Johnson controls Tm8e User manual

Johnson Controls Ducted Systems 5594752-UIM-C-1119

SINGLE STAGE ECM

RESIDENTIAL GAS FURNACES

MODELS: TM8E, TMLE

(80% Multi-Position/Standard & Low NOx)

INSTALLATION MANUAL

LIST OF SECTIONS

SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

GAS PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

ELECTRICAL POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

TWINNING AND STAGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

VENT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

START-UP AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . .16

SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

REPLACEMENT PART CONTACT INFORMATION . . . . . . . . . . . .25

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

START UP SHEET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

LIST OF FIGURES

Duct Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Furnace and Coil Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Combustible Floor Base Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Horizontal Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Typical Attic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Typical Suspended Furnace / Crawl Space Installation . . . . . . . . . . . 7

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Side Return Cutout Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Thermostat Chart - Single Stage AC with Single Stage Furnaces . .12

Thermostat Chart - Single Stage HP with Single Stage Furnaces . .12

Twinned Furnaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Combustion Air Inducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Combustion Airflow Path Through The

Furnace Casing to the Burner Compartment . . . . . . . . . . . . . . . . . .14

Ambient Combustion Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Reading Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Furnace Control Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

LIST OF TABLES

Unit Clearances to Combustibles (All Dimensions in Inches and cm, and

All Surfaces Identified with the Unit in an Upflow Configuration) . . . . 4

Cabinet and Duct Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Recommended Filter Sizes (High Velocity 600 FPM) . . . . . . . . . . . . 8

Nominal Manifold Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Ratings & Physical / Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . 11

Estimated Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Unconfined Space Minimum Area . . . . . . . . . . . . . . . . . . . . . . . . . .14

Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Gas Rate (CU FT/HR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Inlet Gas Pressure Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Nominal Manifold Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Default Blower Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Blower Performance CFM - Any Position (without filter) . . . . . . . . . .21

These high efficiency, compact units employ induced combustion, reli-

able hot surface ignition and high heat transfer aluminized tubular heat

exchangers. The units are factory shipped for installation in upflow or

horizontal applications and may be converted for downflow applica-

tions.

These furnaces are designed for residential installation in a basement,

closet, alcove, attic, recreation room or garage and are also ideal for

commercial applications. All units are factory assembled, wired and

tested to assure safe dependable and economical installation and oper-

ation.

These units are Category I listed and may be common vented with

another gas appliance as allowed by the National Fuel Gas Code.

SECTION I: SAFETY

This is a safety alert symbol. When you see this symbol on

labels or in manuals, be alert to the potential for personal

injury.

Understand and pay particular attention to the signal words DANGER,

WARNING, or CAUTION.

DANGER indicates an imminently hazardous situation, which, if not

avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation, which, if not

avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation, which, if not

avoided may result in minor or moderate injury. It is also used to

alert against unsafe practices and hazards involving only property dam-

age.

WARNING

Improper installation may create a condition where the operation of

the product could cause personal injury or property damage.

Improper installation, adjustment, alteration, service or maintenance

can cause injury or property damage. Failure to carefully read and

follow all instructions in this manual can result in furnace mal-

function, death, personal injury and/or property damage. Only a

qualified contractor, installer or service agency should install this

product.

5594752-UIM-C-1119

2 Johnson Controls Ducted Systems

SPECIFIC SAFETY RULES AND PRECAUTIONS

1. Only Natural gas or Propane (LP) gas are approved for use with

this furnace.

2. Install this furnace only in a location and position as specified in

these instructions.

3. A gas-fired furnace for installation in a residential garage must be

installed as specified in these instructions.

4. Provide adequate combustion and ventilation air to the furnace

space as specified in these instructions.

5. Combustion products must be discharged outdoors. Connect this

furnace to an approved vent system only, as specified in SECTION

VII of these instructions.

6. Test for gas leaks as specified in these instructions.

7. Always install the furnace to operate within the furnace’s intended

temperature rise range. Only connect the furnace to a duct system

which has an external static pressure within the allowable range, as

specified on the furnace rating plate.

8. When a furnace is installed so that supply ducts carry air circulated

by the furnace to areas outside the space containing the furnace,

the return air shall also be handled by duct(s) sealed to the furnace

casing and terminating outside the space containing the furnace.

9. It is permitted to use the furnace for heating of buildings or struc-

tures under construction where the application and use must com-

ply with all manufacturer’s installation instructions including:

• Proper vent installation;

• Furnace operating under thermostatic control;

• Return air duct sealed to the furnace;

• Air filters in place;

• Set furnace input rate and temperature rise per rating plate mark-

ing;

• Means for providing outdoor air required for combustion;

• Return air temperature maintained between 55ºF (13ºC) and

80ºF (27ºC);

• The air filter must be replaced upon substantial completion of

the construction process;

• Clean furnace, duct work and components upon substantial com-

pletion of the construction process, and verify furnace-operating

conditions including ignition, input rate, temperature rise and

venting, according to the manufacturer’s instructions.

10. When installed in a non-HUD-Approved Modular Home or building

constructed on-site, combustion air shall not be supplied from occu-

pied spaces.

11. The size of the unit should be based on an acceptable heat loss

calculation for the structure. ACCA, Manual J or other approved

methods may be used.

12. When moving or handling this furnace prior to installation it is rec-

ommended to leave the doors on the furnace to provide support

and to prevent damage or warping of the cabinet. When lifting the

furnace by the cabinet, support the ends of the furnace rather than

lifting by the cabinet flanges at the return air openings (bottom or

sides) or supply air opening.

13. When lifting the furnace, it is acceptable to use the primary heat

exchanger tubes as a lifting point provided that the tubes are lifted

at the front of the heat exchangers where attached to the vestibule

panel. Do not use the top return bend of the heat exchangers as lift-

ing points as the tubes may shift out of position or their location

brackets/baffles.

SAFETY REQUIREMENTS

• Refer to the unit rating plate for the furnace model number, and

then see the dimensions page of this instruction for return air ple-

num dimensions in Figure 7. The plenum must be installed

according to the instructions.

• Provide clearances from combustible materials as listed under

Clearances to Combustibles.

• Provide clearances for servicing ensuring that service access is

allowed for both the burners and blower.

• These models ARE NOT CSA listed or approved for installation

into a HUD Approved Modular Home or a Manufactured

(Mobile) Home.

• This furnace is not approved for installation in trailers or recre-

ational vehicles.

• Furnaces for installation on combustible flooring shall not be

installed directly on carpeting, tile or other combustible material

other than wood flooring.

• Check the rating plate and power supply to be sure that the elec-

trical characteristics match. All models use nominal 115 VAC, 1

Phase, 60 Hz power supply. DO NOT CONNECT THIS APPLI-

ANCE TO A 50 Hz POWER SUPPLY OR A VOLTAGE ABOVE

130 VOLTS.

• Furnace shall be installed so the electrical components are pro-

tected from water.

• Installing and servicing heating equipment can be hazardous due

to the electrical components and the gas fired components. Only

trained and qualified personnel should install, repair, or service

gas heating equipment. Untrained service personnel can perform

basic maintenance functions such as cleaning and replacing the

air filters. When working on heating equipment, observe precau-

tions in the manuals and on the labels attached to the unit and

other safety precautions that may apply.

COMBUSTION AIR QUALITY

(LIST OF CONTAMINANTS)

The furnace requires OUTDOOR AIR for combustion when the furnace

is located in any of the following environments.

• Restricted Environments

• Commercial buildings

• Buildings with indoor pools

• Furnaces installed in laundry rooms

• Furnaces installed in hobby or craft rooms

• Furnaces installed near chemical storage areas

• Chemical exposure

The furnace requires OUTDOOR AIR for combustion when the furnace

is located in an area where the furnace is being exposed to the follow-

ing substances and / or chemicals.

• Permanent wave solutions

• Chlorinated waxes and cleaners

• Chlorine based swimming pool chemicals

• Water softening chemicals

• De-icing salts or chemicals

• Carbon tetrachloride

• Halogen type refrigerants

• Cleaning solvents (such as perchloroethylene)

• Printing inks, paint removers, varnishes, etc.

• Hydrochloric acid

• Cements and glues

• Anti-static fabric softeners for clothes dryers

• Masonry acid washing materials

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow the safety warnings exactly could result in serious

injury, death or property damage.

Never test for gas leaks with an open flame. Use a commercially

available soap solution made specifically for detection of leaks to

check all connections. A fire or explosion may result causing property

damage, personal injury or loss of life.

IMPORTANT: During installation, doors should remain on the

furnace when moving or lifting.

CAUTION

This product must be installed in strict compliance with the installation

instructions and any applicable local, state, and national codes

including, but not limited to building, electrical, and mechanical codes.

5594752-UIM-C-1119

Johnson Controls Ducted Systems 3

When outdoor air is used for combustion, the combustion air intake duct

system termination must be located external to the building and in an

area where there will be no exposure to the substances listed above.

CODES AND STANDARDS

Follow all national, local codes and standards in addition to this installa-

tion manual. The installation must comply with regulations of the serv-

ing gas supplier, local building, heating, plumbing, and other codes. In

absence of local codes, the installation must comply with the national

codes listed below and all authorities having jurisdiction.

In the United States and Canada, follow all codes and standards for the

following, using the latest edition available:

STEP 1 -Safety

• US: National Fuel Gas Code (NFGC) NFPA 54/ANSI Z223.1 and

the Installation Standards, Warm Air Heating and Air Conditioning

Systems ANSI/NFPA 90B

• CANADA: CAN/CGA-B149.1 National Standard of Canada. Natu-

ral Gas and Propane Installation Codes (NSCNGPIC)

STEP 2 -General Installation

• US: Current edition of the NFGC and NFPA 90B. For copies, con-

tact the

National Fire Protection Association Inc.

Batterymarch Park

Quincy, MA 02269

or for only the NFGC, contact the

American Gas Association,

400 N. Capital, N.W.

Washington DC 20001

or www.NFPA.org

• CANADA: NSCNGPIC. For a copy contact:

Standard Sales, CSA International

178 Rexdale Boulevard

Etobicoke, (Toronto) Ontario Canada M9W 1RS

STEP 3 -Combustion and Ventilation Air

• US: Section 5.3 of the NFGC, air for Combustion and Ventilation

• CANADA: Part 7 of NSCNGPIC, Venting Systems and Air Supply

for Appliances

STEP 4 -Duct Systems

• US and CANADA: Air Conditioning Contractors Association

(ACCA) Manual D, Sheet Metal and Air Conditioning Contractors

Association National Association (SMACNA), or American Soci-

ety of Heating, Refrigeration, and Air Conditioning Engineers

(ASHRAE) 1997 Fundamentals Handbook Chapter 32.

STEP 5 -Acoustical Lining and Fibrous Glass Duct

• US and CANADA: Current edition of SMACNA and NFPA 90B as

tested by UL Standard 181 for Class IRigid Air Ducts

STEP 6 -Gas Piping and Gas Pipe Pressure Testing

• US: NFGC; chapters 2, 3, 4, & 9 and National Plumbing Codes

• CANADA: NSCNGPIC Part 5

STEP 7 -Electrical Connections

• US: National Electrical Code (NEC) ANSI/NFPA 70

• CANADA: Canadian Electrical Code CSA C22.1

These instructions cover minimum requirements and conform to exist-

ing national standards and safety codes. In some instances these

instructions exceed certain local codes and ordinances, especially

those who have not kept up with changing residential and non-HUD

modular home construction practices. These instructions are required

as a minimum for a safe installation.

WARNING

The furnace area must not be used as a broom closet or for any other

storage purposes, as a fire hazard may be created. Never store items

such as the following on, near or in contact with the furnace.

1. Spray or aerosol cans, rags, brooms, dust mops, vacuum clean-

ers or other cleaning tools.

2. Soap powders, bleaches, waxes or other cleaning compounds;

plastic items or containers; gasoline, kerosene, cigarette lighter

fluid, dry cleaning fluids or other volatile fluid.

3. Paint thinners and other painting compounds.

4. Paper bags, boxes or other paper products

Never operate the furnace with the blower door removed. To do

so could result in serious personal injury and/or equipment

damage.

FOR FURNACES INSTALLED IN THE COMMON-

WEALTH OF MASSACHUSETTS ONLY

For all side wall horizontally vented gas fueled equipment installed in

every dwelling, building or structure used in whole or in part for resi-

dential purposes, including those owned or operated by the Com-

monwealth and where the side wall exhaust vent termination is less

than seven (7) feet above finished grade in the area of the venting,

including but not limited to decks and porches, the following require-

ments shall be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At

the time of installation of the side wall horizontal vented gas

fueled equipment, the installing plumber or gasfitter shall

observe that a hard wired carbon monoxide detector with an

alarm and battery back-up is installed on the floor level where the

gas equipment is to be installed. In addition, the installing

plumber or gasfitter shall observe that a battery operated or hard

wired carbon monoxide detector with an alarm is installed on

each additional level of the dwelling, building or structure served

by the side wall horizontal vented gas fueled equipment. It shall

be the responsibility of the property owner to secure the services

of qualified licensed professionals for the installation of hard

wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled

equipment is installed in a crawl space or an attic, the hard

wired carbon monoxide detector with alarm and battery back-

up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not

be met at the time of completion of installation, the owner shall

have a period of thirty (30) days to comply with the above

requirements; provided, however, that during said thirty (30)

day period, a battery operated carbon monoxide detector with

an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon

monoxide detector as required in accordance with the above pro-

visions shall comply with NFPA 720 and be ANSI/UL 2034 listed

and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be perma-

nently mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with the

exhaust vent terminal for the horizontally vented gas fueled heat-

ing appliance or equipment. The sign shall read, in print size no

less than one-half (1/2) inch in size, "GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side wall

horizontally vented gas fueled equipment shall not approve the

installation unless, upon inspection, the inspector observes car-

bon monoxide detectors and signage installed in accordance

with the provisions of 248 CMR 5.08(2)(a)1 through 4.

5594752-UIM-C-1119

4 Johnson Controls Ducted Systems

INSPECTION

As soon as a unit is received, it should be inspected for possible dam-

age during transit. If damage is evident, the extent of the damage

should be noted on the carrier’s freight bill. A separate request for

inspection by the carrier’s agent should be made in writing. Also, before

installation, the unit should be checked for screws or bolts which may

have loosened in transit. There are no shipping or spacer brackets

which need to be removed from the interior of this unit.

FURNACE LOCATION AND CLEARANCES

The furnace shall be located using the following guidelines:

1. Where a minimum amount of air intake/vent piping and elbows will

be required.

2. As centralized with the air distribution as possible.

3. Where adequate combustion air will be available (particularly when

the appliance is not using outdoor combustion air).

4. Where it will not interfere with proper air circulation in the confined

space.

Installation in freezing temperatures:

1. Furnace shall be installed in an area where ventilation facilities pro-

vide for safe limits of ambient temperature under normal operating

conditions.

2. Do not allow return air temperature to be below 55ºF (13ºC) for

extended periods. To do so may cause condensation to occur in the

main heat exchanger, leading to premature heat exchanger failure.

Clearances for access/service:

Ample clearances should be provided to permit easy access to the unit.

The following minimum clearances are recommended:

1. Twenty-four (24) inches (61 cm) between the front of the furnace

and an adjacent wall or another appliance, when access is required

for servicing and cleaning.

2. Eighteen (18) inches (46 cm) at the side where access is required

for passage to the front when servicing or for inspection or replace-

ment of flue/vent connections.

In all cases, accessibility clearances shall take precedence over clear-

ances for combustible materials where accessibility clearances are

greater.

Installation in a residential garage:

A gas-fired furnace for installation in a residential garage must be

installed so the burner(s) and the ignition source are located not less

than 18” (46 cm) above the floor, and the furnace must be located or

protected to avoid physical damage by vehicles.

SECTION II: DUCTWORK

DUCTWORK GENERAL INFORMATION

The duct system’s design and installation must:

1. Handle an air volume appropriate for the served space and within

the operating parameters of the furnace specifications.

2. Be installed in accordance of National Fire Protection Association

as outlined in NFPA standard 90B (latest editions) or applicable

national, provincial, state, and local fire and safety codes.

3. Create a closed duct system. For residential and non-HUD Modular

Home installations, when a furnace is installed so that the supply

ducts carry air circulated by the furnace to areas outside the space

containing the furnace, the return air shall also be handled by a

duct(s) sealed to the furnace casing and terminating outside the

space containing the furnace.

4. Complete a path for heated or cooled air to circulate through the air

conditioning and heating equipment and to and from the condi-

tioned space.

When the furnace is used with an indoor coil, the coil must be installed

parallel with, or in the supply air side of the furnace to avoid condensa-

tion in the primary heat exchanger. When a parallel flow arrangement is

used, dampers or other means used to control airflow must be ade-

quate to prevent chilled air from entering the furnace. If manually oper-

ated, the damper must be equipped with means to prevent the furnace

or the air conditioner from operating unless the damper is in full heat or

cool position.

When replacing an existing furnace, if the existing plenum is not the

same size as the new furnace then the existing plenum must be

removed and a new plenum installed that is the proper size for the new

furnace. If the plenum is shorter than 12” (30.5 cm) the turbulent air flow

may cause the limit controls not to operate as designed, or the limit con-

trols may not operate at all.

The duct system is a very important part of the installation. If the duct

system is improperly sized the furnace will not operate properly.

The ducts attached to the furnace plenum, should be of sufficient size

so that the furnace operates at the specified external static pressure

and within the air temperature rise specified on the nameplate.

WARNING

Improper installation in an ambient below 32ºF (0ºC) could create a

hazard, resulting in damage, injury or death.

Table 1: Unit Clearances to Combustibles (All Dimensions in Inches and cm, and All Surfaces Identified with the Unit in an Upflow Configuration)

Application Top Front Rear Left

Side Right

Side Flue Floor/

Bottom Closet Alcove Attic Line

Contact

In. (cm) In. (cm) In. (cm) In. (cm) In. (cm) In. (cm)

Upflow 1 (2.5) 1 (2.5) 0 (0.0) 0 (0.0) 0 (0.0) 6 (15.2) Combustible Yes Yes Yes No

Upflow B-Vent 1 (2.5) 1 (2.5) 0 (0.0) 0 (0.0) 0 (0.0) 1 (2.5) Combustible Yes Yes Yes No

Downflow 1 (2.5) 1 (2.5) 0 (0.0) 0 (0.0) 0 (0.0) 6 (15.2) 1 (25.4)1

1. Special floor base or air conditioning coil required for use on combustible floor.

Yes Yes Yes No

Downflow B-Vent 1 (2.5) 1 (2.5) 0 (0.0) 0 (0.0) 0 (0.0) 1 (2.5) 1 (25.4)1Ye s Yes Ye s No

Horizontal 1 (2.5) 1 (2.5) 0 (0.0) 0 (0.0) 0 (0.0) 6 (15.2) Combustible No Yes Yes Yes2

2. Line contact only permitted between lines formed by the intersection of the rear panel and side panel (top in horizontal position) of the furnace jacket and building

joists, studs or framing.

Horizontal B-Vent 1 (2.5) 1 (2.5) 0 (0.0) 0 (0.0) 0 (0.0) 1 (2.5) Combustible No Yes Yes Yes2

CAUTION

The indoor coil must be installed in the supply air duct, downstream of

the furnace. Cooled air may not be passed over the heat exchanger.

!IMPORTANT: The minimum plenum height is 12” (30.5 cm). The fur-

nace will not operate properly on a shorter plenum height. The mini-

mum recommended rectangular duct height is 4” (10.1 cm) attached

to the plenum.

5594752-UIM-C-1119

Johnson Controls Ducted Systems 5

If a matching cased indoor coil is used, it may be placed directly on the

furnace outlet and sealed to prevent leakage. If an uncased indoor coil

with a thermoplastic drain pan is to be installed in the upflow/horizontal-

configuration, then extra 2” minimum spacing may be needed to ensure

against drain pan distortion.

On all installations without an indoor coil, a removable access panel is

recommended in the outlet duct such that smoke or reflected light

would be observable inside the casing to indicate the presence of leaks

in the heat exchanger. This access cover shall be attached in such a

manner as to prevent leaks.

DUCT FLANGES

Four flanges are provided to attach ductwork to the furnace. These

flanges are rotated down for shipment. In order to use the flanges,

remove the screw holding an individual flange, rotate the flange so it is

in the upward position and reinstall the screw then repeat this for all 4

flanges.

If the flanges are not used, they must remain in the rotated down posi-

tion as shipped.

DUCTWORK INSTALLATION AND SUPPLY PLENUM

CONNECTION - UPFLOW/HORIZONTAL

Attach the supply plenum to the furnace outlet. The use of

an approved flexible duct connector is recommended on all

installations. This connection should be sealed to prevent

air leakage. The sheet metal should be crosshatched to

eliminate any popping of the sheet metal when the indoor

fan is energized.

FLOOR BASE AND DUCTWORK INSTALLATION -

DOWNFLOW

Installations on combustible material or directly on any

floors must use a combustible floor base shown in Figure 3.

Follow the instructions supplied with the combustible floor

base accessory. This combustible floor base can be

replaced with a matching indoor coil, properly sealed to pre-

vent leaks. Follow the instructions supplied with the indoor

coil cabinet for installing the cabinet to the duct connector.

Plug intake and vent pipe holes in bottom panel and move

grommet to desired vent side exit.

Downflow Air Conditioning Coil Cabinet

The furnace should be installed with coil cabinet part number specifi-

cally intended for downflow application. If a matching indoor coil is

used, it may be placed directly on the furnace outlet and sealed to pre-

vent leakage. For details of the coil cabinet dimensions and installation

requirements, refer to the installation instructions supplied with the coil

cabinet.

Attach the indoor coil cabinet to the duct connector, and then position

the furnace on top of the coil cabinet. The connection to the furnace,

indoor coil cabinet, duct connector, and supply air duct must be sealed

to prevent air leakage.

COIL INSTALLATION

The indoor coil must be mounted on the supply side of the furnace as

shown in Figure 2. Refer to the Installation Instructions provided with

each indoor coil.

WARNING

The duct system must be properly sized to obtain the correct airflow

for the furnace size that is being installed.

Refer to Table 5 or the furnace rating plate for the correct rise range

and static pressures.

If the ducts are undersized, the result will be high duct static pres-

sures and/or high temperature rises which can result in a heat

exchanger OVERHEATING CONDITION. This condition can result in

premature heat exchanger failure, which can result in personal injury,

property damage, or death.

FIGURE 1: Duct Attachment

)DFWRU\

LQVWDOOHG

)RUGXFWDWWDFKPHQW

LIQHHGHG

$

IMPORTANT: On all installations without a coil, a removable access

panel is recommended in the outlet duct such that smoke or reflected

light would be observable inside the casing to indicate the presence

of leaks in the heat exchanger. This access cover shall be attached in

such a manner as to prevent leaks.

5594752-UIM-C-1119

6 Johnson Controls Ducted Systems

DOWNFLOW DUCT CONNECTORS

All downflow installations must use a suitable duct connector approved

by the furnace manufacturer for use with this furnace. The duct connec-

tors are designed to be connected to the rectangular duct under the

floor and sealed. Refer to the instructions supplied with the duct con-

nector for proper installation.

RESIDENTIAL AND MODULAR HOME UPFLOW

RETURN PLENUM CONNECTION

Return air may enter the furnace through the side(s) or bottom depend-

ing on the type of application. Return air may not be connected into the

rear panel of the unit.

SIDE RETURN APPLICATION

Side return applications pull return air through an opening cut in the

side of the furnace casing. This furnace is supplied with a bottom block-

off panel that should be left in place if a side return is to be used. If the

furnace is to be installed on a flat, solid surface, this bottom panel will

provide an adequate seal to prevent air leakage through the unused

bottom opening. However, if the furnace is to be installed on a surface

that is uneven, or if it is to be installed on blocks or otherwise raised off

the floor, it will be necessary to seal the edges of the bottom panel

to the casing using tape or other appropriate gasket material to

prevent air leakage.

BOTTOM RETURN AND ATTIC INSTALLATIONS

Bottom return applications normally pull return air through a base plat-

form or return air plenum. Be sure the return platform structure or return

air plenum is suitable to support the weight of the furnace.

The internal bottom panel must be removed for this application.

Attic installations must meet all minimum clearances to combustibles

and have floor support with required service accessibility.

DOWNFLOW APPLICATION

For downflow applications, the furnace must be turned upside-down so

that the circulating air enters at the top and exits the furnace at the bot-

tom. The combustion air inducer must be rotated 90° as shown in Fig-

ure 15. DO NOT BLOCK COMBUSTION AIR INLET OPENINGS.

FIGURE 2: Furnace and Coil Attachment

$

127(

9HULI\WKDWDOOGUDLQV

DUHWUDSSHGRUSOXJJHG

83)/2:

$33/,&$7,21

'2:1)/2:

$33/,&$7,21

35,0$5<'5$,1

75$3&211(&7,21

6(&21'$5<'5$,1

75$3&211(&7,21

'5$,13/8*

)25+25,=217$/

6(&21'$5<'5$,1

35,0$5<'5$,1

75$3&211(&7,21

&2,/

5,*+7)/2:

$33/,&$7,21

/()7)/2:

$33/,&$7,21

&2,/

'5$,13/8*

)259(57,&$/

6(&21'$5<'5$,1

)851$&(

FIGURE 3: Combustible Floor Base Accessory











)851$&(

:$50$,53/(180

:,7+´)/$1*(6

),%(5*/$66

,168/$7,21

),%(5*/$667$3(

81'(5)/$1*(

&20%867,%/()/225

%$6($&&(6625<

$

5594752-UIM-C-1119

Johnson Controls Ducted Systems 7

HORIZONTAL APPLICATION

ATTIC INSTALLATION

This appliance is certified for line contact when the furnace is installed

in the horizontal left or right position. The line contact is only permissible

between lines that are formed by the intersection of the top and two

sides of the furnace and the building joists, studs or framing. This line

may be in contact with combustible material. Refer to Figure 5.

When moving or handling this furnace prior to installation, always leave

the doors on the furnace to provide support and to prevent damage or

warping of the cabinet. When lifting the furnace, support the ends of the

furnace rather than lifting by the cabinet flanges at the return air open-

ings (bottom or sides) or supply air opening.

It is acceptable to use the primary heat exchanger tubes as a lifting

point provided that the tubes are lifted at the front of the heat exchang-

ers where attached to the vestibule panel. Do not use the top return

bend of the heat exchangers as lifting points as the tubes may shift out

of position or their location brackets/baffles.

SUSPENDED FURNACE / CRAWL SPACE

INSTALLATION

The furnace can be hung from floor joists or installed on suitable blocks

or pads. Blocks or pad installations shall provide adequate height to

ensure that the unit will not be subject to water damage.

Units may also be suspended from rafters or floor joists using rods, pipe

angle supports or straps. In all cases, the furnace should be supported

with rods, straps, or angle supports at three locations to properly sup-

port the furnace. Place one support at the supply end of the furnace,

one support located approximately in the center of the furnace near the

blower shelf, and the third support should be at the return end of the fur-

nace. Maintain a 6” (15.2 cm) minimum clearance between the front of

the furnace and the support rods or straps.

All six suspension points must be level to ensure proper and quiet fur-

nace operation. When suspending the furnace, use a secure platform

constructed of plywood or other building materials secured to the floor

or ceiling joists. Refer to Figure 6 for details and additional information.

When moving or handling this furnace prior to installation it is recom-

mended to leave the doors on the furnace to provide support and to

prevent damage or warping of the cabinet. When lifting the furnace,

support the ends of the furnace rather than lifting by the cabinet flanges

at the return air openings (bottom or sides) or supply air opening.

It is acceptable to use the primary heat exchanger tubes as a lifting

point provided that the tubes are lifted at the front of the heat exchang-

ers where attached to the vestibule panel. Do not use the top return

bend of the heat exchangers as lifting points as the tubes may shift out

of position or their location brackets/baffles.

FIGURE 4: Horizontal Application

IMPORTANT: This furnace may be installed in a horizontal position

on either side as shown above. It must not be installed on its back.

FIGURE 5: Typical Attic Installation

IMPORTANT: During installation, doors should remain on the

furnace when moving or lifting.

WARNING

When a furnace is installed in an attic or other insulated space, keep

all insulating materials at least 12 inches (30.5 cm) away from furnace

and burner combustion air openings.

$

  



5(7851$,5 6(',0(17

75$3

*$63,3,1*

6833/<$,5

9(170DLQWDLQ

UHTXLUHGFOHDUDQFHV

WRFRPEXVWLEOHV

/,1(&217$&721/<3(50,66,%/(

%(7:((1/,1(6)250('%<7+(

,17(56(&7,212))851$&(723

$1'7:26,'(6$1'%8,/',1*

-2,676678'625)5$0,1*

´

´0,1

:25.$5($

),/7(55$&.

0867%($0,1,080

',67$1&(

2)´FP

)5207+(

)851$&(

´

6+((70(7$/

,1)52172)

)851$&(

&20%867,21$,5

23(1,1*6,6

5(&200(1'('

$

FIGURE 6: Typical Suspended Furnace / Crawl Space Installation

IMPORTANT: During installation, doors should remain on the

furnace when moving or lifting.

6XSSRUW

5RG

6XSSRUW

$QJOH[ 0DLQWDLQ´PLQLPXP

FOHDUDQFHEHWZHHQVXSSRUW

URGVDQGIURQWRIIXUQDFH

$

5594752-UIM-C-1119

8 Johnson Controls Ducted Systems

SECTION III: FILTERS

FILTER INSTALLATION

All applications require the use of a field installed filter. All filters and

mounting provision must be field supplied.

Filters must be installed external to the furnace cabinet. DO NOT

attempt to install filters inside the furnace. 1. Air velocity through throwaway type filters may not exceed 300 feet per min-

ute (91.4 m/min). All velocities over this require the use of high velocity fil-

ters.

2. Do not exceed 1800 CFM using a single side return and a 16x25 filter. For

CFM greater than 1800, you may use two side returns or one side and the

bottom or one return with a transition to allow use of a 20x25 filter.

FIGURE 7: Dimensions

/()76,'( 5,*+76,'(

´

5(7851(1'

´

´

´

(OHFWULFDO

(QWU\

*DV3LSH

(QWU\

7KHUPRVWDW

:LULQJ

)5217

´

´

´

´

6833/<(1'

´

´

´

*DV3LSH

(QWU\

7KHUPRVWDW

:LULQJ

´

´

(OHFWULFDO

(QWU\

9HQW&RQQHFWLRQ

2XWOHW

9HQW

&RQQHFWLRQ

2XWOHW

´'LDPHWHU

9HQW&RQQHFWLRQ

2XWOHW

$

Table 2: Cabinet and Duct Dimensions

BTUH (kW)

Input Nominal

CFM (m3/min) Cabinet

Size Cabinet Dimensions (Inches) Approximate

Operating Weights

A A (cm) B B (cm) C C (cm) Lbs

40 (11.7) 1200 (34.0) A 14 1/2 36.8 13 3/8 34.0 10.3 26.2 89

60 (17.6) 1200 (34.0) A 14 1/2 36.8 13 3/8 34.0 10.3 26.2 94

80 (23.4) 1200 (34.0) B 17 1/2 44.4 16 3/8 41.6 11.8 29.9 103

80 (23.4) 1600 (45.3) C 21 53.3 19 7/8 50.5 13.6 34.5 116

80 (23.4) 2000 (56.6) C 21 53.3 19 7/8 50.5 13.6 34.5 121

100 (29.3) 1200 (34.0) B 17 1/2 44.4 16 3/8 41.6 11.8 29.9 108

100 (29.3) 1600 (45.3) C 21 53.3 19 7/8 50.5 13.6 34.5 120

100 (29.3) 2000 (56.6) C 21 53.3 19 7/8 50.5 13.6 34.5 124

120 (35.1) 1600 (45.3) C 21 53.3 19 7/8 50.5 15.8 40.1 125

120 (35.1) 2000 (56.6) C 21 53.3 19 7/8 50.5 15.8 40.1 131

130 (38.1) 2000 (56.6) D 24.5 62.2 23 3/8 59.4 17.5 44.4 137

CAUTION

All filters and mounting provision must be field supplied. All installa-

tions must have a filter installed.

NOTICE

Single side return above 1800 CFM is approved as long as the filter

velocity does not exceed filter manufacturer’s recommendation.

Table 3: Recommended Filter Sizes (High Velocity 600 FPM)

CFM

(m³/min) Cabinet

Size Side

(in) Bottom

(in)

1200 (34.0) A 16 x 25 14 x 25

1200 (34.0) B 16 x 25 16 x 25

1600 (45.3) C 16 x 25 20 x 25

2000 (56.6) C (2) 16 x 25 20 x 25

2000 (56.6) D (2) 16 x 25 22 x 25

5594752-UIM-C-1119

Johnson Controls Ducted Systems 9

SIDE RETURN

Locate the “L” shaped corner locators. These indicate the size of the cut-

out to be made in the furnace side panel. Refer to Figure 8.

Install the side filter rack following the instructions provided with that

accessory. If a filter(s) is provided at another location in the return air

system, the ductwork may be directly attached to the furnace side

panel.

HORIZONTAL FILTERS

Any branch duct (rectangular or round duct) attached to the plenum

must attach to the vertical plenum before the filter. Use of straps and/or

supports is required to support the weight of the external filter box.

DOWNFLOW FILTERS

Downflow furnaces typically are installed with the filters located above

the furnace, extending into the return air plenum or duct. Any branch

duct (rectangular or round duct) attached to the plenum must attach to

the vertical plenum above the filter height.

Filter(s) may be located in the duct system external to the furnace using

an external duct filter box attached to the furnace plenum or at the end

of the duct in a return filter grille(s). The use of straps and/or supports is

required to support the weight of the external filter box.

SECTION IV: GAS PIPING

GAS SAFETY

GAS PIPING INSTALLATION

Properly sized wrought iron, approved flexible or steel pipe must be

used when making gas connections to the unit. If local codes allow the

use of a flexible gas appliance connection, always use a new listed con-

nector. Do not use a connector that has previously serviced another gas

appliance.

Some utility companies or local codes require pipe sizes larger than the

minimum sizes listed in these instructions and in the codes. The furnace

rating plate and the instructions in this section specify the type of gas

approved for this furnace - only use those approved gases. The instal-

lation of a drip leg and ground union is required. Refer to Figure 10.

FIGURE 8: Side Return Cutout Markings

IMPORTANT: Some accessories such as electronic air cleaners and

pleated media may require a larger side opening. Follow the instruc-

tions supplied with that accessory for side opening requirements. Do

not cut the opening larger than the dimensions shown in Figure 7.

CAUTION

In downflow furnace arrangement, the filter must be located a mini-

mum of 12” from the return air inlet of furnace.

)52172)

)851$&(

&251(5

0$5.,1*6

6,'(2)

)851$&(

$

DANGER

An overpressure protection device, such as a pressure regulator,

must be installed in the gas piping system upstream of the furnace

and must act to limit the downstream pressure to the gas valve so it

does not exceed 0.5 PSI (14" w.c., 3.48 kPa). Pressures exceeding

0.5 PSI (14” w.c., 3.48 kPa) at the gas valve will cause damage to the

gas valve, resulting in a fire or explosion or cause damage to the fur-

nace or some of its components that will result in property damage

and loss of life.

FIGURE 9: Gas Valve

IMPORTANT: Plan your gas supply before determining the correct

gas pipe entry. Use 90-degree service elbow(s), or short nipples and

conventional 90-degree elbow(s) to enter through the cabinet access

holes.

INLET

WRENCH

BOSS

INLET

PRESSURE

PORT

OFF

ON/OFF SWITCH

(Shown in ON position)

MAIN REGULATOR

ADJUSTMENT

OUTLET

PRESSURE

PORT VENT PORT

A0226-001

FIGURE 10: Gas Piping

Upflow

Configuration

Downflow

Configuration

Horizontal

Configuration

External

Manual

Shut-off

Valve

External

Manual

Shut-off

Valve

External

Manual

Shut-off

Valve

To Gas

Supply

To Gas

Supply To Gas

Supply

To Gas

Supply

To Gas

Supply

To Gas

Supply

Drip

Leg

Drip

Leg Drip

Leg

Drip

Leg

Drip Leg

Gas

Valve

Gas

Pipe

Gas

Valve

GasPipe

Gas

Valve

Ground

Union

Ground

Union

Ground

Union

Ground

Union

Ground

Union

NOTE: Ground Union maybe installed inside or outside unit.

5594752-UIM-C-1119

10 Johnson Controls Ducted Systems

The furnace must be isolated from the gas supply piping system by

closing its individual external manual shutoff valve during any pressure

testing of the gas supply piping system at pressures equal to or less

than 1/2 psig (3.5 kPa).

Gas piping may be connected from either side of the furnace using any

of the gas pipe entry on both sides of the furnace. Refer to Figure 7.

GAS ORIFICE CONVERSION FOR PROPANE (LP)

This furnace is constructed at the factory for natural gas-fired operation,

but may be converted to operate on propane (LP) gas by using a fac-

tory-supplied LP conversion kit. Follow the instructions supplied with

the LP kit.

HIGH ALTITUDE GAS ORIFICE CONVERSION

This furnace is constructed at the factory for natural gas-fired operation

at 0 – 5,000 feet (0 – 1,524 m) above sea level.

The manifold pressure must be changed in order to maintain proper

and safe operation when the furnace is installed in a location where the

altitude is greater than 5,000 feet (1,524 m) above sea level. Refer to

Table 4 for proper manifold pressure settings.

HIGH ALTITUDE PRESSURE SWITCH CONVERSION

For installation where the altitude is less than 5,000 feet (1,524 m), it is

not required that the pressure switch be changed unless you are in an

area subject to low pressure inversions.

IMPORTANT: An accessible manual shutoff valve must be installed

upstream of the furnace gas controls and within 6 feet (1.8 m) of the

furnace.

CAUTION

The gas valve body is a very thin casting that cannot take any exter-

nal pressure. Never apply a pipe wrench to the body of the gas valve

when installing piping. A wrench must be placed on the octagon hub

located on the gas inlet side of the valve. Placing a wrench to the

body of the gas valve will damage the valve causing improper opera-

tion and/or the valve to leak.

WARNING

LoNOx furnaces requiring propane (LP) gas must have the LoNOx

screens removed prior to installation and operation. See propane

instructions.

Table 4: Nominal Manifold Pressure

Manifold Pressures (in w.c.) Manifold Pressures (kpa)

Altitude (feet) Altitude (m)

0-7999 8000-8999 9000-9999 0-2437 2438-2742 2743-3048

Gas Heating Value

(BTU/cu ft.)

800 3.5 3.5 3.5

Gas Heating Value

(MJ/cu m)

29.8 0.87 0.87 0.87

850 3.5 3.5 3.5 31.7 0.87 0.87 0.87

900 3.5 3.5 3.5 33.5 0.87 0.87 0.87

950 3.5 3.5 3.3 35.4 0.87 0.87 0.81

1000 3.5 3.2 2.9 37.3 0.87 0.80 0.73

1050 3.5 2.9 2.7 39.1 0.87 0.73 0.67

1100 3.2 2.7 2.4 41.0 0.80 0.66 0.61

2500 (LP) 9.8 8.2 7.5 93.2 (LP) 2.44 2.03 1.86

DANGER

PROPANE AND HIGH ALTITUDE CONVERSION KITS

It is very important to choose the correct kit and/or gas orifices for the altitude and the type of gas for which the furnace is being installed.

Only use natural gas in furnaces designed for natural gas. Only use propane (LP) gas for furnaces that have been properly converted to use pro-

pane (LP) gas. Do not use this furnace with butane gas.

Incorrect gas orifices or a furnace that has been improperly converted will create an extremely dangerous condition resulting in premature heat

exchanger failure, excessive sooting, high levels of carbon monoxide, personal injury, property damage, a fire hazard and/or death.

High altitude and propane (LP) conversions are required in order for the appliance to satisfactory meet the application.

An authorized distributor or dealer must make all gas conversions.

In Canada, a certified conversion station or other qualified agency, using factory specified and/or approved parts, must perform the conversion.

The installer must take every precaution to insure that the furnace has been converted to the proper gas orifice size when the furnace is installed.

Do not attempt to drill out any orifices to obtain the proper orifice size. Drilling out a gas orifice will cause misalignment of the burner flames, caus-

ing premature heat exchanger burnout, high levels of carbon monoxide, excessive sooting, a fire hazard, personal injury, property damage and/or

death.

5594752-UIM-C-1119

Johnson Controls Ducted Systems 11

SECTION V: ELECTRICAL POWER

ELECTRICAL POWER CONNECTIONS

Field wiring to the unit must be grounded. Electric wires that are field

installed shall conform to the temperature limitation for 63ºF (35ºC) rise

wire when installed in accordance with instructions. Refer to Table 5 in

these instructions for specific furnace electrical data.

The residential supply must have a bonded neutral.

Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures.

Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes.

The furnace shall be installed so that the electrical components are protected from water.

SUPPLY VOLTAGE CONNECTIONS

1. Provide a power supply separate from all other circuits. Install over-

current protection and disconnect switch per local/national electrical

codes. The switch should be close to the unit for convenience in

servicing. With the disconnect or fused switch in the OFF position,

check all wiring against the unit wiring label. Refer to the wiring dia-

gram in this instruction.

2. Remove the screws retaining the wiring box cover. Route the power

wiring through the opening in the unit into the junction box with a

conduit connector or other proper connection. In the junction box,

there will be a black wire and a white wire. Connect the power sup-

ply as shown on the unit-wiring label on the inside of the blower

compartment door or the wiring schematic in this section. The black

furnace lead must be connected to the L1 (hot) wire from the power

supply. The white furnace screw must be connected to neutral.

Connect the power supply ground to the green screw (equipment

ground) An alternate wiring method is to use a field provided 2” (5.1

cm) x 4” (10.1 cm) box and cover on the outside of the furnace.

Route the furnace leads into the box using a protective bushing

where the wires pass through the furnace panel. After making the

wiring connections replace the wiring box cover and screws. Refer

to Figure 11.

3. The furnace's control system requires correct polarity of the power

supply and a proper ground connection. Refer to Figure 11.

LOW VOLTAGE CONTROL WIRING CONNECTIONS

Install the field-supplied thermostat by following the instructions that

come with the thermostat. With the thermostat set in the OFF position

and the main electrical source disconnected, connect the thermostat

wiring from the wiring connections on the thermostat to the low voltage

terminal block on the integrated furnace control board, as shown in Fig-

ures 12 & 13. Electronic thermostats require the common wire to be

connected. Apply strain relief to thermostat wires passing through cabi-

net. If air conditioning equipment is installed, use thermostat wiring to

connect the Y and C terminals on the furnace control board to the

proper wires on the outdoor unit.

The 24-volt, 40 VA transformer is sized for the furnace components

only, and should not be connected to power auxiliary devices such as

humidifiers, air cleaners, etc. The transformer may provide power for a

split system air conditioner or heat pump.

CAUTION

Use copper conductors only.

Table 5: Ratings & Physical / Electrical Data

Input Output Nominal

Airflow AFUE Air Temp.

Rise

Max.

Outlet

Air Temp Blower Blower

Size

Recommended

Fuse or Circuit

Breaker Amps

Total

Unit

Amps

Gas Pipe

Connection,

NPT

MBH kW MBH kW CFM m3/min ºF ºC ºF ºC HP Amps

40 11.7 32 9.4 1200 34.0 80.0 20-50 11-28 190 88 1/2 6.4 11 x 8 15 8.2 1/2"

60 17.6 48 14.1 1200 34.0 80.0 30-60 17-33 190 88 1/2 6.4 11 x 8 15 8.2 1/2"

80 23.5 64 18.8 1200 34.0 80.0 35-65 19-36 190 88 1/2 6.4 11 x 8 15 8.7 1/2"

80 23.5 64 18.8 1600 45.3 80.0 30-60 17-33 190 88 1/2 8.8 11 x 10 15 8.7 1/2"

80 23.5 64 18.8 2000 56.6 80.0 25-55 14-31 190 88 1 11.5 11 x 11 20 13.8 1/2"

100 29.3 80 23.4 1200 34.0 80.0 40-70 22-39 190 88 1/2 6.4 11 x 8 15 8.7 1/2"

100 29.3 80 23.4 1600 45.3 80.0 40-70 22-39 190 88 3/4 8.8 11 x 10 15 11.1 1/2"

100 29.3 80 23.4 2000 56.6 80.0 25-55 14-31 190 88 1 11.5 11 x 11 20 13.8 1/2"

120 33.7 96 26.9 1600 45.3 80.0 40-70 22-39 190 88 3/4 8.8 11 x 10 15 11.1 1/2"

120 33.7 96 26.9 2000 56.6 80.0 35-65 19-36 190 88 1 11.5 11 x 11 20 13.7 1/2"

130 38.1 104 30.5 2000 56.6 80.0 35-65 19-36 190 88 1 11.5 11 x 11 20 13.7 1/2"

FIGURE 11: Electrical Wiring

Electrical Entry

Junction

Box

L1-Hot

Neutral

Connect ground

lead to screw

BLK

WHT

IMPORTANT: The power connection leads and wiring box may be

relocated to the left side of the furnace. Remove the screws and cut

wire tie holding excess wiring. Reposition on the left side of the fur-

nace and fasten using holes provided.

IMPORTANT: Set the heat anticipator in the room thermostat to 0.4

amps. Setting it lower will cause short cycles. Setting it higher will

cause the room temperature to exceed the set points.

IMPORTANT: Some electronic thermostats do not have adjustable

heat anticipators. They should be set to six cycles per hour. Follow

the thermostat manufacturer's instructions.

5594752-UIM-C-1119

12 Johnson Controls Ducted Systems

ACCESSORY CONNECTIONS

The furnace control will allow power-switching control of various acces-

sories.

ELECTRONIC AIR CLEANER CONNECTION

Two 1/4” (6.4 mm) spade terminals (EAC and NEUTRAL) for electronic

air cleaner connections are located on the control board. The terminals

provide 115VAC (1.0 Amp maximum) during circulating blower opera-

tion.

HUMIDIFIER CONNECTION

Two 1/4” (6.4 mm) spade terminals (HUM and NEUTRAL) for humidifier

connections are located on the control board. The terminals provide

115VAC (1.0 Amp maximum) during heating system operation.

A mounting hole is provided on the control panel next to the furnace

control board for mounting a humidifier transformer if required.

FIGURE 12: Thermostat Chart - Single Stage AC with Single Stage Furnaces

6LQJOH6WDJH$LU&RQGLWLRQHU±6LQJOH6WDJH)XUQDFH

<

)LUVW6WDJH

&RPSUHVVRU

:

6HFRQG6WDJH+HDW

)DQ

RU2

5HYHUVLQJ9DOYH

±9ROW+RW

:

)LUVW6WDJH+HDW

±9ROW&RPPRQ

±9ROW+RW

<

6HFRQG6WDJH

&RPSUHVVRU

<<

)XOO6WDJH&RPSUHVVRU

)DQ

6,1*/(67$*(

(&0)XUQDFH

6,1*/(67$*(

$,5

&21',7,21(5

±9ROW&RPPRQ

±9ROW+RW

<

&RPSUHVVRU&RQWDFWRU

)XOO6WDJH+HDW

<

)LUVW

6WDJH&RPSUHVVRU

7+(50267$7

$

FIGURE 13: Thermostat Chart - Single Stage HP with Single Stage Furnaces

$

6LQJOH6WDJH+HDW3XPS±6LQJOH6WDJH)XUQDFH

:

6HFRQG6WDJH+HDW

)DQ

±9ROW+RW

:

)LUVW6WDJH+HDW

±9ROW&RPPRQ

±9ROW+RW

<

6HFRQG6WDJH

&RPSUHVVRU

<<

)XOO6WDJH&RPSUHVVRU

)DQ

6,1*/(67$*(

(&0)XUQDFH

6,1*/(67$*(

+($73803

±9ROW&RPPRQ

±9ROW+RW

<

)LUVW6WDJH

&RPSUHVVRU

:

$X[LOLDU\+HDW

7+(50267$7

<

)LUVW6WDJH

&RPSUHVVRU

5HYHUVLQJ9DOYH

(QHUJL]HGLQ&RRO

RU2

5HYHUVLQJ9DOYH

<

)LUVW

6WDJH&RPSUHVVRU :2XW

::

)LUVW6WDJH+HDW

1RWH5RRPWKHUPRVWDW0867

FRQWUROIRVVLOIXHORSHUDWLRQ

5594752-UIM-C-1119

Johnson Controls Ducted Systems 13

SECTION VI: TWINNING AND STAGING

In applications where more heating capacity or more airflow capacity is

needed than what one furnace can deliver, twinning can be used to

make two furnaces operate in tandem (as long as the two furnaces

have the same model number). When two identical furnaces are

installed using the same duct system, it is very important that the two

furnace circulating air blowers operate simultaneously at all times. If

one blower starts before the second blower, the duct system will

become pressurized and the blower on the second furnace may turn

backwards causing the second furnace to overheat, resulting in dam-

age to the furnace. Twinning is used to make two furnaces operate in

tandem, using one duct system, one room thermostat and causing both

furnaces blowers to turn on and off simultaneously.

TWINNING DUCT SYSTEM

Twinned furnaces must only be applied on a common duct system. A

single air supply plenum must be used for both furnaces and indoor

coil(s). Separate plenums and supply ducts systems cannot be utilized.

A single return air plenum, common to both furnaces must be used. It is

suggested that a return platform be utilized, with bottom air entrance

into each furnace. If a side entrance return system is used, the common

return duct must be divided equally so as to supply each furnace with

an equal amount of return air.

Both furnaces must be identical models in both heating capacity and

CFM capacity. Both furnaces must be operated on the same motor

speed taps. Detailed and specific indoor blower motor wiring and con-

trol wiring information can be found in Source 1 twinning kit S1-

33103764000 installation instructions. See typical application, Figure

14.

If furnace staging is desired with two single stage furnaces on a com-

mon duct, where the gas burner on the first furnace operates on W1

and the gas burner on the second furnace operates on W2, then the

use of an air-mixing device in the plenum to mix the air from both fur-

naces is strongly recommended. The mixing device must be installed

before any ducts that supply air to occupied spaces. Twinning causes

both indoor fans to operate simultaneously. If a mixing device is not

used, any ducts that are connected down stream from the furnace that

is not operating in heat mode will be supplying cold air to the occupied

spaces.

SECTION VII: VENT SYSTEM

VENT CONNECTIONS

All models are provided with a flue transition that is sized for 4” diame-

ter vent connections. If a larger size vent connector is required, that

connection must be installed external to the furnace. Figure 15 shows

the furnace as it is shipped from the factory. To convert to a horizontal

or downflow position, remove the four screws that secure the inducer

assembly and rotate 90º being careful not to damage the gasket. Rein-

stall screws. Remove cap from appropriate vent outlet location on the

cabinet, cut insulation in cabinet to same size as the hole provided and

reinstall cap in the hole in the top panel.

CATEGORY 1 - 450 F. MAX. VENT TEMP.

The venting system must be installed in accordance with Section 5.3,

Air for Combustion and Ventilation, of the National Fuel Gas Code

Z223.1/NFPA 54 (latest edition), or Sections 7.2, 7.3 or 7.4 of CSA

B149.1, National Gas and Propane Codes (latest edition) or applicable

provisions of the local building code and these instructions.

The furnace shall be connected to any type of B, BW or L vent connec-

tor, and shall be connected to a factory-built or masonry chimney. The

furnace shall not be connected to a chimney flue serving a sepa-

rate appliance designed to burn solid fuel.

It is recommended that the appliance is installed in a location where the

space temperature is 32ºF (0ºC) or higher. If the appliance is installed in

a location where the ambient temperature is below 32ºF (0ºC), the com-

bustion byproducts could condense causing damage to the appliance

heat exchanger.

This appliance may be common vented with another gas appliance for

residential installations as allowed by the codes and standards listed in

these instructions.

Non-HUD approved Modular Homes must be vented with an approved

roof jack and may not be common vented with other appliances.

VENTING

Category I venting consists of vertically venting one or more appliances

in B-vent or masonry chimney (as allowed), using single wall metal pipe

or B-vent connectors. Type B-vent system extends in a general vertical

direction and does not contain offsets exceeding 45º. A vent system

having not more than one 60º offset is permitted.

NOTICE

For twinning applications, Source 1 twinning kit S1-33103764000

MUST be used.

FIGURE 14: Twinned Furnaces

$

CAUTION

If a return duct is connected to only one furnace (with a connection

between the two furnaces) an imbalance in the airflow will occur and

the furnace furthest from the return plenum will overheat.

IMPORTANT: In downflow applications, do not block the combustion

air inlet. The furnace must be installed on a coil cabinet or subbase to

allow combustion air to enter the burner compartment.

FIGURE 15: Combustion Air Inducer

COMBUSTION AIR INDUCER

90° 90°

Mounting Screw

(Remove)

Flue Transition

(Do Not Remove)

Mounting Screw

(Remove)

Pressure

Switch

Pressure Switch

Tube Routing

5594752-UIM-C-1119

14 Johnson Controls Ducted Systems

VENTING INTO AN EXISTING CHIMNEY

For Category I installations, the furnace shall be connected to a factory

built chimney or vent complying with a recognized standard, or a

masonry or concrete chimney lined with a material acceptable to the

authority having jurisdiction. Venting into an unlined masonry chimney

or concrete chimney is prohibited.

Where use of an existing chimney is unavoidable, the following rules

must be followed:

1. The masonry chimney must be built and installed in accordance

with nationally recognized building codes or standards and must be

lined with approved fire clay tile flue liners or other approved liner

material that will resist corrosion, softening, or cracking from flue

gases. THIS FURNACE IS NOT TO BE VENTED INTO AN

UNLINED MASONRY CHIMNEY.

2. This furnace must be vented into a fire clay tile lined masonry chim-

ney only if a source of dilution air is provided, such as by common

venting with a draft hood equipped water heater. If no source of

dilution air is available, Type B vent must be used, or masonry

chimney vent kit S1-1CK0604 must be used. Refer to the instruc-

tions with the kit to properly apply these masonry chimney kits.

3. The chimney must extend at least 3 ft (91 cm) above the highest

point where it passes through a roof of a building and at least two

feet higher than any portion of the building with a horizontal dis-

tance of ten feet.

4. The chimney must extend at least 5 ft (1.5 m) above the highest

equipment draft hood or flue collar.

FAN-ASSISTED COMBUSTION SYSTEM

This appliance is equipped with an integral mechanical means to either

draw products of combustion through the heat exchanger.

Ambient Combustion Air Supply

This type installation will draw the air required for combustion from

within the space surrounding the appliance and from areas or rooms

adjacent to the space surrounding the appliance. This may be from

within the space in a non-confined location or it may be brought into the

furnace area from outdoors through permanent openings or ducts. A

single, properly sized pipe from the furnace vent connector to the out-

doors must be provided. Combustion air is brought into the furnace

through the unit top panel opening.

An unconfined space is not less than 50 cu.ft (1.42 m3) per 1,000 Btu/

hr (0.2928 kW) input rating for all of the appliances installed in that

area.

Rooms communicating directly with the space containing the appli-

ances are considered part of the unconfined space, if doors are fur-

nished with openings or louvers.

A confined space is an area with less than 50 cu.ft (1.42 m3) per 1,000

Btu/hr (0.2928 kW) input rating for all of the appliances installed in that

area. The following must be considered to obtain proper air for combus-

tion and ventilation in confined spaces.

Combustion Air Source From Outdoors

The blocking effects of louvers, grilles and screens must be given con-

sideration in calculating free area. If the free area of a specific louver or

grille is not known, refer to Table 6, to estimate free area.

* Do not use less than 1/4” (6.4 mm) mesh

+ Free area of louvers and grille varies widely; the installer should follow

louver or grille manufacturer’s instructions.

Dampers, Louvers and Grilles (Canada Only)

1. The free area of a supply air opening shall be calculated by sub-

tracting the blockage area of all fixed louvers grilles or screens from

the gross area of the opening.

2. Apertures in a fixed louver, a grille, or screen shall have no dimen-

sion smaller than 1/4” (6.4 mm).

3. A manually operated damper or manually adjustable louvers are

not permitted for use.

4. A automatically operated damper or automatically adjustable lou-

vers shall be interlocked so that the main burner cannot operate

unless either the damper or the louver is in the fully open position.

FIGURE 16: Combustion Airflow Path Through The Furnace Casing to

the Burner Compartment

WARNING

This type of installation requires that the supply air to the appliance(s)

be of a sufficient amount to support all of the appliance(s) in the area.

Operation of a mechanical exhaust, such as an exhaust fan, kitchen

ventilation system, clothes dryer or fireplace may create conditions

requiring special attention to avoid unsatisfactory operation of gas

appliances. A venting problem or a lack of supply air will result in a

hazardous condition, which can cause the appliance to soot and gen-

erate dangerous levels of CARBON MONOXIDE, which can lead to

serious injury, property damage and / or death.

COMBUSTION

AIR

Table 6: Estimated Free Area

Wood or Metal

Louvers or Grilles

Wood 20-25%*

Metal 60-70% *

Screens+ 1/4” (0.635 cm)

mesh or larger 100%

WARNING

When a Category I furnace is removed or replaced, the original vent-

ing system may no longer be correctly sized to properly vent the

attached appliances.

An improperly sized vent system can cause CARBON MONOXIDE to

spill into the living space causing personal injury, and or death.

Table 7: Unconfined Space Minimum Area

BTUH Input Rating Minimum Free Area

Required for Each Opening

40,000 40 in2(258 cm2)

60,000 60 in2(387 cm2)

80,000 80 in2(516 cm2)

100,000 100 in2(645 cm2)

120,000 120 in2(742 cm2)

130,000 130 in2(838 cm2)

Table 8: Free Area

BTUH Input

Rating

Minimum Free Area Required for Each Opening

Horizontal Duct

(2,000 BTUH)

Vertical Duct or

Opening to Outside

(4,000 BTUH)

Round Duct

(4,000 BTUH)

40,000 20 in2(129 cm2) 10 in2(64 cm2)4” (10 cm)

60,000 30 in2(193 cm2) 15 in2(97 cm2)5” (13 cm)

80,000 40 in2(258 cm2) 20 in2(129 cm2)5” (13 cm)

100,000 50 in2(322 cm2) 25 in2 (161 cm2)6” (15 cm)

120,000 60 in2(387 cm2) 30 in2(193 cm2)7” (18 cm)

130,000 65 in2(419 cm2) 33 in2(213 cm2)7” (18 cm)

EXAMPLE: Determining Free Area.

Appliance 1 Appliance 2 Total Input

100,000 + 30,000 = (130,000 4,000) = 32.5 Sq. In. Vertical

Appliance 1 Appliance 2 Total Input

100,000 + 30,000 = (130,000 2,000) = 65 Sq. In. Horizontal

5594752-UIM-C-1119

Johnson Controls Ducted Systems 15

Air Supply Openings and Ducts

1. An opening may be used in lieu of a duct to provide the outside air

supply to an appliance unless otherwise permitted by the authority

having jurisdiction. The opening shall be located within 12” (30.5

cm) horizontally from, the burner level of the appliance. Refer to

“COMBUSTION AIR SOURCE FROM OUTDOORS and VENT

AND SUPPLY AIR SAFETY CHECK” in these instructions for addi-

tional information and safety check procedure.

2. The duct shall be either metal, or a material meeting the class 1

requirements of CAN4-S110 Standard for Air Ducts.

3. The duct shall be least the same cross-sectional area as the free

area of the air supply inlet opening to which it connects.

4. The duct shall terminate within 12” (30.5 cm) above, and within 24”

(61 cm) horizontally from, the burner level of the appliance having

the largest input.

5. A square or rectangular shaped duct shall only be used when the

required free area of the supply opening is 9 in2(58.06 cm2) or

larger. When a square or rectangular duct is used, its small dimen-

sion shall not be less than 3” (7.6 cm).

6. An air inlet supply from outdoors shall be equipped with a means to

prevent the direct entry of rain and wind. Such means shall not

reduce the required free area of the air supply opening.

7. An air supply inlet opening from the outdoors shall be located not

less than 12” (30.5 cm) above the outside grade level.

Combustion Air Source from Outdoors

1. Two permanent openings, one within 12” (30.5 mm) of the top and

one within 12” (30.5 mm) of bottom of the confined space, Two per-

manent openings, shall communicate directly or by means of ducts

with the outdoors, crawl spaces or attic spaces.

2. One permanent openings, commencing within 12” (30.5 cm) of the

top of the enclosure shall be permitted where the equipment has

clearances of at least 1” (2.54 cm) from the sides and back and 6”

(15.24 cm) from the front of the appliance. The opening shall com-

municate directly with the outdoors and shall have a minimum free

area of:

a. 1 in.2/ 3,000 BTU/hr (700mm2/kW) of the total input rating of all

equipment located in the enclosure.

b. Not less than the sum of all vent connectors in the confined

space.

3. The duct shall be least the same cross-sectional area as the free

area of the air supply inlet opening to which it connects.

4. The blocking effects of louvers, grilles and screens must be given

consideration in calculating free area. If the free area of a specific

louver or grille is not known. Refer to Table 6 to estimate free area.

Ventilated Combustion Air

The ventilated attic space or a crawl space from which the combustion

air is taken must comply with the requirements specified in “AIR

SOURCE FROM OUTDOORS” in this instruction or in Section 5.3, Air

for Combustion and Ventilation of the National Fuel Gas Code, ANSI

Z223.1 (latest edition). This type installation requires two properly sized

pipes. One brings combustion air from a properly ventilated attic space

or crawl space and a second pipe that extends from the furnace vent

connection (top right of unit) to the exterior of the building.

Vent and Supply (Outside) Air Safety Check Procedure

For Category I furnaces, vent installations shall be in accordance with

Parts 7 and 11 of the National Fuel Gas Code, ANSI Z223.1/NFPA 54,

and or Section 7 and Appendix B of the CSA B149.1, Natural Gas and

Propane Installation Codes, the local building codes, furnace and vent

manufacturer's instructions.

Multi-story or common venting systems are permitted and must be

installed in accordance with the National Fuel Gas Code, ANSI Z223.1/

NFPA 54 and / or the CSA B149.1, Natural Gas and Propane Installa-

tion Codes, local codes, and the manufacture's instructions.

Vent connectors serving Category I furnaces shall not be connected

into any portion of mechanical draft systems operating under positive

pressure.

Horizontal portions of the venting system shall be supported to prevent

sagging using hangers or perforated straps and must slope upwards

not less than 1/4” per foot (21 mm/m) from the furnace to the vent termi-

nal.

It is recommended that you follow the venting safety procedure below.

This procedure is designed to detect an inadequate ventilation system

that can cause the appliances in the area to operate improperly causing

unsafe levels of Carbon Monoxide or an unsafe condition to occur.

FIGURE 17: Ambient Combustion Air

*DEOH

9HQW

*DV

9HQW

6RIILW

9HQW

9HQWLODWHG

$WWLF

7RS$ERYH

,QVXODWLRQ

2SWLRQDO

,QOHWD

2XWOHW

$LUD

9HQWLODWHG

&UDZO6SDFH

*DV

:DWHU

+HDWHU

)XUQDFH

6RIILW

9HQW

*DV

:DWHU

+HDWHU ,QOHW

$LUD

,QOHW

$LUE

)XUQDFH

*DV

9HQW

2XWOHW

$LUD

2XWOHW

$LUE

,QOHW

$LUD

,QOHW

$LUE

*DV

:DWHU

+HDWHU

)XUQDFH

*DEOH

9HQW

*DV

9HQW

9HQWLODWHG

$WWLF

7RS$ERYH

,QVXODWLRQ

$

5594752-UIM-C-1119

16 Johnson Controls Ducted Systems

SECTION VIII: START-UP AND

ADJUSTMENTS

The following start-up checks MUST be performed by the furnace

installer on every new furnace installation.

1. Gas piping leak check.

2. Furnace input rate check.

3. Air temperature rise check.

Instructions on how to perform each of these required installation

checks are listed in the section “NOx SCREEN REMOVAL (Lo-NOx

Models Only)”.

When the gas supply is initially connected to the furnace, the gas piping

may be full of air. In order to purge this air, it is recommended that the

ground union be loosened until the odor of gas is detected. When gas is

detected, immediately retighten the union and check for leaks. Allow

five minutes for any gas to dissipate before continuing with the start-up

procedure. Be sure proper ventilation is available to dilute and carry

away any vented gas.

NOx SCREEN REMOVAL (Lo-NOx Models Only)

If the furnace is equipped with NOx screens and is to be used with LP

(propane) gas, the screens must be removed prior to start-up.

1. Make sure that the electrical power to the unit is turned off and that

the gas supply is turned off at the shut-off valve.

2. Remove the blower compartment and burner compartment access

doors.

3. Disconnect the gas supply piping at the union to permit removal of

the entire burner and gas control assembly from the vestibule

panel. Use the wrench boss on the gas valve when removing or

installing the piping.

4. Unplug the igniter from the wire harness. Disconnect the flame sen-

sor wires located on top of the air shield. Unplug the gas valve from

the wiring harness.

5. Remove the screws holding the burner assembly to the vestibule

panel.

6. Remove the burner assembly. It should be possible to swing the

burner assembly out of the way without disconnecting the remain-

ing wires.

7. With the burner assembly out of the way, simply slide the NOx

screens out of the heat exchanger tubes and discard the screens.

8. Replace all components in reverse order. Reconnect all wiring.

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each appliance connected to the venting system being placed into operation could result in carbon-

monxide poisoning or death.

The following steps shall be followed for each appliance connected to the venting system being placed into operation, while all other appliances

connected to the venting system are not in operation:

1. Inspect the venting system for proper size and horizontal pitch. Determine that there is no blockage, restriction, leakage, corrosion or other defi-

ciencies, which could cause an unsafe condition

2. Close all building doors and windows.

3. Turn on clothes dryers and TURN ON any exhaust fans, such as range hoods and bathroom exhausts, so they shall operate at maximum

speed. Open the fireplace dampers. Do not operate a summer exhaust fan.

4. Follow the lighting instructions. Place the appliance being inspected in operation. Adjust thermostat so the appliance shall operate continu-

ously.

5. Test each appliance (such as a water heater) equipped with a draft hood for spillage (down-draft or no draft) at the draft hood relief opening

after 5 minutes of main burner operation. Appliances that do not have draft hoods need to be checked at the vent pipe as close to the appliance

as possible. Use a combustion analyzer to check the CO2and CO levels of each appliance. Use a draft gauge to check for a downdraft or inad-

equate draft condition.

6. After it has been determined that each appliance properly vents when tested as outlined above, return doors, windows, exhaust fans, fireplace

dampers and any other gas burning appliance to their normal condition.

7. If improper venting is observed during any of the above tests, a problem exists with either the venting system or the appliance does not have

enough combustion air (Supply Air from outside) to complete combustion. This condition must be corrected before the appliance can function

safely.

NOTE: An unsafe condition exists when the CO reading exceeds 40 ppm and the draft reading is not in excess of - 0.1” w.c. (-25 kPa) with all

of the appliance(s) operating at the same time.

8. Any corrections to the venting system and / or to the supply (outside) air system must be in accordance with the National Fuel Gas Code

Z223.1 or CAN/CGA B149.1 Natural Gas and Propane Installation Code (latest editions). If the vent system must be resized, follow the appro-

priate tables in Appendix G of the above codes or for this appliance.

IMPORTANT: All electrical connections made in the field and in the

factory should be checked for proper tightness.

5594752-UIM-C-1119

Johnson Controls Ducted Systems 17

GAS PIPING LEAK CHECK

It is recommended that when the gas supply is first connected to the

furnace, the ground union be loosened until the odor of gas is detected.

When gas is detected, immediately tighten the union and check for gas

leaks. Allow five minutes for any gas to dissipate before continuing with

the start-up procedure. Be sure that proper ventilation is available to

dilute and carry away any vented gas.

With furnace in operation, check all of the pipe joints, gas valve connec-

tions and manual valve connections for leakage using an approved gas

detector, a non-corrosive leak detection fluid or other leak detection

methods. Take appropriate action to stop any leak. If a leak persists,

replace the faulty component.

The furnace and its equipment shut-off valve must be disconnected

from the gas supply during any pressure testing of that system at test

pressures in excess of 1/2” psig (3.45 kPa).

The furnace must be isolated from the gas supply piping system by

closing the equipment shut-off valve during any pressure testing of the

gas supply system.

IGNITION SYSTEM SEQUENCE

1. Turn the gas supply ON at external valve and main gas valve.

2. Set the thermostat above room temperature to call for heat.

3. System start-up will occur as follows:

a. The induced draft blower motor will start and come up to speed.

Shortly after inducer start-up, the hot surface igniter will glow for

about 17 seconds.

b. After this warm up, the ignition module will energize (open) the

main gas valve.

c. After flame is established, the supply air blower will start in about

30 seconds.

With furnace in operation, check all of the pipe joints, gas valve connec-

tions and manual valve connections for leakage using an approved gas

detector, a non-corrosive leak detection fluid, or other leak detection

methods. Take appropriate steps to stop any leak. If a leak persists,

replace the component.

CALCULATING THE FURNACE INPUT

(NATURAL GAS)

Verify natural gas input rate by clocking meter.

1. Turn off all other gas appliances and pilots.

2. Run furnace for a minimum of 3 minutes in heating operation.

3. Measure time (in sec) for gas meter to complete 1 revolution and

note reading. The 2 cubic feet dial provides a more accurate mea-

surement of gas flow.

4. Refer to Table 9 for cubic feet of gas per hour.

5. Multiply cubic feet per hour by heating value (BTU/cu. ft.) to obtain

input.

If clocked rate does not match the input rate from the unit nameplate.

follow steps in next section to adjust the manifold pressure. Repeat

steps 2 - 5 until correct input is achieved.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow the safety warnings exactly could result in serious

injury, death or property damage.

Never test for gas leaks with an open flame. Use a commercially

available soap solution made specifically for the detection of leaks to

check all connections. A fire or explosion may result causing property

damage, personal injury or loss of life.

IMPORTANT: Burner ignition may not be satisfactory on first startup

due to residual air in the gas line or until gas manifold pressure is

adjusted. The ignition control will make three attempts to light before

locking out.

IMPORTANT: Burner ignition may not be satisfactory on first startup

due to residual air in the gas line or until gas manifold pressure is

adjusted. The ignition control will make 3 attempts to light before lock-

ing out.

NOTICE

Burner orifices are sized to provide proper input rate using natural

gas with a heating value of 1030 BTU/Ft3(38.4 MJ/m3). If the heating

value of your gas is significantly different, it may be necessary to

replace the orifices.

NOTICE

DO NOT set manifold pressure less than 3.2 in wc or more than 3.8 in

wc for natural gas at sea level. If manifold pressure is outside this

range, change main burner orifices.

CAUTION

DO NOT bottom out gas valve regulator adjusting screw. This can

result in unregulated manifold pressure and result in excess overfire

and heat exchanger failures.

NOTICE

If orifice hole appears damaged or it is suspected to have been

redrilled, check orifice hole with a numbered drill bit of correct size.

Never redrill an orifice. A burr-free and sqaurely aligned orifice hole is

essential for proper flame characteristics.

CAUTION

Be sure to relight any gas appliances that were turned off at the start

of this input check.

5594752-UIM-C-1119

18 Johnson Controls Ducted Systems

Table 9: Gas Rate (CU FT/HR)

Seconds For

1 Revolution Size of Test Dial Seconds For

1 Revolution Size of Test Dial

1 Cu Ft 2 Cu Ft 5 Cu Ft 1 Cu Ft 2 Cu Ft 5 Cu Ft

10 360 720 1800 50 72 144 360

11 327 655 1636 51 71 141 355

12 300 600 1500 52 69 138 346

13 277 555 1385 53 68 136 340

14 257 514 1286 54 67 133 333

15 240 480 1200 55 65 131 327

16 225 450 1125 56 64 129 321

17 212 424 1059 57 63 126 316

18 200 400 1000 58 62 124 310

19 189 379 947 59 61 122 305

20 180 360 900 60 60 120 300

21 171 343 857 62 58 116 290

22 164 327 818 64 56 112 281

23 157 313 783 66 54 109 273

24 150 300 750 68 53 106 265

25 144 288 720 70 51 103 257

26 138 277 692 72 50 100 250

27 133 267 667 74 48 97 243

28 129 257 643 76 47 95 237

29 124 248 621 78 46 92 231

30 120 240 600 80 45 90 225

31 116 232 581 82 44 88 220

32 113 225 563 84 43 86 214

33 109 218 545 86 42 84 209

34 106 212 529 88 41 82 205

35 103 206 514 90 40 80 200

36 100 200 500 92 39 78 196

37 97 195 486 94 38 76 192

38 95 189 474 96 38 75 188

39 92 185 462 98 37 74 184

40 90 180 450 100 36 72 180

41 88 176 439 102 35 71 178

42 86 172 429 104 35 69 173

43 84 167 419 106 34 68 170

44 82 164 409 108 33 67 167

45 80 160 400 110 33 65 164

46 78 157 391 112 32 64 161

47 76 153 383 116 31 62 155

48 75 150 375 120 30 60 150

49 73 147 367

5594752-UIM-C-1119

Johnson Controls Ducted Systems 19

ADJUSTMENT OF MANIFOLD GAS PRESSURE &

INPUT RATE

Inlet and manifold gas pressure may be measured by connecting the

“U” tube manometer to the gas valve with a piece of tubing. Follow the

appropriate section in the instructions below. Refer to Figure 18 for a

drawing of the locations of the pressure ports on the gas valve.

Turn gas off at the ball valve or gas cock on gas supply line

before the gas valve. Find the pressure ports on the gas

valve marked Out P and In P.

1. The manifold pressure must be taken at the port marked OUT P.

2. The gas line pressure must be taken at the port marked IN P.

3. Using a 3/32” (2.4 mm) hex head wrench, loosen the set screw by

turning it 1 turn counter clockwise. DO NOT REMOVE THE SET

SCREW FROM THE PRESSURE PORT.

Read the inlet gas pressure

Connect the positive side of the manometer to the IN P Tap on the gas

valve. Do not connect any tubing to the negative side of the manometer,

as it will reference atmospheric pressure. Refer to Figure 19 for connec-

tion details.

1. Turn gas and electrical supplies on and follow the operating instruc-

tions to place the unit back in operation.

2. Once the correct gas inlet pressure has been established, see

Table 10, turn the gas valve to OFF and turn the electrical supply

switch to OFF; then remove the flexible tubing from the gas valve

pressure tap and tighten the pressure tap plug using the 3/32” (2.4

mm) hex head wrench.

3. Turn the electrical and gas supplies back on, and with the burners

in operation, check for gas leakage around the gas valve pressure

port for leakage using an approved non-corrosive gas leak detec-

tion fluid, or other non-flammable leak detection methods.

Read the manifold gas pressure

Connect the positive side of the manometer to the adapter previously

installed in the OUT P Tap on the gas valve. Do not connect any tubing

to the negative side of the manometer, as it will reference atmospheric

pressure. Refer to Figure 19 for connection details.

1. Refer to Figure 18 for location of pressure regulator adjustment cap

and adjustment screws on main gas valve.

2. Turn gas and electrical supplies on and follow the operating instruc-

tions to place the unit back in operation.

3. Adjust manifold pressure by adjusting gas valve regulator screw for

the appropriate gas per the following:

4. After the manifold pressure has been adjusted, re-calculate the fur-

nace input to make sure you have not exceeded the specified input

on the rating plate. Refer to “CALCULATING THE FURNACE

INPUT (NATURAL GAS)”.

5. Once the correct BTU (kW) input has been established, turn the

gas valve to OFF and turn the electrical supply switch to OFF; then

remove the flexible tubing from the gas valve pressure tap and

tighten the pressure tap plug using the 3/32” (2.4 mm) hex head

wrench.

6. Turn the electrical and gas supplies back on, and with the burners

in operation, check for gas leakage around the gas valve pressure

port for leakage using an approved non-corrosive gas leak detec-

tion fluid, or other non-flammable leak detection methods.

Table 10: Inlet Gas Pressure Range

INLET GAS PRESSURE RANGE

Natural Gas Propane (LP)

Minimum* 4.5” w.c. (1.12 kPa) 8.0” w.c. (1.99 kPa)

Maximum 10.5” w.c. (2.61 kPa) 13.0” w.c. (3.24 kPa)

IMPORTANT: The inlet gas pressure operating range table specifies

what the minimum and maximum gas line pressures must be for the

furnace to operate safely. The gas line pressure MUST BE a mini-

mum of:

• 7” w.c. (1.74 kPA) for Natural Gas

• 11” w.c. (2.74 kPA) for Propane (LP) Gas

in order to obtain the BTU input specified on the rating plate and/or

the nominal manifold pressure specified in these instructions and on

the rating plate.

IMPORTANT: The cap for the pressure regulator must be removed

to gain access to the adjustment screw. Loosening or tightening the

cap does not adjust the flow of gas.

Table 11: Nominal Manifold Pressure

NOMINAL MANIFOLD PRESSURE

Natural Gas 3.5" w.c. (0.87 kPa)

Propane (LP) Gas 10.0" w.c. (2.488 kPa)

FIGURE 18: Gas Valve

IMPORTANT: If gas valve regulator is turned in (clockwise), manifold

pressure is increased. If screw is turned out (counter clockwise),

manifold pressure will decrease.

MANIFOLD PRESSURE “U” TUBE CONNECTION

FIGURE 19: Reading Gas Pressure

INLET

WRENCH

BOSS

INLET

PRESSURE

PORT

OFF

ON/OFF SWITCH

(Shown in ON position)

MAIN REGULATOR

ADJUSTMENT

OUTLET

PRESSURE

PORT VENT PORT

A0226-001

878%(

0$120(7(5

,1

:$7(5

&2/801

*$6

35(6685(

6+2:1

*$6

%851(56

287/(7

35(6685(7$3

*$69$/9(

)/$0(

6(1625

´78%,1*

0$,1,)2/'

3,3(

$

5594752-UIM-C-1119

20 Johnson Controls Ducted Systems

AIRFLOW SETTINGS

Cooling Airflow Settings

This unit is equipped with a five-speed blower motor. The desired cool-

ing airflow may be selected by connecting the desired motor speed tap

wire to the HI COOL terminal on the control board. The speed should

be selected so as to deliver approximately 350-400 CFM per ton of A/C

cooling capacity. Use of airflow outside of this range may result in

diminished air conditioning performance and may result in lower overall

energy efficiency and higher electric utility bills. See Table 12 for default

cooling blower settings.

Continuous Fan Airflow Default Setting

The default blower speed for continuous fan operation is LOW speed.

The continuous fan speed is set at the factory to the default continuous

fan blower speed.

In certain circumstances, it may be necessary to move the continuous

fan speed to a different speed tap. However, doing so will result in

higher than normal electrical energy usage and higher than normal

electric utility bills.

Continuous Fan Jumpers

This furnace may be operated in continuous fan mode by setting the

wall thermostat FAN switch to ON. To select the desired continuous fan

airflow, place the FAN SPEED jumper on the control board on the pins

adjacent to the desired speed. There are four options:

1. With the FAN SPEED jumper in the “G” position, the blower will run

during continuous fan operation at the motor speed connected to

the “G” terminal on the control board.

2. With the FAN SPEED jumper in the “HI COOL” position, the blower

will run during continuous fan operation at the motor speed con-

nected to the “HI COOL” terminal on the control board.

3. With the FAN SPEED jumper in the “LO COOL” position, the blower

will run during continuous fan operation at the motor speed con-

nected to the “LO COOL” terminal on the control board.

4. With the FAN SPEED jumper in the “HEAT” position, the blower will

run during continuous fan operation at the motor speed connected

to the “HEAT” terminal on the control board.

The default position is with the jumper in the "G" position and the LOW

speed motor wire on the "G" terminal. In certain circumstances, it may

be necessary to move the continuous fan speed to a different speed

tap. However, doing so is not recommended because it will result in

higher than normal electrical energy usage and higher than normal

electric utility bills.

Gas Heating Airflow Default Setting

This unit is equipped with a five-speed blower motor. The heating

blower speed is set at the factory to the default blower speed, which is

the blower speed that will deliver the correct airflow for proper heating

operation in most applications. The default heating blower speed for

each model is shown in Table 12. Use of a heating speed other than the

default heating blower speed may result in reduced energy efficiency

and higher electric utility bills.

In certain circumstances, it may be necessary to move the heating

blower speed to a different motor speed tap. Not all five motor speeds

are appropriate for gas heating operation. The use of heating airflow on

a speed other than the default speed will result in diminished heating

performance and may cause the furnace temperature limit controls to

shut down the furnace.

Measurement of Temperature Rise

After about 5 minutes of operation, determine the furnace temperature

rise. Measure the temperature of both the return air and the heated air

in the ducts, about six feet (1.83 m) from the furnace where they will not

be affected by radiant heat. Increase the blower speed to decrease the

temperature rise. Decrease the blower speed to increase the tempera-

ture rise.

The blower speed taps are located on the furnace control board in the

blower compartment. Refer to Figure 20 and the unit-wiring label to

change the blower speed. To use the same speed tap for heating and

cooling, the heat terminal and cool terminal must be connected using a

jumper wire and connected to the desired motor lead. Place all unused

motor leads on park terminals. Two park terminals are provided.

ADJUSTMENT OF FAN CONTROL SETTINGS

This furnace is equipped with a time-on/time-off heating fan control. The

fan on delay is fixed at 30 seconds. The fan off delay has 4 settings (60,

90, 120 and 180 seconds). The fan off delay is factory set to 120 sec-

onds. The fan-off setting must be long enough to adequately cool the

furnace, but not so long that cold air is blown into the heated space.

The fan-off timing may be adjusted by positioning the jumper on two of

the four pins as shown in Figure 20.

Table 12: Default Blower Speeds

Model Number Default Blower Speeds

Heat Cool Continuous

Fan

040A12 Medium Low (4) High (1) Low (5)

060A12 Medium Low (4) High (1) Low (5)

080B12 Medium (3) High (1) Low (5)

080C16 Medium (3) High (1) Low (5)

080C20 Low (5) High (1) Low (5)

100C12 Medium High (2) High (1) Low (5)

100C16 Medium (3) High (1) Low (5)

100C20 Medium Low (4) High (1) Low (5)

120C16 Medium High (2) High (1) Low (5)

120C20 Medium Low (4) High (1) Low (5)

130D20 Medium (3) High (1) Low (5)

DANGER

The temperature rise, or temperature difference between the return

air and the supply (heated) air from the furnace, must be within the

range shown on the furnace rating plate and within the application

limitations shown in SECTION V.

The supply air temperature cannot exceed the “Maximum Supply

Air Temperature” specified in these instructions and on the furnace

rating plate. Under NO circumstances can the furnace be allowed to

operate above the Maximum Supply Air Temperature. Operating the

furnace above the Maximum Supply Air Temperature will cause pre-

mature heat exchanger failure, high levels of Carbon Monoxide, a fire

hazard, personal injury, property damage, and/or death.

Other manuals for TM8E

This manual suits for next models

Table of contents

Other Johnson Controls Furnace manuals

Johnson Controls

Johnson Controls TM9X User manual

Johnson Controls

Johnson Controls TM9T Guide

Johnson Controls

Johnson Controls TM9V*MP User manual

Johnson Controls

Johnson Controls LP9C C Guide

Johnson Controls

Johnson Controls TM9T Guide

Johnson Controls

Johnson Controls TM9X*MP User manual

Johnson Controls

Johnson Controls EBE23A User manual

Johnson Controls

Johnson Controls TM9M MP Series User manual

Johnson Controls

Johnson Controls TM9V C Series User manual

Johnson Controls

Johnson Controls TPLC060A12MP12C User manual

Johnson Controls

Johnson Controls TM9X MP Series User manual

Johnson Controls

Johnson Controls TM8X*MP Series User manual

Johnson Controls

Johnson Controls MM9E Series Guide

Johnson Controls

Johnson Controls TM9X Guide

Johnson Controls

Johnson Controls TM8X MP Series User manual

Johnson Controls

Johnson Controls TM8V MP Series User manual

Johnson Controls

Johnson Controls 33" Guide

Johnson Controls

Johnson Controls RL18 User manual

Johnson Controls

Johnson Controls TM8T*MP User manual

Johnson Controls

Johnson Controls TM9X Quick setup guide

Johnson Controls

Johnson Controls 33” Multi-position Gas Furnaces Guide

Johnson Controls

Johnson Controls GG9S*MP User manual

Johnson Controls

Johnson Controls EB Series Manual

Johnson Controls

Johnson Controls TM8M/TMLM*MP User manual

Popular Furnace manuals by other brands

United States Stove

United States Stove ASHLEY AF1600E Owner's installation and operation manual

Bryant

Bryant DELUXE 355AAV Product data

Carrier

Carrier DELUXE 58DXC Service and maintenance instruction

Bryant

Bryant B Series Service and maintenance procedures

Daikin

Daikin DM97MC Service instructions

Napoleon

Napoleon HYBRID 100 Installation and operating instructions

Carrier

Carrier 58SB0B operating instructions

Goodman

Goodman GMEC80 manual

Steffes

Steffes DLF30B Owner's and installer's manual

Carrier

Carrier 59SC2A Product data

Harman

Harman SF1500A Installation & operating manual

International comfort products

International comfort products N8MPN installation instructions

Lennox

Lennox G50UH Series installation instructions

Blue Summit

Blue Summit BG961UHE installation instructions

Lennox

Lennox G60DF(X) Series installation instructions

Carrier

Carrier 916SA Installation, start-up, operating and service and maintenance instructions

Ashley

Ashley 1440E Owner's installation and operation manual

Carrier

Carrier FED B Series installation instructions

Johnson Controls TM8E User manual

Popular Furnace manuals by other brands