Jobsite LSC-6S Operation manual

INSTALLATION & USER GUIDE
.lnh5ile
PURE CUSTO~
For Stereo Music
Reproduction
from aSingle
In-Ceiling Location

l
-6
IN- NG LOUDSPEAKER
TABLE OF CONTENTS
Features 1
Product Overview 1
Package Contents 2
Preparing for Installation 2
Installation 11 •••••• 2
Operation 4
Specifications 4
warranty 5

FEATURES
6-1/2" mica filled polypropylene woofer with butyl rubber surround
Dual 3/4" stereo imaged liquid cooled polycarbonate dome tweeters
Moisture and UV resistant
Rust proof aluminum grille
Installation friendly design:
Suitable for painting
Connection terminals accepts up to 12 gauge speaker wire
Quick mounting system for new construction or retrofit
Includes hole template and paint mask
Ceiling Bracket for New Construction: Jobsite NCB-6 (sold separately)
PRODUCT OVERVIEW
The illustration shows how a
typical JobSite LSC loudspeaker
mounts into a ceiling.
Dogs swivel 90°, then
clamp the speaker frame
to the drywall.
Frames are molded with a
slight texture to assure good
paint adhesion.
Mounting screws tighten the
"dogs", clamping the speaker to
the drywall.
Ceiling Bracket serves as a "hole saver"
when drywall has not been applied.
Cannot use when installing loudspeaker in
existing ceilings.
Knockout wire tie allows the wire to be
secured to the bracket throughout the
new construction process. It knocks out
cleanly when the speaker is installed.
Wings instantly snap into
the bracket without screws.
Wings are scored for easy
size trimming.
Brackets and wings attach to
the ceiling joists with nails or
screws.
Rust-proof aluminum grilles make the loudspeaker
perfect for moist environments.
Figure 1
1

2
PACKAGE CONTENTS
Speakers x1
Speaker grille x1
Speaker hole template / paint mask x1
PREPARING FOR
INSTALLATION
If you are installing the LSC-6S into an
existing ceiling, take time to consider any
possible obstructions which may be hidden
inside the ceiling: ceiling joists, electrical
wiring, telephone wiring, plumbing, AC or
heating conduit and ductwork.
Determine the best mounting locations
based on the room layout. Before cutting
any holes, make sure the area behind the
speaker is clear for installation. Speakers
provide the best coverage, when centered
in the room. Line up the speaker with a
permanently mounted ceiling fixture such
as can lights, or a light fixture.
If you are installing the speaker into a new
ceiling follow the above recommendations
and install a JobSite NCB-6 Ceiling Bracket,
prior to the drywall being installed.
Run speaker wire from the speaker to the
amplifier location.
TOOLS REQUIRED
Stud Locator (for existing construction)
Drywall saw (for existing construction)
Pencil (for existing construction)
Cordless screwdriver with N02 Philips bit
Wire stripper
INSTALLATION
Installation Existing
Construction:
1. Use a stud locator to identify the location
of the ceiling joists on each side of the
proposed loudspeaker mounting location.
2. Mark ceiling joists' edges, using masking
tape.
3. You may have to adjust the loudspeaker
mounting location based on how the
ceiling joists line up with the proposed
speaker mounting location.
4. Check for clearance using the following
method:
a. Drill a 1/4" pilot hole in the center of the
intended speaker location.
b. Cut a foot-long piece of coat hanger.
c. Bend the wire, creating a right angle,
leaving 4-1/4" at one end.
d. Poke the ilL-shaped" wire into the pilot
hole and turn it in a complete circle,
checking for obstructions.
e. Push it up into the ceiling cavity to
make sure you have approximately
4" of depth.
f. If the coat hanger's movement is
obstructed by anything, fill the hole(s)
with spackle and try another location.
5. Locate the hole template and remove the
inside portion of it. The inside portion can
be used as a paint mask, if you are
painting the frame of the loudspeaker.
6. Use a pencil and hole template to trace
the hole outline in the desired location on
the ceiling.
7. Use a drywall saw to cut along the
penciled line.
8. Strip 1/4" of insulation from the end of
each wire coming from the amplifier.

9. lightly twist the end of each wire until no
frayed ends remain.
10. Attach the speaker wires to the speaker
terminal connectors. Connect the
negative output from the amplifier to the
black terminal and the positive output to
the red terminal.
11. There are four clamps "dogs" which
hold each speaker in place. Rotate all
the dogs inward.
12. Insert the loudspeaker into the cutout in
the ceiling.
13. The dogs are tightened via four
front-baffle screws. lighten the dogs
by turning the screws clockwise,
while pressing the loudspeaker against
the ceiling. NOTE: DO NOT OVER
TIGHTEN THESE SCREWS. Over-
tightening the screws may make the
grille difficult to install.
14. Install the grille into the speaker.
Installation New Construction:
Install the proper ceiling bracket for this
loudspeaker (NCB-6) using the instructions
supplied with the bracket. After the hole is
cut in the drywall per the bracket
instructions, perform the following steps:
1. Strip 1/4" of insulation from the end of
each wire coming from the amplifier.
2. lightlytwist the end of each wire until no
frayed ends remain.
3. Attach the speaker wires to the speaker
terminal connectors. Connect the
negative output from the amplifier to the
black terminal and the positive output
from the amplifier to the red terminal.
4. There are four clamps "dogs" which
hold each speaker in place. Rotate all
the dogs inward.
5. Insert the loudspeaker into the cutout in
the ceiling.
6. The dogs are tightened via four
front-baffle screws. lighten the dogs
by turning the screws clockwise,
while pressing the loudspeaker against
the ceiling. NOTE: DO NOT OVER
TIGHTEN THESE SCREWS. Over-
tightening the screws may make the grille
difficult to install.
8. Install the grille into the speaker.
Removing the Grilles:
To remove the grille from the LSC-6S, obtain
a small paper clip (size #1, common) and
bend the last quarter inch of it into an "L"
shape. Holding the paper clip with a pair of
pliers, insert the end with the ''L'' into a hole
near the edge of the grille. Stay near the
edge of the grille. Remove the grille by
pulling the paper clip towards you.
Painting the Speakers
The speakers must be masked prior to
painting them. The inside circular portion of
the hole template can be used as a paint
mask. Remove the outside portion of the
template by gently pulling along the
perforation. Affix the mask to the front of the
speaker using a piece of tape. Fold the tape
onto itself to form a double-sided loop. Affix
the tape to the tweeter and place the mask
onto the speaker.
3

4
Painting the Grilles
The LSC-6S grille should be painted before
it is installed on the speaker. The best
results will be obtained by using a spray
gun or airless sprayer. Thin the paint, and
then apply several light coats. This
technique helps prevent clogging of grille
holes. Paint both sides of the grille to cover
all the white paint.
OPERATION
Listening at Higher Volumes
It requires more power to achieve a
reasonable volume of sound in a large
room than it does in a small room. It is
possible to turn the volume so high that
the amplifier runs out of power. This creates
"clipping" distortion.
Clipping distortion makes treble sound very
harsh and unmusical. When you hear harsh
sounding treble from any good speaker,
turn the volume down immediately! You are
much less likely to damage a speaker
with a large amplifier because it will be
more difficult to produce clipping distortion.
SPECIFICATIONS
Power handing:
10 -100 watts
Frequency response:
60Hz-21kHz +/- 3dB
Impedance:
6 ohms
Dimensions:
9-1/4" outside diameter
8" diameter hole cutout
3-3/4" deep when installed in 1/2" drywall
Ceiling Bracket for New Construction:
JobSite NCB-6 (sold separately)
Warranty: 5 year limited

LIMITED WARRANTY
JobSite Systems ("JOBSITE''l, a Niles Audio
Corporation company, warrants its passive
products (those not requiring AC or battery
power) to the original purchaser to be free of
manufacturing defects in material and
workmanship for a period of ten years from date
of purchase.
JOBSITE warrants its passive loudspeaker
products (those not requiring AC or battery
power) to the original purchaser to be free of
manufacturing defects in material and
workmanship for a period of five years from date
of purchase.
JOBSITE warrants its indoor/outdoor
loudspeaker products to the original purchaser
to be free of manufacturing defects in material
and workmanship for a period of two years from
date of purchase.
JOBSITE warrants its all weather rock
loudspeaker products to the original purchaser
to be free of manufacturing defects in material
and workmanship for a period of five years from
date of purchase.
JOBSITE warrants its active products (those
requiring AC or battery power) to the original
purchaser to be free of ma nufacturing defects in
material and workmanship for a period of two
years from date of purchase.
This Warranty is subject to the following
additional conditions and limitations. The
Warranty is void and inapplicable if JOBSITE
deems that the product has been used or
handled other than in accordance with the
instructions provided by the manufacturer,
including, but not limited to, damage caused by
accident, mishandling, improper installation,
abuse, negligence, or normal wear and tear, or
any defect caused by repair to the product other
than by JOBSITE or an authorized JOBSITE
wholesale distributor.
To obtain warranty service, you must write to
JOBSITE: Include your name, address,
telephone number, model number and serial
number of your unit, and a brief description of
the problem.
A factory Return Authorization Number will be
sent to you. DO NOT RETURN ANY UNIT
WITHOUT FIRST RECEIVING WRITIEN
AUTHORIZATION AND SHIPPING
INSTRUCTIONS FROM JOBSITE.
If the above conditions are met, the purchaser's
sole remedy shall be to return the product to
JOBSITE, in which case JOBSITE will repair or
replace, at its sole option, the defective product
without charge for parts or labor. JOBSITE will
return the unit repaired or replaced under
warranty by shipping it by its usual shipping
method from the factory (only) at its expense
within the United States of America. THERE ARE
NO OTHER WARRANTIES, INCLUDING,
WITHOUT LIMITATION, EITHER EXPRESS OR
IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE,
WITH RESPECT TO THE PRODUCT.
REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER/PURCHASER.
JOBSITE SHALL NOT BE RESPONSIBLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES EXCEPT TO THE EXTENT PROVIDED
(OR PROHIBITED) BY APPLICABLE LAW.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation may not apply
to you. This warranty gives you specific legal
rights, and you may also have other rights,
which vary from state to state.
For the name of the nearest authorized JOBSITE
wholesale distributor, contact:
JobSite Systems, a Niles Audio
Corporation company
P.O. Box 160818, Miami, Florida 33116
5

./uh5ile
PURE CUSTO&t
JOBSITE SYSTEMS
12331 S.W. 130 STREET, MIAMI, FLORIDA 33186
P (866) 4JB-SITE (866-452-7483) - F [phone]
WWW.JOBSITESYSTEMS.COM
JobSite Systems, a Niles Audio Corporation company, 12331 S.w. 130 Street, Miami, FI 33186. ©2004 Niles Audio Corp.oration. JobSite, Pure
Custom and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logo is a trademark of Niles Audio Corporation. All other
trademarks are the property of their respective owners. Some JobSite products (or components thereof) are manufactured under one or more
U.S. Patents, foreign equivalents and/or pending patents (see product for details!. Because we constantly strive to improve our products, JobSite
reserves the right to change product specifications, descriptions, and prices without notice. The technical and other specificatiOfls of informa-
tion contained herein are not intended to set forth all technical and other specifications of JobSite products. Additional information can be
obtained at www.JobSitesystems.comorbycallingJobSiteat866-452-7483.PrintedinChina.11/04 DS00385ACN