JERRY'S ARTARAMA Saint Remy User manual

Car fully r ad through all instructions
b for proc ding.
Multi-Angl Wood
Studio Eas l
www.jerrysartarama.com I 800.827.8478
Guid to Ass mbly
The Sai t Remy Multi-A gle Wood Studio Easel allows
you to pai t a d var ish eve the largest ca vas. If you
pai t small you ca actually pai t two ca vases side by
side — eve of differe t heights! It is made of smoothly
sa ded, oiled Beech wood a d is superbly crafted to
fu ctio flawlessly. It's wide mast allows you to pai t
pictures up to 60" wide a d 82" high ... plus you ca
pai t at a y a gle — eve flat — maki g it the perfect
support for art i most media!
Maximum h ight: 114 inch s
Minimum h ight: 78 inch s
Bas : 31.5 in. W×30.25 in. D
W ight: 43 lbs.

AB
I
CD
E
FG
J
(4) Brass
Pressure Plates
Part 1 (2)
H1 H2 H3
Part 6 (1)Castors (4)
Part 2 (2)
Part 3 (2)
Part 5 (1)
Part 4 (2) & 12 (2)
Part 7 (2) Part 8 (1)
Hardwar Packs*
Be sure to read through and understand all instructions before proceeding.
Carefully check the contents of the box to ensure all parts are included.
Parts*
Pack A: (4) 2 ½" bolts, (4)³/8" barr l nuts
Pack B: (16) 5/8" woodscr ws
Pack C: (2)2½" bolts, (2)³/8" barr l nuts
Pack D: (8) 1" woodscr ws
Pack E: (2) ratch t syst ms, (8)woodscr ws
Pack F: (4)2½"bolts, (4)³/8" barr l nuts
Pack G: (2)1
7/8" wood wash rs, (2) 5/8"
brass wash rs, (2) black plastic turn knobs,
(2)3"bolts
Pack H1: (2) 5/8"brass wash rs,
(2)1¾"bolts, (2)black plastic turn knobs
Pack H2: (2) 5/8"brass wash rs,
(2)2¼"bolts, (2) black plastic turn knobs
Pack H3: (2)5/8" brass wash rs, (2)5"bolts,
(2)black plastic turn knobs
Pack I: 17/8"bolts, h x wr nch
Pack J: (4) black plastic turn knobs (short)
(2) black plastic turn knobs (long)
Part 9 (2)
Part 10 (2) & 11 (2)
Part 13 (2) Base Blocks (2) *Hardware & Parts not to scale
Scr wdriv rs Includ d

STEP 6
You will n d: Pack A, Part 1, Part 2
STEP 2
STEP 3
You will n d: Pack C, Part 3, Base Assembly (step 1 & 2), Screwdriver
STEP 4
STEP 5
STEP 1
Ass mbly Instructions
Ass mbl th wood n parts as th picur shows and s cur using th hardwar from
Pack A. Th barr l nuts will b plac d into th bottom of Part 2 whil th bolts will b
ins rt d through th sid s of Part 1.Tight n th bolts into th barr l nuts.
Ins rt Part 3 into th top of th bas as shown in St p 3a. S cur to th base by
placing th barr l nut into th inn r sid of ach Part 3. Ins rt th bolt through th
bottom of th bas and tight n into th barr l nut as shown in St p 3b. R p at for
additional sid .
You will n d: Pack F, Part 6, Part 7, Part 8, Part 9, Screwdriver
Ins rt both Part 7 pi c s into th bottom of Part 6. Slid Part 8 onto th bottom of both
Part 7 pi c s. Tak both Part 9 boards and plac on th sid s of Part 6 and Part 7 as
shown. S cur th s by sliding th barr l nuts into th back sid of Part 6 and Part 7.
Ins rt th bolts through th sid s of Part 9 and tight n th bolts into th barr l nuts.
You will n d: Pack B, Castors, Base Assembly (Step 1), Screwdriver
You will n d: Pack D, Pack E, Part 4, Part 5, Screwdriver
You will n d: Pack G, Pack H1, Pack H2, Pack H3, Part 10, Part 11
You will also n d: Completed Base (Step 3), Canvas Support/Center asts (Step 4),
and th H Frame (Step 5)
Attach Part 4 to th back of Part 5 using (4)1"woodscr ws from Pack D(8 total) in
th pr -drill d guid hol s. R p at. Us th woodscr ws from Pack E to attach th (2)
ratch t syst ms to th bottom of Part 5 using th pr -drill d hol s.
Part 2 (2)
Part 3 (2)
Part 4 (2)Part 5 (1)
Part 9 (2)
Part 8 (1) Part 11 (2) Inside
Part 10 (2)
Outside
Part 7 (2)
Part 6 (1)
Pack C
Pack D
Pack G Pack H1 Pack H3
Pack H2
Pack F
Pack E
Castors (4)
Part 1 (2)
Connect here and
Connect here
Base
Assembly
(Step 1)
Pack B (16)
Pack a
Step 3a
Back View
F ont
View
Canvas Suppo t
& Cente Masts Bottom
of Pa t 5
Step 3b
Completed Base
(Step 3)
Completed Base
(Step 3)
H F ame
(Step 5)
H F ame
(Step 5)
Connect here
Canvas Suppo t
Cente Masts
(Step 4)
INSTRUCTIONS CONTINUED ON BACK PAGE
Using th suppli d Phillips scr wdriv r, turn th Base Assembly ov r and attach th
(4) castors with th (16) 5/8" woodscr ws from Pack B in th pr -drill d guid
hol s. Th r will b 4 woodscr ws for ach castor.

STEP 6 (Continu d)
STEP 7
Attach th H Frame b tw n th two uprights (Part 3/St p 3) of th Base. Whil holding
fram in plac , put th two bolts through th uprights and into th H Frame (St p 5).
Add th wood n wash rs in b tw n th upright and th H Frame as shown in Step
6a. Onc th bolt is through th H Frame, add th brass wash rs and tight n th black
plastic knob until s cur as shown in Step 6b.
Attach (1) Part 11 to th insid of th H Frame
n ar th upp r crossbar (Part 6 in St p 5). Ins rt
(1) bolt from Pack H2 through th pr -drill d
hol s in Part 11. Add th wash r, th n th knob
on th outsid of th H Frame. R p at for th
oth r sid .
Slid (1) Part 10 around th attach d Part 11
and s cur with bolt from Pack H1 on th
outsid . Add th wash r, th n th knob on th
insid of Part 11. R p at for th oth r sid .
Attach Part 10 to th Base using Pack H3 with
th knob on th outsid of th Base. R p at for
th oth r sid . All instructions are shown in
Step 6c Back View.
Step 6a Step 6b
Step 6c
Step 6d
Back View
Bottom
Canvas Suppo t
Top
Part 11
Part 10
Grooves
Part 6
Pack H2 (1)
Pack H1 (1) Part 11
slides
inside
Part 10
Pack
H2 (1)
Pack
H1 (1)
Pack
H3 (1)
Pack
H3 (1)
You will n d: Pack I, Pack J, Base Blocks, Part 12, Part 13
Part 12 (2)
Part 13 (2)
Pack I
Base Blocks (2)
Pack J
Onc compl t , tilt th as l
and slid th Canvas Support
/Center ast (Step 4) onto th
th H Frame from th bottom
cross bar (Part 8 in St p 5) into
th groov s in th upp r
crossbar (Part 6 St p 5) as
shown in Step 6d.
Attach th Base Blocks using Pack I to s cur th Base Uprights
(Step 3/Part 3) as shown in Step 7a.
Plac (2) Brass Pressure Plates into th hol s insid th groov of
Center ast as shown in Step 7b and slid both Part 12s onto th
two Center asts. S cur with (1) Long knob and (1) Short knob on
both sid s as also shown in Step 7b. Slid Part 13 onto ach Part 12.
Plac th final (2) Brass Pressure Plates into th hol s on th back of
Part 13 and s cur Part 13 into Part 12 with th final (2) Short knobs
as shown in Step 7c.
R vi w th plac m nt of knobs in Front View and Back View photos.
Short knobs
Long knobs
Short knobs
Brass Plates
Brass Plates
Step 7a
Step 7b F ont View
Back View
Step 7b