JD Williams Ltd. QN917 User manual

Dimensions
Width - 20cm
Depth - 20cm
Height - 80cm
Important– Please read these instructions fully before starting assembly
Assembly Instructions- please keep for future reference
464/3944
New England Toilet roll cupboard
Issue 1 - 16/05/2016
QN917

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers

2
Components -Panels
Please check you have all the panels listed below
Components - Fittings
Note:
may be supplied than are required.
Tools required
Phillips screwdriver
(medium & large)
1x1 2x1 34
56 7 x1
x1
x1
x1
x1
20X20X1.2cm 77.7X18.5X1.2cm 77.7X18.5X1.2cm 20X20X1.2cm
77X20X1.2cm 17.5x17X1.2cm 78.5X18.3X0.3cm
x4
AB
x8 x8 D
Cx8 x2 E
IJKL
x1
x1
x3
5.8x30mm
Mx1
Fx1 G x1 Hx1
x1 Nx1

3

4
Assembly Instructions
Step 1
Step 2
2
C
C
4
C
3
6
C
C
C
C
C
C
C
B
C
B
C
B
C
B
1. Into Left Side Panel 2
and Right side Panel 3,
insert 4 x Male
Camlocks B as shown.
Connect panels 2 , 3
and 6 together as
shown and insert
4 x Female Camlocks C
in locations shown.
Tighten with a Phillips
Screwdriver
2
3
C
B
23
6
C
C
1. Insert 4 x Dowels A
into the bottom edge of
panels 2 and 3 as
shown.
2. Insert 2 x Male
Camlocks into base
panel 4.
3. Connect Panels as
illustrated and insert 2 x
Female camlocks into
panels 2 and 3.
Tighten with a Phillips
screwdriver
C
C
C
C
C
C
2
3
23
C
B
C
B
C
B
4
4
C
A
C
A
C
A
C
A
C
A
23

5
Assembly Instructions
Step 3
Step 4
1
5
1. Slide Back Panel 7
into position shown
77
1
5
C
A
C
A
C
A
C
A
C
B
C
B
C
C
C
C
C
D
C
D
1. Into The underside of
Top Panel 1 insert 2 x
Male Camlocks B
2. Insert 4 x Dowels A
into the Top edge of
panels 2 and 3 as
shown
3. Insert 2 x Hinge Pins
into the top and
bottom of door panel 5
4. Locate bottom hinge
into bottom panel and
locate top hinge into hole
in the underside of top
panel 1 as you connect
top panel 1 to the unit.
5. Insert 2 x female
camlcoks into holes
shown and tighten with a
Phillips Screwdriver
1
C
B
C
A
2
3
23
C
D
5
C
C
4
4
1
1

6
Assembly Instructions
Step 5
Step 6
2.Move the unit into
desired position.
3. Mark the wall with a
suitable scribe the
position of the fixing
holes.
4. Drill hole and insert 1 x
wall plug D
5. Connect to the wall
using 1 x screw D
as shown
Warning:
Before driling,check
wall for hidden pipes
and cables.
O
Warning:
The unit
is heavy.
Lift with care.
C
M
C
M
Assembly Complete
1. On the reverse of the
unit, in position shown,
fix 1 x Wall Straps
using 1 x Screws L
This unit is floor standing
but we recommend
C
I
C
L
C
K
C
K
C
K
C
K
C
J
C
I
C
I
C
F
C
H
C
G
C
E
C
M
C
I
C
L
C
M
1.Connect your choice of
handle either G or N
using screw H
2. Connect Catch Plate F
using 1 x Screw E
3. Connect Magnetic
Catch J using 2 x Screw I
4. Add 4 x Protective feet
K
C
G
C
N
C
H
C
F
C
E
C
J
C
I
C
K