Joy-it JDS6600 User manual

3
JDS6600
Dual-Channel Signal Generator

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 2
1. Introducon
2. Device Overview
3. Shortcut Overview
4. Parameter sengs in the main interface
5. Measuring and counng funcons
6. Modulaon mode
7. System sengs
8. Other Informaons
9. Support
TABLE OF CONTENTS

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 3
Dear customer,
Thank you very much for choosing our product. In the following we have listed what you have to consider
during commissioning.
1. INTRODUCTION
2. DEVICE OVERVIEW

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 4

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 5
3. SHORTCUT OVERVIEW
1CH1 Parameter
2CH2 Parameter
3waveform display
4Channel output status
5menu bar
6Phase dierence between CH1 and CH2
Conguraon of the waveform
Conguraon of the measuring mode
Acvang the modulaon mode
system sengs
Control the output of CH1 and CH2.
Used in other menus for control and conrmaon (On/O).
Moving the cursor posion
Press and hold to select channel 1 as the main display.
Press and hold to select channel 2 as the main display.

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 6
Press the buon to enable or disable simultaneous output for both channels.
Use the and keys to switch between the respecve channels. Pressing again while in the
channel acvates or deacvates the output. Press and hold the corresponding channel key to place the
channel in the main interface.
Press the buon to acvate the waveform. While the waveform is acve, the shape can be
changed quickly using the main buon. The arrow keys can be used to switch between the waveforms
and the presets.
Use the buon to highlight the frequency parameter. Then use the direcon keys to move the
cursor to the value you want to edit. Then press the Main buon to edit the respecve value. Then press
and hold the Frequency buon to change the unit (MHz, KHz, Hz, MHz).
4. PARAMETER SETTINGS IN THE MAIN INTERFACE

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 7
Press and then the buon in the measuring mode to switch between the measuring
funcon and the counng funcon.
The input signal frequency, period, posive pulse width, duty cycle and other parameters can be
measured. The measuring frequency range is between 1 Hz and 100 MHz. The measuring signal amplitude
range is between 2 MVpp and 20 Vpp. The input interface is Ext.IN.
Coupling seng: Press the buon to switch between AC and DC mode.
Gate Time Seng: Press the buon to set the gate me (0.01 - 10S). Move the cursor with the
arrow keys to select the value to be edited. Use the Skin buon to adjust the value.
Measuring mode: Press the buon to switch between the counng frequency and the counng
period.
Measurement parameters: Frequency, period, posive pulse width, negave pulse width, duty cycle.
Aer you have set all parameters, you can use the key to start the counng funcon. Use the
key to stop the funcon.
5. MEASURING AND COUNTING FUNCTIONS

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 8
Press the buon to start the modulaon mode. Press the buon to switch between the
sweep funcon (channel CH1/CH2), the pulse funcon (channel CH1) and the burst funcon (channel
CH1).
Sweep funcon: Here you can set any start and end frequency of the signal generator. The possible me
is between 0.1 and 999.9s.
In sweep mode (channel CH1), press the buons to set the start and end frequency, me,
direcon and mode. Once the seng has been selected, you can use the direcon buons and the main
knob to adjust it.
Pulse funcon: With this opon you can set the pulse wave width and the pulse me.
Within the pulse funcon (channel CH1), press the keys to select the pulse width, period,
oset and amplitude. Once a parameter is highlighted, you can adjust it with the direcon
keys. The pulse width and period can be set using the key. You can switch between ns and
us.
Burst funcon: The pulse sequence can be set to output 1-108575 periods. Burst mode is divided into
internal CH2 channel bursts, external input bursts and manual bursts. The period me of the burst is less
than the period me of the burst signal.
Within the burst funcon (channel CH1), press the buons to select the pulse number and burst mode.
Use the direcon keys to set the respecve parameters.
Aer you have made all the sengs, you can use the buon to start the corresponding funcon.
Press to exit.
6. MODULATION MODE

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 9
Press the buon to open the setup menu. Use the buons to navigate. The
following sengs can be made:
In/Out posion, sound sengs, brightness conguraon, language sengs, synchronizaon, seng the
arbitrary wave display.
Aer you have opened a corresponding seng, you can congure it with the main buon. Now press the
corresponding buon to save the sengs.
Sound sengs: The tones can be acvated or deacvated with the and buons.
Brightness conguraon: Here you can adjust the brightness in 12 dierent levels.
Language sengs: The English and Chinese languages are available here.
Synchronizaon: Channel CH1 is used as target during synchronizaon. The parameters of the CH2
channel change according to the CH1 parameters. When the synchronizaon point is highlighted, press
the keys to select the point to be synchronized.
Then use the buon to select or the buon to cancel the operaon.
Seng the arbitrary wave display: The number of waveforms in the main interface can be quickly
adjusted by turning the knob (1-60).
7. SYSTEM SETTINGS

JDS6600
Published: 06.12.2018 Copyright by Joy-IT 10
Our informaon and take-back obligaons according to the Electrical and Electronic
Equipment Act (ElektroG)
Symbol on electrical and electronic equipment:
This crossed-out dustbin means that electrical and electronic equipment does not belong in the
household waste. You must return the waste to a collecon point. Before handing over waste baeries
and accumulators that are not enclosed by waste equipment must be separated from it.
Return opons:
As an end user, you can return your old device (which essenally performs the same funcon as the new
device purchased from us) for disposal free of charge when you purchase a new device.
Small appliances with no external dimensions greater than 25 cm can be disposed of in normal household
quanes independently of the purchase of a new appliance.
Possibility of return at our company locaon during opening hours:
Simac GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn, Germany
Possibility of return in your area:
We will send you a parcel stamp with which you can return the device to us free of charge. Please contact
us by e-mail at [e-mail] or by telephone.
Informaon on packaging:
If you do not have suitable packaging material or do not wish to use your own, please contact us and we
will send you suitable packaging.
8. OTHER INFORMATION