hygena Valencia User manual

MADE IN
BRITAIN
Dimensions
Width - 30cm
Depth - 59cm
Height - 213cm
Valencia - 300mm Larder Cabinet
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 04/08/14
Important - Please read these instructions fully before starting assembly
ALR2722
hygena
758/4457
758/4464
758/4471
205/3787
758/4488
205/4676
Issue 2 - 04/08/14 - Replaced Grey and Plum codes with Oak and White HN codes.
Cabinet
Black Door Pack
Cream Door Pack
Oak Door Pack
White Gloss Door Pack
White HN Door Pack

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 45kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill

Components - Panels
Please check you have all the panels listed below
2
1
80%
x 2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
2
4
3
5
6
7
Left Side (DPF106B)
(1980 x 560mm)
Right Side (DPF107B)
(1980 x 560mm)
Back (DPF1149A)
(280 x 1978mm)
Loose Shelf (DPF071A)
(268 x 431mm) x 3
Horizontal (DPF070A)
(269 x 494mm) x 3
Door (DPF146A)
(297 x 716mm)
Larder Door (DPF1150A)
(297 x 1258mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 18
B
Metal dowel (F901) x 12
C
D
Large locking
nut (F900) x 12
F
G H I a
I c
I d
I e
I b
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
13mm Screw (F63) x 10
E
13mm Screw (F79) x 2
Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2
L M
25mm Screw (F50) x 6
N
Hinge Cover (F119) x 5
Bracket (F945) x 2 Shelf support (F110) x 12
Hinge Plate
(F117) x 5
Hinge Arm (F118) x 5
Leg Bracket
(F127) x 2
Leg Socket
(F120) x 4
Leg Clip
(F128) x 2
16mm Screw
(F129) x 16
Leg (F122) x 4
hygena
O
O
a
b
25mm Screw (F132) x 4
Handle (F214) x 2
45mm Screw (F65) x 4
P

4
Step 1
J
E
Step 2
Prepare the left side
Refer to step 1 and, if
required, fit 5 hinge
plates onto the left
side , as shown.
Screw 6 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit a bracket
to the left side
using screw ,
flush with the top
edge and back
edge, see
diagram.
B
B
B
B
B
B
B
B
L
L
L
L
L
J
J
1
1
1
1
1
E
Choose which way
you would like the
doors to open
You can fit the doors to
the left side or right side.
Assembly Instructions If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1
L
L
If you would
like your doors
to open this
way, fit the
hinge plates to
the left side
If you would
like your doors
to open this
way, fit the
hinge plates to
the right side

5
Step 3
Step 4
Assembly Instructions
Step 2
J
E
B
B
B
B
B
L
L
L
L
J
1
1
1
L
L
B
B
L
J
E
Prepare the right side
Refer to step 1 and, if
required, fit 5 hinge
plates onto the right
side , as shown.
Screw 6 metal dowels
into the holes shown on
the right side .
Fit a bracket to the
right side , flush with
the top edge and back
edge, see diagram.
Secure the bracket
using screw .
2
B
2
J
J
2
E
B
B
B
B
B
B
L
L
L
L
J
2
2
2L
L
A
A
A
A
A
A
C
C
C
Prepare the 3
horizontals
Insert 4 large locking
nuts into each of the
3 horizontals .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 6 wooden dowels
into each of the 3
horizontals .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
C
C
4
10mm
A
A
4
4
Cx 3

Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 5
Join the horizontals to
the right side
Push the horizontals
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each horizontal .
Note: Turn the large
locking nuts as far
as they will go - more
than 1/2 a turn.
4
4
2
C
C
Step 6
B
C
4
2
I a
I b
b:
a:
c: d:
Fit the legs to one of
the horizontals
a: Push the leg sockets
. into the holes in
one of the horizontals
b: Secure each leg
socket with 3
screws .
c: Tap in the centre plug
on each leg socket .
d: Push the leg into
the leg socket .
I a
I a
I a
I e
I e
4
x 3
I a
I a
I b
I a
I a
I a
4
I a
NOTE: Hinge plates are not
shown as you may have
fitted them to the left side.
4
x 1
Horizontal
with feet
4
Finished
front edge
.

Assembly Instructions
7
Step 7
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the 3 horizontals .
Note: Turn the large
locking nuts as far
as they will go - more
than 1/2 a turn.
1
C
4
1
4
4
4
C

Assembly Instructions
8
Step 8
a:
b:
Fit the back
a: Slide the back
along the grooves in the
side panels and .
3
1 2
b: The bottom edge of
the back must be
flush with the bottom
edge of the horizontal
with the feet .
Secure the back to
the unit using 2 screws
. into the back edge of
each of the 3 horizontals
. .
Stand the unit up for
the next stage.
3
3
4
4
F
3
1
2
Note: These 2
holes must be
nearest the bottom
edge of the panel.
F
F
F
F
F
F3
4
Note: The bottom
of the back must
be flush with this
horizontal.

9
Assembly Instructions
Step 9
Warning: Take
care when
drilling the wall
that you do not
drill into any pipes, wires
etc. If in doubt, consult
an expert.
Secure the unit to the
wall
Using the brackets
fitted to the back edge of
the sides and
screw the unit to the
wall.
Fixings are not supplied
as they will need to suit
the wall type, and the
length of screw will
depend on the distance
of the back of the unit to
the wall.
F
1 2
5mm
G
H
Joining units together
Fittings have been
supplied so you are able
to join units together.
Make sure that your first
unit is level.
Push the other unit up
against first unit and
ensure both units are
level.
Check that the ends are
flush and in line, then
clamp them together.
Using a 5mm drill bit,
drill 2 holes (example of
positions shown circled)
in the side panel into the
adjoining side panel of
the other unit.
Push the connecting
sleeves into the holes
and then screw the
connecting bolts in
from the other side.
G
H
Step 10
2
1
2
1
F
F