Jenn-Air AMC2206B User manual

INSTRUCTIONS

Proper installation is the installer's responsibility!
Write the model & serial numbers on the owner's
manual. The model number label is located on the oven
front.
UL Listed=For use over electric heat source
models (Wall Ovens)
• MEW5527, MEW5530, MEW6527, MEW6530
AEW3530, AEW4530
JJW8527, JJW8530, JJW9527, JJW9530
Parts, Tools, and Materials
The following parts are supplied with the oven:
Bracket Base
Left Bracket
Bottom Bracket
Top Bracket
Trim Frame
Template 1
template 2
1" Screw
(1 required, 1 extra)
1/2"Screw
(14 required, 6 extra)
Tools required to perform installation:
• Phillips Screwdriver
• Saw (Electric or Hand)
• Drill with 7/64" drill bits (Electric or Hand)
• Tape Measure
• Pencil
• Framing Square
, Level
Shipping Weight
Approximate shipping weight is 15.7(30"), 14.9(27")
Ibs.
Cutout Dimensions
Height 16 7/8"
Width 25"
Depth (min.) 23 3/4"
16 7/8"
25"
23 3/4"
Height
Electric Heat Source Model

Electrical rating of this oven:
,, 120 VAC @ 60 Hz
13 A /1100 W (USA) /1000 W (CANADA)
You need a DEDICATED 120 VAC, 60 Hz, 20 A
(USA) /15A (CANADA), fused electrical supply
(located in the cabinet with the microwave as close
as possible to the microwave) serving only the
microwave.
Check with a qualified electrician if you are not
sure whether the oven is properly grounded or if
you do not completely understand the grounding
instructions.
Do not use a fuse in the neutral or grounding circuit.
Save these instructions for the local electrical
inspectors use.
If there is an electrical short circuit, grounding
reduces the risk of electrical shock by providing an
escape wire for the electric current. This appliance is
equipped with a cord having a grounding wire with a
grounding plug.
Place the plug into a properly installed and grounded
outlet.
o Amana does not recommend use of an extension
cord.
Keep the power cord dry and do not pinch or crush
it.
Do not, under any circumstances, remove the power
supply cord grounding prong!
This appliance MUST be grounded!
/f
Do not expose yourself to excessive
microwave energyt
• DO NOT try to operate the microwave oven with the
door open.
• DO NOT tamper with or defeat the safety interlocks.
• DO NOT place objects between the microwave oven
front face and the door.
• DO NOT allow soil or cleaner residue to build up on
the flat surfaces around the microwave oven door.
DO NOT operate the microwave oven if it is
damaged.
The microwave oven door must close properly to
operate safely.
DO NOT USE THE MICROWAVE OVEN:
• If the door is bent.
If the hinges or latches are broken or loose.
If the door seals, sealing surfaces or glass is broken.
DO NOT ATTEMPT TO ADJUST OR REPAIR THE
OVEN YOURSELF!
• It should be adjusted and repaired by a qualified
technician who can check for microwave leakage
after repairing the oven.
Three-prong
(Grounding plug)
Properly polarized
and grounding outlet.

_. "UNIT" installment in Bracket Base
Remove 4 screws from the lower right and left parts
of outer panel, place "UNIT" in Bracket Base and
secure using (4) screws previously removed.
2. installment of Left Bracket
Assemble the Left Bracket to outer panel and
secure with (W') screw provided.
3. Fixing 'location screw' in cabinet
Fix (1) screw at the bottom of cabinet with use of
template 1 to Ioate position of screw in cabinet.
4. "UNIT" installment in cabinet
Push "UNIT" into the cabinet aligning fixed screw in
cabinet with hole in center rear of Bottom Bracket.
Push "UNIT" in until the front of Bracket Base
touches front of cabinet.
5. installment of Bottom Bracket
Place Bottom Bracket on Bracket Base
(Reference B) Make holes of position A fit to
Bracket Base's. Drill pilot hole with a 7/64 or #35
drill bit and secure Bottom Bracket with screws
provided.
6. installment of Top Bracket
With template 2, make 2 holes each at the upper
right and left parts of cabinet. (Others for the extra)
Secure "Top Bracket" according to the holes.

7. Installment of Trim Frame
Install Trim Frame to make contact with cabinet.
_1111,1,1,1,1,
8. installment of Trim Frame
Secure 2 painted screws each at the upper and
Lower parts of Trim Frame with door open.
26 %"
17/11r_"
27" Trim Frame
Trim Frame Dimensions
(Depth of trim Frame is7/8")
19 14" 27/_ ,_
29 3/4"
iiiiuii
30" Trim Frame

Uneinstallationcorrecterelevede la responsabilit_de
I'installateur!
Inscrivezlesnumerosde modeleetde seriedansle manuel
d'utilisation.Eetiquettedu numerode modeleest apposee
I'avantdufour.
Homologation UL-A utiliser sur des modeles a source
de chaleur electrique (fours murau×)
• MEW5527,MEW5530,MEW6527,MEW6530
° AEW3530,AEW4530
° JJW8527,JJW8530,JJW9527,JJW9530
Outils necessaires pour effectuer I'installation :
,, TournevisPhillips
,, Scie(electriqueoumanuelle)
,, Perceuseavecmechesde 7/64"(electriqueou manuelle)
,, Rubana mesurer
" Crayon
,, Equerredecharpentier
• Niveau
Poids a I'exp_dition
,, Le poidsapproximatifestde 7,12kg(30"),6,75kg(27").
Dimensions de d_coupe
Hauteur 167/8" 167/8"
Largeur 25" 25"
Profondeur(min.) 23 3/4" 23 3/4"
Pieces, outils et materiaux
Lespiecessuivantessent fourniesavecle four:
Basedusupport
\
Supportgauche
Supportinferieur
\
Supportsuperieur
B&tid'encastrement
Gabarit1
Gabarit 2
1"Support
(1requise, 1 supplementaire)
Vis W'
(14 requises, 6
supplementaires)
Modelea.sourcedechaleurelectrique
-lauteur

Caracteristiques electriques de ce four :
• 120V c.a.&60 Hz
• 13A /1100W (Etats-Unis)/1000W (Canada)
• Vousdevezutiliserune alimentationelectrique_.fusible
RESERVEEde 120V c.a., GOHz,20A (Etats-Unis)/15A
(Canada)(situeedansrarmoireavecle four&micro-ondes,
leplusprespossibledu four)desservantuniquementlefour&
micro-ondes.
• Sivous n'_tespascertain de laraise _.laterre du fourou
necomprenezpastouteslesinstructionsde raise&la terre,
consultezun electricienqualifi&
,, N'utilisezpasdefusibledartsle circuitneutreou de raise& la
terre.
• Conservezces instructionsenvue de leurutilisationpar un
inspecteuren electricitelocal.
• Encas de court-circuit,laraiseb,laterrereduitle risquede
chocelectriqueen foumissantun circuitde fuiteaucourant
electrique.Cet appareilestequiped'un cordondoted'un fil
de masseetd'une prisede terre.
• Branchezla fichedansune prisecorrectementinstalleeet
raiseb,la terre.
•Amanad_conseille I'utilisation d'une rallonge _lectrique,
•Gardezle cordond'alimentationau secet evitezde le pincer
oude le comprimer.
,, Neretirez,en aucuncas,la brochede massedu cordon
d'alimentation!
• CetappareilDOlT _tremis&la terre!
f
Ne vous exposez pas a une energie
microondes excessive t
,, Ne PAS utiliser le four Iorsque la porte est ouverte.
,, Ne JAMAIS demonter ou neutraliser le systeme de
verrouillage.
,, Ne PAS placer d'objets entre la face avant du four b.
micro-ondes et la porte.
,, Ne PAS laisser s'accumuler de la salete ou des
residus de produit de nettoyage sur les surfaces
planes autour de la porte du four & micro-ondes.
,, Ne PAS mettre le four en marche s'il est
endommag&
,, Vous devez fermer correctement la porte du four
pour I'utiliser en toute securit&
,, NE PAS UTILISER LE FOUR A MICRO-ONDES
,, Si la porte est pliee.
,, Si les charnieres ou les Ioquets sont casses ou
desserres.
,, Si les joints de la porte, les surfaces d'etanch6ite ou
la vitre sont casses.
,, N'ESSAYEZ PAS DE REGLER NI DE REPARER LE
FOUR VOUS-MEME !
,, Les reglages et reparations doivent _tre confies &
un technicien qualifie qui verifiera la presence d'une
eventuelle fuite a micro-ondes apres avoir repar6 le
four.
Prise de terre & trois broches
Prise de terre
correctement polaris_e.

1. Installation de r"UNITE" dans la base du support
Retirezles4vis des partiesinf@ieuresgaucheetdroite
du panneauexterieur,placezI'"UNITE"dansla basedu
support etfixez-laa I'aidedes(4)vis que vousavezretirees
prec6demment.
2. installation du support gauche
Montezle supportgauchesur lepanneauext@ieuretfixez-le
raide dela vis (W') fourniea ceteffet.
3. Fixation de la"vis d'emplacement" darts I'arrnoJre
Fixezune (1)vis au basde I'armoireenutilisantle gabarit1
pourrep@erI'emplacementappropriedansI'armoire.
4. installation de r"UNITE" darts I'armoire
PoussezI"'UNITE"dansrarmoire,en prenantsoind'aligner
lesvisfixeesdansle cabinetsur letrouarri@ecentraldu
supportinf@ieur.
PoussezI"'UNITE"jusqu'ace que ravantde la basedu
supporttoucheI'avantde I'armoire.
5. installation du support inf_rieur
Placezlesupport inferieursur labasedu support(Ref@ence
B) Faitescorrespondrelestrousen positionA
avecceux de la basedusupport. Percezun troude guidage
&I'aided'unemeche7/64ou #35et fixezle supportinferieur
&I'aidedesvis foumies &ceteffet.
6. installation du support superieur
A I'aidedu gabarit2, percez2 trousau niveaudes parties
sup@ieureet inferieurede I'armoire.(Lesautressenten
supplement.)
Fixezle "supportsuperieur"conformementauxtrous.

7. Installation du b_ti d'encastrement
Installezle b&tid'encastrementde sorte qu'ilsoiten contact
avec I'armoire.
La portedufouretantouverte,fixez2 vis peintesau niveau
despartiessup@ieureetinf@ieuredu b&tid'encastrement.
1 7/t6"
26 7/8"
BAti d'encastrement 27"
Dimensions du b_ti d'encastrement
(Laprofondeurdu b_.tid'encastrementest de7/8")
29 ¾ "
27/R ,,
19 1/8"
B&ti d'encastrement 30"
19 1f8"
r
,,uii