jbc UC1000 User manual

UC1000
USB CABLE ADAPTOR
www.jbctools.com

2
Before proceding any operation
is advisable to read the instructions
-Ensure that the station is not connected to the electrical
network, otherwise there is a risk of electrical shock during
the internal manipulation.
-Dissassembly operation must be performed by a qualified
person.
-Is convenient to work in an ESD safe area and use antiestatic
protection methods, otherwise do not touch internal parts
of the station even when it is disconnected, to avoid ESD.
-Dissassemble the station on a soft surface to prevent
cover damages.
* UPDATER PROGRAM NEEDED contact your distributor.
SAFETY RECOMENDATIONS
!
UC1000 / USB CABLE ADAPTOR
UC1000
USB CABLE ADAPTOR
ww w.j bc too ls. com

3
Unscrew the lid. (4 screws)
Connect the USB cable adaptor into the frontal
circuit socket.
Carefully remove the lid.
Place the lid without screwing.
Plug the power cord. Plug the USB cord to the PC.
Turn the station ON.
Reprogram the station (see software manual).
Once the programming operation it’s done:
-Turn OFF the station
-Unplug the power cord from the station
-Unplug USB cable from the PC and the station
-Assembly the lid. Take care of the jumpers, ensure that they are well connected.
-Screw the Lid.
DD/DM/HD CONTROL UNITS/ DISSASSEMBLY

4
Unscrew the lid. (4 screws)
Connect the USB cable adaptor into the frontal
circuit socket.
Carefully remove the lid.
Place the lid without screwing.
Plug the power cord. Plug the USB cord to the PC.
Turn the station ON.
Reprogram the station (see software manual).
Once the programming operation it’s done:
-Turn OFF the station
-Unplug the power cord from the station
-Unplug USB cable from the PC and the station
-Assembly the lid. Take care of the jumpers, ensure that they are well connected.
-Screw the Lid.
DI CONTROL UNIT/ DISSASSEMBLY

5
Unscrew the housing. (5 screws)
Connect the USB cable adaptor into the frontal
circuit socket.
Carefully remove the housing.
Place the lid without screwing.
Plug the power cord. Plug the USB cord to the PC.
Turn the station ON.
Reprogram the station (see software manual).
Once the programming operation it’s done:
-Turn OFF the station
-Unplug the power cord from the station
-Unplug USB cable from the PC and the station
-Assembly the cover. Take care of the jumpers.
-Screw the housing and stick the bumper.
COMPACT LINE UNITS / DISSASSEMBLY

Unscrew the housing. (4 screws)
Connect the USB cable adaptor into the socket.
Carefully remove the housing.
Place the housing without screwing.
Plug the power cord. Plug the USB cord to the PC.
Turn the station ON.
Reprogram the station (see software manual).
Once the programming operation it’s done:
-Turn OFF the station
-Unplug the power cord from the station
-Unplug USB cable from the PC and the station
-Assembly the cover. Take care of the jumpers.
-Screw the housing.
NANOSTATION CONTROL UNITS / DISSASSEMBLY
6

7
Unscrew the housing.
(4 screws)
To have access to the connection you need loose
the screws and release the frontal part carefully
Carefully remove the housing.
Connect the USB cable adaptor into the socket.
Plug the power cord. Plug the USB cord to the PC.
Turn the station ON.
Reprogram the station (see software manual).
Once the programming operation it’s done:
-Turn OFF the station
-Unplug the power cord from the station
-Unplug USB cable from the PC and the station
-Assembly the cover. Take care of the jumpers.
-Screw the housing and stick the bumper.
JT/TE HOT AIR STATIONS / DISSASSEMBLY

WARRANTY
JBC’s 2 years warranty guarantees this equipment against all manu-
facturing defects, covering the replacement of defective parts and
all necessary labour.
Warranty does not cover product wear due to use or mis-use.
In order for the warranty to be valid, equipment must be returned,
postage paid, to the dealer where it was purchased enclosing this
fully filled in, sheet.
www.jbctools.com
SERIAL Nº
STAMP OF DEALER
DATE OF PURCHASE
0010103-0512
This product should not be
thrown in the garbage.