Jet 728100 Datasheet

JET

427 New Sanford Road

LaVergne, Tennessee 37086 Part No. M-728100

Ph.: 800-274-6848 Edition 1 10/2020

728100 Universal Stand

Instructions and Parts List

IMPORTANT SAFETY INSTRUCTIONS

• Review all instructions before assembling the table. Improper

assembly can cause personal injury and/or property damage.

• Do not exceed maximum load for the universal stand.

• Do not stand on this product.

• WARNING: This product can expose you to chemicals

including lead and cadmium which are known to the State of

California to cause cancer and birth defects or other

reproductive harm. For more information go to http://www.p65warnings.ca.gov.

Tools required for assembly

10mm and 16mm wrenches

(a ratcheting socket wrench will speed assembly time)

Shipping contents

1 Table

4 Upper Braces (2 Long, 2 Short)

4 Lower Braces (2 Long, 2 Short)

4 Vertical Legs

4 Adjust Legs

4 Leveling Pads

1 Instructions and Parts List

1 Product Registration Card

1 Hardware Package (728100-HP)

44 Carriage Bolt M6-1.0x16 – AA

48 Flat Washer 6mm– BB

48 Lock Washers 6mm –CC

48 Hex Nut M6-1.0 –DD

4 Carriage Bolt M6-1.0x36 – EE

Assembly instructions

Use the exploded view and parts list as guides to

assembly. Make all leg and brace fasteners only

finger tight until the entire unit has been assembled.

1. Attach the two short upper braces (#7) to the

table top (#2). Finger tighten only.

2. Place table top with short braces upside down;

use a mat or piece of cardboard underneath to

prevent scratching.

3. Assemble the four main legs (#9) and upper long

braces (#6). Finger tighten only.

4. Determine the height desired, then connect the

adjustment legs (#10) to the main legs. These

can be repositioned later if needed. (It is

recommended that each adjustment leg be

secured by at least 4 screws to the main leg.)

5. Determine placement of lower braces (#13/14),

and assemble them to the main legs/adjustment

legs.

6. Install the leveling foot pads (#12) and tighten

each hex nut (#11) against the adjustment leg. If

using the optional swivel casters, install those

instead of the pads.

7. Turn the unit over and push down lightly to make

sure stand rests evenly upon the floor.

8. Fully tighten all fasteners. Make any additional

leveling adjustments using the pads.

Holes are provided in the lower braces for attaching a

user-made shelf, not provided.

CAUTION: If casters are used, they must be

locked before operating a machine on the stand.

728100 Universal Stand – Exploded View

To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m.

CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve

you quickly and accurately.

728100 Universal Stand – Parts List

Index No. Part No. Description Size Qty

1 ................. 728100-001 ................. Carriage Bolt ................................................................ M6-1.0x40 ....................... 4

2 ................. 728100-002 ................. Table (Plywood Top).................................................... ........................................1

3 ................. TS-1550041 ................ Flat Washer.................................................................. 6mm ..............................48

4 ................. TS-2361061 ................ Lock Washer ................................................................ 6mm ..............................48

5 ................. TS-1540041 ................ Hex Nut........................................................................ M6-1.0 ...........................48

6 ................ 728100-006................. Upper Brace Long........................................................ ........................................2

7 .....................728100-007 ................. Upper Brace Short ....................................................... ........................................2

8......................728100-008 ................. Carriage Bolt ................................................................ M6-1.0x16.....................44

9 ..................... 728100-009................. Vertical Leg .................................................................. ........................................4

10 ............... 728100-010 ................. Adjustment Leg Weldment (#10-1 thru 10-3) ............... ........................................4

10-1 ............... .................................... Adjustment Leg ............................................................ ........................................4

10-2 ............... .................................... Glide Plate ................................................................... ........................................4

10-3............ .................................... Hex Nut ........................................................................ M10 .................................4

11 ...................TS-2311101 ................ Hex Nut........................................................................ M10 .................................4

12 ...................728100-012................. Bolt with Leveling Pad.................................................. M10 .................................4

13 ...................728100-013................. Lower Brace Short ....................................................... ........................................2

14 ...................728100-014................. Lower Brace Long........................................................ ........................................2

15 ............... 728100-015................. JET Logo with Adhesive .............................................. 4.75”x3.3” ........................1

................... 728100-016................. ID Label 728100 (not shown) ....................................... ........................................1

................... 728100-HP .................. Hardware Package (#1, #3, #4, #5, #8) ....................... ........................................1

Optional Accessory* – Swivel Caster

16 .............98-0129....................... Swivel Casters (set of 4) .............................................. .................................. 1 set

* Optional Accessory – see your dealer to order.