Jegs 81553 User manual

Installation Instructions for 81553
Parts Washer
40 Gallon
PARTS
NUMBER
DESCRIPTION
QTY
1
COVER
1
2
WORK BASKET
1
3
SPRING PAN
4
4
PIN
4
5
SAFETY PLATE
1
6
WORK SHELF
1
7
BODY
1
8
SPRING WASHER
24
9
NUT
24
10
O-RING
1
11
PLUG
1
12
SHELF
1
13
LEG
4
14
PAN SCREW
24
15
NUT
5
16
SPRING WASHER
5
17
SCREW
5
18
STRAIN RELIEF
2
19
CABLE AND PLUG
1
20
PUMP HOUSING
1
21
SCREEN
1
22
SWITCH
1
23
SWITCH BOX
1
24
FLEXIBLE PIPE
1
25
ELBOW SEAT
1
26
PUMP BODY
1
27
PUMP BACK COVER
1
28
FILTER COVER
1
29
PUMP HOUSING COVER
1
30
ELBOW
1
31
PLASTIC WASHER
1
32
SPIGOT
1
33
LOCATION OF KNOB
1
34
FILTER
1
35
SEAL RING
1
36
IMPELLER
1
37
SHIN WASHER
2
38
SEAL RING
1
39
IMPELLER HOLDER
1
1-800-345-4545 jegs.com

Assembly
1. Remove machine from packaging and inspect for any visual damage.
2. Remove parts inside the machine.
3. Lay clean hard cardboard on the floor and lay machine on its lid. Make sure you hold cover
closed when laying machine on its lid.
4. Mount four legs on brackets with M6 x 12 Philips head screws and M6 nuts. NOTE: DO NOT
TIGHTEN.
5. Place lower shelf between legs with flat surface up and attach to legs with M6 x 12 Philips head
screws and M6 nuts.
6. With legs pressed tight against lower shelf, tighten all screws to lower shelf.
7. Tighten all the screws installed in step 4.
8. Stand machine up. Be careful to hold lid closed.
9. Put work shelf and basket into the machine.
10. Mount pump assembly into slot on the side of the machine then place filter screen in position.
11. Plug machine into standard 115Volt/ 60Hz grounded outlet and fill with proper amount of fluid.
12. Turn switch on. Fluid should now be flowing from the flexible spigot.
SPECIFICATIONS
Recirculating Parts Washer
Overall Dimensions
45.28”x 22.05”x 35.43”
Tank Dimensions
44.69”x 21.46”x 12.6”
Max Solvent Capacity
40 Gallons
Max Pump Output Through Spigot
5.28 gpm
Electrical Requirements
115V/60Hz/O.5A
Gross Weight
99.21 lbs.
1-800-345-4545 jegs.com

Cleaning Solutions
Approved cleaning solutions: Water/household detergents (PH6 ~8)
Warning
The pump of your Parts Washer may be damaged if you use solvents other than those listed above
such as methyl ethyl ketone (MEK), Perchloroethylene or trichloroethylene.
Trouble Shooting
The only trouble you should ever experience with your Parts Washer is reduced flow volume of
cleaning liquid from the flex hose nozzle.
The probable cause is foreign matter in the flex hose.
Corrective Procedure
1. Check if indicator light on switch box is lit.
2. Using an insulated handle screw driver to lightly touch tip of housing of motor. A light oscillation
magnetic pull indicates power is reaching the motor.
3. Disconnect power plug, remove flex hose from pump flow-out line.
4. Remove front of pump housing by removing 3 screws. Clean any foreign matter lodged around
impeller.
5. Reassemble in reverse order.
1-800-345-4545 jegs.com