvents, to avoid damaging the surface.
•Do not open the casing of the device under any circumstances, and do not attempt to repair
or modify the device.
Disposal
Do not dispose of a defective device in normal household waste disposal containers
Take the defective device to your retailer or to an appropriate waste collection site. This
will ensure that the device is disposed of in an environmentally-friendly way.
Support
URL: http://www.odys.de
See our website for the latest information on this device, on other products by our company
and on our company itself. Any firmware updates for this device are also made available on
our website. If you have questions or problems, please read the FAQs on our website or
2 3
MAIN UNIT
1. HANDLE
2. SLEEP BUTTON
3. LCD DISPLAY
4. STOP BUTTON
5. FM TELESCOPIC ANTENNA
6. SPEAKERS
7. POWER BUTTON
8. SOURCE BUTTON
9. VOLUME - BUTTON
10. VOLUME + BUTTON
11. iPod/iPhone DOCKING PUSH
OPEN AREA
12. TUNING - BUTTON
13. TUNING + BUTTON
14. PLAY/PAUSE BUTTON
15. MEM BUTTON
16. VIDEO OUTPUT JACK
17. LINE IN JACK
18. BATTERY COMPARTMENT
19. AC CORD
20. REMOTE SENSOR
REMOTE CONTROL
1. POWER BUTTON
2. SLEEP BUTTON
3. iPod MENU BUTTON
4. MENU UP BUTTON
5. PREVIOUS & FAST BACKWARD
BUTTON
6. ENTER BUTTON
7. MEM BUTTON
8. MENU DOWN BUTTON
9. TREBLE +/- BUTTON
10. BASS +/- BUTTON
11. MUTE BUTTON
12. SOURCE BUTTON
13. NEXT & FAST FORWARD
BUTTON
14. PLAY/PAUSE BUTTON
15. VOLUME +/- BUTTON
POWER SUPPLY
Plug AC plug into the outlet socket on the unit for connecting the main power.
SLEEP TIMER SETTING
Following the below instructions to set the sleep timer:
During playback, press SLEEP button repeatedly to cycle through the sleep time options:
90 ⎝80 ⎝70 ⎝60 ⎝50 ⎝40 ⎝30 ⎝20 ⎝10 ⎝00
After the sleep time setting, you can play the unit freely. Once the sleep time is expired, the
unit will be switched off.
During playback, press SLEEP button to check the remaining sleep time.
iPod/iPhone OPERATING
PLAYING AN iPod/iPhone
1. Press iPod/iPhone DOCKING PUSH OPEN AREA to pop out the docking. Dock the
iPod/iPhone on to the unit. Power on the unit, then press SOURCE button repeatedly to
switch to iPod mode, and then the playback will start automatically.
2. Press PLAY/PAUSE button to start or pause the playback.
3. Press STOP button to stop the playback.
4. During playback, press TUNING + button on the unit or NEXT/FAST FORWARD button
on the remote to skip to the next track; press and hold TUNING + button on the unit or
NEXT/FAST FORWARD button on the remote to search through the track forward.
5. During playback, press TUNING - button on the unit or PREVIOUS/FAST BACKWARD
button on the remote to skip to the previous track; press and hold TUNING - button on the
unit or PREVIOUS/FAST BACKWARD button on the remote to search through the track
backward.
6. Press iPod MENU button on the remote to return back to the iPod menu, press MENU
UP/DOWN buttons to select your desired track for playback, press ENTER button to
confirm.
FM RADIO
TUNING THE FM RADIO
1. Power on the unit, switch to RADIO mode by pressing SOURCE repeatedly.
2. Press TUNING +/- button on the unit or NEXT/PREVIOUS button on the remote to fine
tune radio station. Press and hold TUNING +/- button on the unit or NEXT/PREVIOUS
button on the remote to auto search radio station forward or backward respectively. When
an available station will be found, the unit will broadcast it immediately and the searching
will be stopped.
1 2 3 4 5
6 7 8 9 610 11 12 13
14
15
16 17 18 19
1
23
45
67
8
9
10
11
12
13
14
15
20
4 5
STORING YOUR FAVORITE RADIO STATION
1. During playback, press and hold MEM button on the unit or short press MEM button on
the remote for storing the current station, a memory cell number flashes on the screen.
2. Use TUNING +/- button on the unit or MENU UP/DOWN button on the remote to select
the corresponding memory cell among P01-P20 for storing the station.
3. Confirm your selection by pressing MEM button on the unit or on the remote.
4. During radio playback, press MEM button on the unit, and then press TUNING+/- button
on the unit to recall the stored stations. You also can press MENU UP/DOWN button on
the remote repeatedly to select your desired stored stations for broadcasting.
MUTE THE UNIT
During playback, press MUTE button to switch off the audio. Press the button again to
resume the audio.
VOLUME LEVEL/TREBLE/BASS ADJUSTMENT
Press VOLUME +/- button or TREBLE +/- button or BASS +/- button to adjust the volume
output level or treble effect or bass effect.
CONNECTING WITH OTHER APPLIANCES
LINE IN
Follow steps to connect the unit to another audio device:
1. Connect the device into the player’s LINE IN jack with the LINE OUT cables.
2. Press POWER button to turn the unit on.
3. Press SOURCE button repeatedly to switch the unit to LINE IN mode.
4. Power on the device and begin play.
VIDEO OUTPUT
1. Dock a iPod/iPhone to the unit.
2. Connect RCA cable to the VIDEO OUTPUT jack on the unit and the TV set.
3. Power on the unit and the connected TV set. Press SOURCE button repeatedly to switch
to iPod mode.
4. Change the TV set to the proper input mode.
5. Video from a docked iPhone/iPod can now be played through the bar speaker to the
connected television.
Note: Make sure the docked iPhone or iPod’s TV out option is turned on.
TROUBLE SHOOTING
Symptom Possible Cause Solution
Radio sound distorted. 1. The station is not tuned in.
2. The signal is poor.
1. Fine tune the station.
2. Extend the FM telescopic
antenna, change the direction
of the antenna.
No radio sound. 1. The unit is not in tuner
mode.
2. The volume has been
muted or is on the minimum
setting.
1. Press SOURCE button
repeatedly until switching to
tuner.
2. Adjust the volume level or
press MUTE button to resume
audio.
The iPod will not play 1. The unit is not in iPod
mode.
2. The iPod is not connected
correctly.
1. Press SOURCE button
repeatedly until switching to
iPod.
2. Reconnect the iPod.
No iPod sound. 1. The unit is not in iPod
mode.
2. The volume has been
muted or is on the minimum
setting.
1. Press SOURCE button
repeatedly until switching to
iPod.
2. Adjust the volume level or
press MUTE button to resume
audio.
6 7
IMPORTANT SAFETY INSTRUCTIONS
yThe apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
yWhen the mains plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable. To be completely disconnected the
power input, the mains plug of the apparatus or the appliance coupler shall be
disconnected from the mains completely.
yNo naked flame sources, such as lighted candles, should be placed on the apparatus.
yMinimum distances 2.0cm around the apparatus for sufficient ventilation. The ventilation
should not be impeded by covering the ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
yThe use of apparatus is in tropical and/or moderate climates.
yAttention should be drawn to the environmental aspects of battery disposal.
yCAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
yBattery shall not be exposed to excessive heat such as sunshine, fire or the like.
yThe marking plate is located at the bottom of the apparatus.
Play&Charge Video Output Bracket
iPhone
iPhone ●●12
iPhone 3 ●●12
iPhone 3GS ●●12
iPhone 4 ●●
iPod Touch
iPod Touch 1st generation ●●14
iPod Touch 2nd generation ●●14
iPod Touch 3rd generation ●●14
iPod Touch 4th generation ●●
iPod nano
iPod nano 1st generation ●8
iPod nano 2nd generation (aluminium) ●8
iPod nano 3rd generation (video) ●●13
iPod nano 4th generation (video) ●●8
iPod nano 5th generation (video camera) ●●8
iPod nano 6th generation ●●
iPod and iPod mini
iPod Classic 80GB ●●10
iPod Classic (2007) 160GB ●●10
iPod Classic (2009) 120/160GB ●●10
iPod 4th generation 20/40 GB ●10
iPod 4th generation (colour display) 20/30 GB ●●10
iPod 4th generation (colour display) 40/60 GB ●●
iPod 5th generation (video) 30/60/80GB ●●10
iPod mini ●
8 9
Warranty Conditions
The following conditions comprise the requirements and scope of our warranty conditions
and do not affect our legal and contractual warranty obligations.
We offer a warranty on our products in accordance with the following conditions:
1.AXDIA products are covered by a 24 month warranty. We will resolve damages or
defects on AXDIA products free of charge within 12 months of the purchase date
under the following warranty conditions. For any damage or defect determined later
than 12 months after the purchase date, proof of a manufacturing fault must be
submitted for repair under warranty.
The warranty does not cover batteries and other parts, which are considered
consumables, parts that break easily such as glass or plastic or defects based on
normal wear and tear. There is no warranty obligation in the event of marginal
differences compared to the target appearance and workmanship provided these have
a negligible effect on the product's fitness for use, in the event of damage caused by
chemical or electrochemical effects, by water or generally from abnormal conditions.
2.The warranty will be performed in such a way that we shall decide whether to repair
the defective parts or to replace them with working parts free of charge. AXDIA
reserves the right to exchange the product for a replacement product of equal value if
the product that is sent in cannot be repaired within a reasonable time or at reasonable
cost. The product can also be exchanged for a different model of the same value.
Requests cannot be made for repairs to be carried out on site. Parts that have been
replaced or exchanged become our property.
3.The warranty claim does not apply if repairs or other work is carried out by
unauthorized persons or if our products are equipped with additional parts or
accessories that are not approved for our products.
4.Warranties that have been activated do not cause the warranty period to be extended,
nor do they trigger a new warranty period. The warranty period for any replacement
parts installed ends with the warranty period for the entire product.
5.Any other or further claims are excluded, especially those for replacement due to
damage caused outside of the product, provided there is no obligatory legal liability.
We therefore accept no liability for accidental, indirect or other consequential damage
of any kind, which leads to usage restrictions, data loss, loss of earnings or
interruption to business.
Asserting a warranty claim
1.To make use of the warranty service, you must contact the AXDIA Service Center by
e-mail, fax or phone (see below for contact details). You can also use the service form
on our website or on the back of the warranty conditions.
2.AXDIA Service Center will try to diagnose and solve your problem. If it is determined
that a warranty claim exists, you will be given an RMA number (Return Material
Authorization) and you will be asked to send the product to AXDIA.
IMPORTANT: AXDIA will only accept parcels that have an RMA number.
Please observe the following when sending the product:
1.Send the product suitably packaged with carriage and insurance paid. Do not enclose
any accessories with the products (no cables, CD's, memory cards, manuals, etc.),
unless the AXDIA Service Centre specifies otherwise.
2.Mark the RMA number on the outside of the package in such a way that it is visible
and clearly legible.
3.You must enclose a copy of the sales slip as proof of purchase.
4.Once AXDIA has received the product, it will meet its warranty obligations in
accordance with the warranty conditions and will return the product to the sender with
carriage and insurance paid.
Service outside of warranty
AXDIA can refuse any service claim made that is not covered by the warranty. If AXDIA
agrees to provide a service outside the warranty, the customer will be invoiced for all repair
and transport costs.
AXDIA will not accept any packages that have not first been approved by AXDIA by means
of an RMA (Return Material Authorization).
Table of contents
