John Lewis JLWM 1200 User manual

JLWM 1200
1200 spin washing machine
Instruction manual

Safety information
It is most important that this instruction book should be retained with
the appliance for future reference. Should the appliance be sold or
transferred to another owner, or should you move house and leave the
appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance
and the relevant warnings.
These warnings have been provided in the interest of safety. You MUST
read them carefully before installing or using the appliance. If you are
unsure of the meanings of these warnings contact the John Lewis branch
from which you purchased the appliance.
Important! Read carefully and keep for
future reference.
• The safety of your appliance complies with
the industry standards and with legal
requirements on the safety of appliances.
However, as manufacturers, we feel it is
our duty to provide the following safety
notes.
• It is most important that this instruction
book should be retained with the appliance
for future reference. Should the appliance
be sold or transferred to another owner,
or should you move house and leave the
appliance, always ensure that the book is
supplied with the appliance in order that the
new owner can get to know the functioning
of the appliance and the relevant warnings.
• You MUST read them carefully before
installing or using the appliance.
• Before first starting up, check the appliance
for any damage incurred during transport.
Never connect up a damaged appliance . If
parts are damaged, contact your supplier.
• If the appliance is delivered in the winter
months when there are minus
temperatures. Store it at room
temperature for 24 hours before using for
the first time.
General safety
• It is dangerous to alter the specifications or
attempt to modify this product in any way.
• During high temperature wash
programmes the door glass may get hot.
Do not touch it!
• Make sure that small children and animals
do not climb into the drum. To avoid this,
please check into the drum before using.
• Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp
material can cause extensive damage and
must not be placed into the machine.
• Only use the advised quantities of fabric
softener and detergent. Damage to the
fabric can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
• Wash small items such as socks, laces,
washable belts etc in a washing bag or
pillow case as it is possible for such items to
slip down between the tub and the inner
drum.
2

• Do not use your washing machine to wash
articles with whalebones, material without
hems or torn material.
• Always unplug the appliance and turn off
the water supply after use and during
cleaning and maintenance.
• Under no circumstances should you
attempt to repair the machine yourself.
Repairs carried out by inexperienced
people may cause injury or serious
malfunctioning. Contact your local Service
Centre. Always insist on genuine spare
parts.
Installation
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this
is not adhered to. See relevant section in
the user manual.
• After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable against the wall.
• If the machine is situated on a carpeted
floor, please adjust the feet in order to
allow air to circulate freely under the
appliance.
• Always be sure, that there is no water
leakage from hoses and their connections
after the installation.
• If the appliance is installed in a location
subject to frost, please read the “dangers of
freezing” chapter.
• Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
• Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
Use
• This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
• Only wash and dry fabrics which are
designed to be machine washed or dried.
Follow the instructions on each garment
label
• Do not overload the appliance. See the
Washing Programme Table.
• Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and
treat stains such as paint, ink, rust, and grass
before washing. Underwired bras must
NOT be machine washed.
• Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
• As some duvets and eiderdowns should be
washed/dried in large commercial
machines because of their bulk, please
check with the manufacturer of the item
before washing in a domestic machine.
• The users should always check that they
have not left their gas lighters (disposable
or otherwise) in their clothing.
• Never tumble dry items that have had
contact with chemicals such as dry cleaning
fluid. These are of a volatile nature and
could cause an explosion. Only tumble dry
items which have been washed in water or
require airing.
3

• Plastic detergent dispensers should not
remain in the drum during the drying cycle,
as the plastic used is not designed to
withstand the heat. If you wish to wash-
through-to-dry you should use the
conventional detergent dispenser drawer.
• Never pull the power supply cable to
remove the plug from the socket; always
take hold of the plug itself.
• Never use your new appliance if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the appliance is accessible.
Child safety
• This appliance is not intended for use by
person (including children) with reduced
physical sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
• The packaging components (e.g. plastic
film, polystyrene) can be dangerous to
children - danger of suffocation! Keep them
out of children’s reach.
• Keep all detergents in a safe place out of
children’s reach.
• Make sure that children or pets do not
climb into the drum. To prevent children
and pets becoming trapped inside the drum
the machine incorporates a special feature.
To activate this device, rotate the button
(without pressing it) inside the door
clockwise until the groove is horizontal. If
necessary use a coin.
To disable this device and restore the
possibility of closing the door, rotate the
button counterclockwise until the groove is
vertical.
4

Contents
Operating instructions
Safety information 2
General safety 2
Installation 3
Use 3
Child safety 4
Product description 6
Detergent dispenser drawer 7
Control panel 7
First use 9
Daily use 9
Load the laundry 9
Measure out the detergent 10
Select the required programme by turning the
programme selector dial 10
Select the spin speed or Rinse Hold option by
pressing button 3 11
Select the available options by pressing button
4 11
Start the programme by pressing button 5 11
Altering an option or a running programme 11
Interrupting a programme 12
Cancelling a programme 12
Opening the door 12
At the end of the programme 12
Helpful hints and tips 13
Washing Programmes 15
Technical data 17
Consumption values 17
Care and cleaning 18
Installation instructions
Installation 22
Unpacking 22
Positioning and levelling 23
Plumbing in 23
Water inlet 24
Water drainage 24
Special conditions 26
In the interest of the environment 26
Electrical connection 27
What to do if… 28
Repairs - After Sales Service 31
Environment concerns 32
Packaging materials 32
Ecological hints 32
Guide to use the
instruction manual
The following symbols will be found in the text
to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
5

Product description
1Detergent dispenser drawer
2Control panel
3Door opening handle
4Rating plate
5Drain pump
6Adjustable feet
1 2
3
5
4
6
6

Detergent dispenser drawer
Compartment for detergent used for
prewash and soak phase or for stain remover
used during the stain action phase (if
available). The prewash and soak detergent is
added at the beginning of the wash
programme. The stain remover is added
during the stain action phase.
Compartment for powder or liquid
detergent used for main wash. If using liquid
detergent pour it just before starting the
programme.
Compartment for liquid additives (fabric
softener, starch).
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the
detergent dispenser drawer. Any fabric
softener or starching additives must be
poured into the compartment before starting
the wash programme.
Control panel
Below is a picture of the control panel.
It shows the programme selector dial
as well as the buttons, pilot lights and
the display. These are presented by
relevant numbers on the following
pages.
7

1 2 3 4 5 6
1Detergent dispenser drawer
2Programme selector dial
3SPIN reduction button
4PREWASH and QUICK options
button
5START/PAUSE button
6Indicator pilot lights
Programme Selector Dial
It allows you to switch the appliance on/off
and/or to select a programme.
Available options:
Spin
By pressing this button you can change the
spin speed of the selected programme or to
select Rinse Hold option.
Rinse hold
By selecting this function the water of the last
rinse is not emptied out to prevent the fabrics
from creasing. Before opening the door it will
be necessary to empty out the water. To
empty out the water, please read the
paragraph «At the end of the programme».
Prewash
By selecting this option the machine performs
a prewash cycle before the main wash phase.
The washing time will be prolonged. This
option is recommended for heavily soiled
laundry.
Quick
This option can be used for lightly soiled
laundry. The washing time will be reduced
according to type of fabric and the selected
temperature.
Start Pause
This button allows you to start or to interrupt
the selected programme.
Indicator pilot light (6)
The light Wash illuminates after pressing
button 5.
The light Door lock indicates if the door can
be opened:
• The light is lit: the door cannot be opened.
• The light is out: the door can be opened.
• The light is flashing: the door is unlocking
and soon can be opened.
8

The light End illuminates at the end of the
washing cycle.
First use
• Ensure that the electrical and water
connections comply with the
installation instructions.
• Remove the polystyrene block and
any material from the drum.
• Pour 2 litres of water into the main
wash compartment of the
detergent drawer in order to
activate the ECO valve. Then run a
cotton cycle at the highest
temperature without any laundry in
the machine, to remove any
manufacturing residue from the
drum and tub. Pour 1/2 a measure
of detergent into the main wash
compartment and start the
machine.
Daily use
Load the laundry
Open the door by carefully pulling the door
handle outwards. Place the laundry in the
drum, one item at a time, shaking them out as
much as possible. Close the door.
9

Measure out the
detergent
Measure out the detergent and the
fabric softener
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent
required, pour it into the main wash
compartment or in the appropriate
compartment if it is required by the selected
programme or option (see more details in
«Detergent dispenser drawer» ).
If required, pour fabric softener into the
compartment marked (the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
Select the required
programme by turning
the programme selector
dial
Turn the programme selector dial to the
required programme. The washing machine
will automatically select the maximum spin
value provided for the programme you have
chosen. You can change this value by pressing
the corresponding button. The green pilot
light of the button 5starts to flash.
The selector dial can be turned either
clockwise or counterclockwise. Turn to
position « Off » to reset programme/
Switching the machine off.
At the end of the programme the
selector dial must be turned to
position «Off» , to switch the machine
off.
Caution! If you turn the programme
selector dial to another programme
when the machine is working, the red
pilot light of button 5will blink 3 times
to indicate a wrong selection. The
machine will not perform the new
selected programme.
10

Select the spin speed or
Rinse Hold option by
pressing button 3
The relevant light will light up.
When selecting a programme, the light
corresponding to the maximum speed
allowed for that programme will illuminate.
Select the available
options by pressing
button 4
Depending on the programme, different
functions can be combined. These must be
selected after choosing the desired
programme and before starting the
programme.
When these buttons are pressed, the
corresponding pilot lights illuminate. When
they are pressed again, the pilot lights go out.
If an incorrect option is selected, the
integrated red pilot light of the button 5
flashes for 3 times.
For the compatibility among the
washing programmes and the options
see chapter «Washing Programmes».
Start the programme by
pressing button 5
To start the selected programme, press the
button 5, the corresponding green pilot light
stops blinking. The pilot light Wash and
Door lock illuminate. The appliance starts
operating and the door is locked.
To interrupt a programme which is running,
press the button 5: the corresponding green
pilot light starts blinking.
To restart the programme from the point at
which it was interrupted, press the button 5
again .
If an incorrect option is selected, the red pilot
light of the button 5blinks 3 times.
Altering an option or a
running programme
It is possible to change some options before
the programme carries them out.
11

Before you make any change, you must
PAUSE the appliance by pressing the button
5.
Changing a running programme is possible
only by resetting it. Turn the programme
selector dial to Off and then to the new
programme position. Start the new
programme by pressing the button 5again.
The washing water in the tub will be not
emptied out.
Interrupting a
programme
Press the button 5to interrupt a programme
which is running, the corresponding green
pilot light starts blinking.
Press the button again to restart the
programme.
Cancelling a programme
Turn the selector dial to Off position to cancel
a programme which is running. Now you can
select a new programme.
Opening the door
After the programme has started the door is
locked. If, for any reason, you need to open
it, set firstly the machine to PAUSE by pressing
the button 5. After a few minutes the "Door
lock" light goes off and the door can be
opened.
If the door remains locked, this means that the
machine is already heating or that the water
level is too high. In any case, do not try to force
the door!
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to Off position. After
a few minutes the door can be opened (pay
attention to the water level and
temperature!) .
After closing the door, it is necessary to select
the programme and options again and to
press button 5.
At the end of the
programme
The machine stops automatically. The pilot
light of button 5goes off and after a few
minutes the Door lock pilot light goes off.
The light End illuminates. The door can be
opened.
If a programme or an option that ends with
water left in the tub has been selected, the
light Door lock illuminates and the door
remains locked to indicate that the water must
be emptied out before opening the door.
Follow the below instructions to empty out
the water:
1. Turn the programme selector dial to Off .
2. Select the draining or spinning
programme.
3. Reduce the spin speed if needed, by
pressing the relevant button.
4. Press button 5.
At the end of the programme, the door can
be now opened. Turn the programme
selector dial to Off to switch the machine off.
Remove the laundry from the drum and
carefully check that the drum is empty. If you
do not intend to carry out another wash, close
the water tap. Leave the door open to
prevent the formation of mildew and
unpleasant smells.
If your laundry is not removed during 10
minutes after the programme is finished the
energy saving system is enabled. All options
and cycle status pilot lights are turned off, only
the button 5pilot light is blinking to indicate
that the appliance has to be switched off. By
pressing any button the appliance will come
out from the energy saving status and you
12

Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each
garment label and the manufacturer’s washing
instructions. Sort the laundry as follows:
whites, coloureds, synthetics, delicates,
woollens.
Before loading the
laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Make sure that no metal objects are
left in the laundry (e.g. hair clips, safety
pins, pins).
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long
tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove
hooks or tie them up in a bag or net.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with
turpentine, lay the garment on a soft surface
and dab the stain with your fingertips and a
cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will already have been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone
1)
, lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above,
then treat stains with methylated spirits. Treat
any residual marks with bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone
1)
, then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment.
1) do not use acetone on artificial silk
13

Although biodegradable, detergents contain
substances which, in large quantities, can
upset the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washing machine
detergents may be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics
(60°C max) and woollens
• liquid detergents, preferably for low
temperature wash programmes (60°C
max) for all types of fabric, or special for
woollens only.
The detergent and any additives must be
placed in the appropriate compartments of
the dispenser drawer before starting the wash
programme.
If using liquid detergents, a programme
without prewash must be selected.
Your appliance incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the
detergent dispenser drawer .
Quantity of detergent to
be used
The type and quantity of detergent will
depend on the type of fabric, load size, degree
of soiling and hardness of the water used.
Follow the product manufacturers’
instructions on quantities to use.
Use less detergent if:
• you are washing a small load
• the laundry is lightly soiled
• large amounts of foam form during washing.
Degrees of water
hardness
Water hardness is classified in so-called
“degrees” of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company, or from your local authority. If the
water hardness degree is medium or high we
suggest you to add a water softener following
always the manufacturer’s instructions. When
the degree of hardness is soft, readjust the
quantity of the detergent.
14

Washing Programmes
Programme - Maximum and Minimum
Temperature - Cycle Description - Maximum
Spin Speed - Maximum Fabrics Load - Type of
Laundry
Options Detergent
Compartment
COTTONS
90° - 60°
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 5,5 kg - Reduced load 2,5 kg
White cotton (heavily or normally soiled items).
SPIN REDUCTION
RINSE HOLD
PREWASH
QUICK
1)
2)
COTTONS ECO
60°
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 5,5 kg
White or fast colour cotton (normally or slightly
soiled items).
This programme can be selected for slightly or normally
soiled cotton items. The temperature will decrease and
the washing time will be extended. This allows to obtain
a good washing efficiency by saving energy.
SPIN REDUCTION
RINSE HOLD
PREWASH
2)
COTTONS
60° - 40° - 30°
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 5,5 kg - Reduced load 2,5 kg
White and coloured cotton (normally soiled items).
SPIN REDUCTION
RINSE HOLD
PREWASH
QUICK
1)
2)
SYNTHETICS
60° - 40°
Main wash - Rinses
Maximum spin speed at 600 rpm
Max. load 3 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured
garments, non-shrink shirts, blouses.
RINSE HOLD
PREWASH
QUICK
1)
2)
DELICATES
40° - 30°
Main wash - Rinses
Maximum spin speed 600 rpm
Max. load kg 3 - Reduced load kg 1,5
Delicate fabrics: acrylics, viscose, polyester.
RINSE HOLD
PREWASH
QUICK
1)
2)
15

Programme - Maximum and Minimum
Temperature - Cycle Description - Maximum
Spin Speed - Maximum Fabrics Load - Type of
Laundry
Options Detergent
Compartment
WOOL
40°- 30°
Main wash - Rinses
Maximum spin speed at 600 rpm
Max. load 2 kg
Washing programme for machine washable wool as well
as for hand washable woollens and delicate fabrics.
Note : A single or bulky item may cause imbalance. If
the appliance doesn’t perform the final spin phase, add
more items, redistribute the load manually and then
select the spinning programme.
RINSE HOLD
RINSE
Rinses
Maximum spin speed at 1200 rpm
Max. load 5,5 kg
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand. The
machine performs 3 rinses, followed by a final long spin.
The spin speed can be reduced.
SPIN REDUCTION
RINSE HOLD
DRAIN
Draining of water
Max. load 5,5 kg
For emptying out the water of the last rinse in
programmes with the Rinse Hold option selected.
SPIN
Drain and long spin
Maximum spin speed at 1200 rpm
Max. load 5,5 kg
Separate spin for hand washed cotton garments and
after programmes with the Rinse Hold option selected.
You can choose the spin speed by pressing the relevant
button to adapt it to the fabrics to be spun.
SPIN REDUCTION
OFF
For cancelling the programme which is running or to switch the machine off .
1) If you select the Quick option by pressing button 4, we recommend that you reduce the maximum load as indicated.
Full loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergents, a programme without PREWASH must be selected.
16

Technical data
Dimensions Width
Height
Depth
Depth (Overall dimensions)
60 cm
85 cm
60 cm
63 cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate,
on the inner edge of the appliance door.
Water supply pressure Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load Cotton 5,5 kg
Spin Speed Maximum 1200 rpm
Consumption values
Programme Energy
consumption
(KWh)
Water consumption
(litres)
Programme
duration (Minutes)
White Cottons 90° 1,9 58 130
Cottons 60° 1.2 54 120
Cotton ECO 60°
1)
0,93 42 135
Cottons 40° 0.6 54 115
Synthetics 40° 0.5 50 80
Delicates 40° 0.55 50 65
Wool/ Handwash 30° 0.25 53 55
1) «Cottons Eco» at 60°C with a load of 5,5 kg is the reference programme for the data entered in the energy label,
in compliance with EEC 92/75 standards.
The consumption data shown on this
chart is to be considered purely
indicative, as it may vary depending on
the quantity and type of laundry, on the
inlet water temperature and on the
ambient temperature.
17

Care and cleaning
Warning! You must DISCONNECT
the appliance from the electricity
supply, before you can carry out any
cleaning or maintenance work.
Descaling
The water we use normally contains lime. It is
a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder
manufacturer's instructions. This will help to
prevent the formation of lime deposits.
After each wash
Leave the door open for a while. This helps to
prevent mould and stagnant smells forming
inside the appliance. Keeping the door open
after a wash will also help to preserve the door
seal.
Maintenance wash
With the use of low temperature washes it is
possible to get a build up of residues inside the
drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash programme.
• Use a normal measure of detergent, must
be a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance
with soap and water only, and then dry
thoroughly.
Cleaning the dispenser
drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
Remove the drawer by pressing the catch
downwards and by pulling it out. Flush it out
under a tap, to remove any traces of
accumulated powder.
To aid cleaning, the top part of the additive
compartment should be removed.
18

Cleaning the drawer
recess
Having removed the drawer, use a small brush
to clean the recess, ensuring that all washing
powder residue is removed from the upper
and lower part of the recess.
Replace the drawer and run the rinse
programme without any clothes in the drum.
Cleaning the pump
The pump should be inspected if:
• the machine does not empty and/or spin;
• the machine makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump.
Proceed as follows:
• disconnect the appliance;
• if necessary wait until the water has cooled
down.
• Open the pump door.
• Place a container close to the pump to
collect any spillage.
• Pull out the emergency emptying hose,
place it in the container and remove its cap.
• When no more water comes out, unscrew
the pump cover and remove it. Always
keep a rag nearby to dry up spillage of water
when removing the cover.
19

• Remove any objects from the pump
impeller by rotating it.
• Put the cap back on the emergency
emptying hose and place it back in its seat.
• Screw the pump cover fully in.
• Close the pump door.
Caution! When the appliance is in use
and depending on the programme
selected there can be hot water in the
pump.
Never remove the pump cover during
a wash cycle, always wait until the
appliance has finished the cycle, and is
empty. When replacing the cover,
ensure it is securely re-tightened so as
to stop leaks and young children being
able to remove it.
Cleaning the water inlet
filters
Warning! If the appliance doesn't fill
or it is taking longer to fill with water,
check if the water inlet filters are
blocked.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter using a hard bristle brush.
4. Screw the hose back onto the tap.
5. Unscrew the hose from the machine.
Keep a rug nearby because some water
may flow.
6. Clean the filter in the valve with a stiff
brush or with the piece of cloth.
7. Screw the hose back to the machine and
make sure the connection is tight.
8. Turn on the water tap.
20