Jet JMEP-9 User manual

®Registered trademark of JET Equipment & Tools Ltd.
www.jetgroupbrands.com
M15-HT350551
WARNING
Please read all instructions and warnings carefully before use
• This unit is not intended for use with gasoline.
• For safety reasons, do not use the unit to extract or store dangerous chemicals, poison, acid, alkaloid, or solvents.
• Do not use the unit to extract, siphon or store petroleum or other highly flammable liquids.
• Do not throw, drop or mishandle the unit.
• Do not disassemble, tamper with or modify the unit for any other purpose than that for which it was originally intended.
• Do not store either the unit or suction tubes near areas of high temperatures, direct sunlight, rain or snow.
• It is highly recommended that the unit be drained and cleaned after each use.
Owner’s MANUAL
9L Manual Fluid Extraction Pump
Prod. No. 350551
Mod. No. JMEP-9
1

www.jetgroupbrands.com
EXTRACTOR PARTS
Extractor Unit
Instruction Manual
Extracting Tube
Main Suction Tube
Tube Storage Unit
Brake Tube with
Rubber Fitting
2

www.jetgroupbrands.com
EXTRACTOR UNIT COMPONENTS
A. Housing Cover
B. Pressure Release Valve
C. Reservoir Tank
D. Tube Storage Unit
E. Footboard
F. Base
G. Hand Pump
H. Handle
I. Fluid Outlet Housing
J. Fluid Inlet Coupler
K. Fluid Inlet Tube
L. Extracting Tube
M. Brake Tube with Rubber Fitting
3

www.jetgroupbrands.com
OPERATING INSTRUCTIONS
Notes:
When using the Manual Fluid Extraction Pump to extract
engine oil, first you need to make sure the vehicle is
level, and then run the engine for about 5 minutes to
warm the oil and allow any sludge or contamination
within the oil to mix.
OPERATING STEPS:
1. Set up the Tube Storage Unit ( D ) into the two hooks of the Reservoir Tank ( C )
2. Remove the oil dipstick from the engine.
4

www.jetgroupbrands.com
3. Insert the Extracting Tube ( L ) into the dipstick
hole until it reaches the bottom of the oil pan.
Connect the Fluid Inlet Tube ( K ) into the Fluid
Inlet Coupler ( J ) with the Fluid Inlet Tube
Adapter.
The Fluid Inlet Tube ( K ) will connect to the
Extracting Tube ( L ) with the Extracting Tube
Adapter.
4. Lift the Handle ( H ) of the Hand Pump ( G )
to the top position and press it to the bottom
position repeatedly.
The Extraction Pump will start operating.
5. When the fluid inside the extractor tank reaches
"Full" position, the Extraction Pump will shut
off automatically, the Handle ( H ) of the Hand
Pump ( G ) wiII lock. Push the Pressure Release
Button ( B ) on the side of the Cover Housing
( A ), and then press the Handle ( H )of the
Hand Pump ( G ) to the bottom position to
release Hand Pump from locked position.
5

www.jetgroupbrands.com
6. Disconnect the Fluid Inlet Tube ( K ) and the
Extracting Tube ( L ), remove them from the
dipstick hole, open the Fluid Inlet Coupler ( J )
and dispose of the oil or fluid in accordance to
the laws and guidelines of your province.
6

www.jetgroupbrands.com
PARTS LIST
7

www.jetgroupbrands.com
PART LIST
Index Parts No. Description Unit
1 PX90M-01 Cover Housing 1
2 PX90-49 Release Button 1
3 PX90-49-1 Spring 1
4 PX90-06 Fluid Inlet Coupler 1
5 PX90-14 O Ring 25.2 x ø2.7mm 1
6 PX90-05 Fluid Outlet Housing 1
7 PX90-32 O Ring 31 x ø 1.0mm 1
8 PX90-09 Lock Nut 1
9 PX90-49-6 Locking Bushing 1
10 PX90-49-3 Shaft 1
11 PX90-49-5 Spring 1
12 PX90-51 Check Valve 1
13 PX90M-13 Safety Cup 1
14 PX90-49-5 Spring 1
15 PX90M-15 Bracket Base 1
16 PX90M-16 Arm 1
17 PX90-13 O Ring 154.3 x ø 3.5mm 1
18 PX90-02 Reservoir Tank 1
19 PX55-19 Pin 2
20 PX55-25 Screw ø 3.8 x 10mm 2
21 PX55-20 Float 1
22 PX90-04 Tube Storage Unit 1
23 PX90-03 Base 1
24 PX90-34 Screw ø 6 x 15mm 4
25 PX90-11 Footboard 1
Index Parts No. Description Unit
26 PX90-12 Fixed Strip 1
27 PX90-35 Screw ø 4 x 10mm 3
28 PX90-36 Screw M8 x 16mm 2
29 PX90M-29 Ring Seal 1
30 PX90-18 Shaft 1
31 PX90-28 Oil Seal 1
32 PX90-27 Holder 1
33 PX90-47 Flat Washer 2
34 PX90-46 Piston Spacer 1
35 PX90-45 Piston 1
36 PX90-44 Hex Nut M8 1
37 PX90-19 Holder 1
38 PX90M-17 Alum. Tube 1
39 PX90M-23 Alum. Tube Base 1
40 PX90-38 Screw M5 x 16mm 1
41 PX90-39 Nut M5 7
42 PX90-16 Handle 1
43 PX90-20 Cap 2
44 PX90-43 Screw M5 x 20mm 6
45 PX90-30 Main Suction Tube with Adapter 1
46 PX90-31 Extracting Tube with Adapter 1
47 PX90-68 Connecter 2
48 PX90-29 Brake Tube with Rubber Fitting 1
8