Jung FZS 10 WW User manual
Radio plug adapter switch in SCHUKO socket housing
Radio Management
Radio plug adapter switch in SCHUKO socket housing
Art.-No.: FZS 10 WW
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Always disconnect the device from the socket outlet before
carrying out work on the device or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
Even when the device is switched off, mains voltage may be present on the load,
because only 1 pole is switched off.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1
(1) Switch adapter plug
(2) LED
(3) Programming button
(4) Fine-wire fuse
3 Function
System information
By statute, the reception characteristics and the antenna cannot be changed.
The device may be operated in all EU and EFTA countries.
The declaration of conformity can be viewed on our website.
1/5
32526813
J:0082526813 20.12.2010
The range of a radio system from the transmitter to the receiver depends on various
circumstances.
The range of the system can be optimised by selecting the optimal installation location, taking
into account the structural circumstances.
Figure 2: Reduced range due to structural obstacles
Example of penetration of various materials:
Material Penetration
Wood, plaster, plasterboard approx. 90%
brick, chipboard approx. 70%
Reinforced concrete approx. 30%
Metal, metal grid approx. 10%
Rain, snow approx. 1-40%
Intended use
- Radio-controlled switching of portable luminaires with mains plug, e.g. table or floor lamps
- Use in socket outlets
- Operation with suitable radio transmitters
i It is not possible to teach a combination of presence detector and motion detector.
Product characteristics
- Manual operation on device possible
- Light scene operation possible
- 2-point light control in combination with a radio presence detector possible
- Run-on time of approx. 1 minute in connection with radio motion detectors
- Overload protection through fine-wire fuse
4 Operation
Operation with radio transmitter
A radio transmitter has to be taught in order to be able to operate the device via radio.
i Observe the instructions for the radio transmitter.
Switching lighting on adapter plug
o Press the programming key(3) for approx. 1 second.
The light is switched on or off.
If the LED (2) lights up, the connected load is switched on.
2/5
32526813
J:0082526813 20.12.2010
Radio Management
Radio plug adapter switch in SCHUKO socket housing
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Always disconnect the device from the socket outlet before carrying out work
on the load!
Connecting the device
Maintain a distance of at least 0.5 m from metal surfaces and electrical devices, e.g. microwave
ovens, hi-fi and TV systems, electronic ballasts or transformers.
Maintain a distance of at least 1 m between transmitter and receiver in order to prevent
overmodulation of the receiver.
o Insert device into a socket outlet.
o Insert load into the device.
o Switch on load
5.2 Commissioning
i Observe the instructions for the radio transmitter.
Teaching a radio transmitter
i If all memory slots are occupied, a radio transmitter which has already been taught must
first be deleted. To do this, delete all taught channels and light scenes of the radio
transmitter individually.
The distance between the receiver and the radio transmitter is from 0.5 m to 5 m.
Load is switched off.
o Press the programming button for approx. 4 seconds.
The LED blinks. The device is in programming mode for approx. 1 minute.
o Trigger teach telegram on radio transmitter (see instructions for radio transmitter).
LED lights up. The radio transmitter has been taught.
o Press the programming button briefly.
The load switches on. The device is in operating mode.
i The programming mode is exited automatically after about 1 minute.
i Teach light scene buttons separately.
i When a radio transmitter is taught, All On and All Off buttons that are present are
automatically also taught.
Deleting radio transmitters individually
o Teach the radio transmitter to be deleted again (see Teaching a radio transmitter).
LED blinks quickly. The radio transmitter has been deleted.
i If several channels or light scenes of a radio transmitter have been taught, they all must be
deleted individually.
6 Appendix
6.1 Technical data
Rated voltage AC 230 V ~
Mains frequency 50 / 60 Hz
Ambient temperature -20 ... +55 °C
Protection rating IP 20
Fine-wire fuse D 6.3 H 250
3/5
32526813
J:0082526813 20.12.2010
Radio Management
Radio plug adapter switch in SCHUKO socket housing
Connected load
i Power specifications including transformer power dissipation.
i Operate inductive transformers with at least 85% nominal load.
Incandescent lamps 1000 W
HV halogen lamps 1000 W
Inductive transformers 750 VA
Tronic transformers 750 W
Fluorescent lamps, uncompensated 500 VA
Fluorescent lamps, parallel compensated 400 VA (47 µF)
Fluorescent lamps, duo circuit 1000 VA
Contact type µ contact
Dimensions L×W×H 136×70×72 mm
carrier frequency 433.42 MHz (ASK)
Teachable radio transmitter max. 30
6.2 Troubleshooting
Load is switched off and cannot be switched on again.
Cause: Overload protection has tripped.
Check the fine-wire fuse
Replace the fine-wire fuse Use only original fuses.
Device does not respond, or only sometimes.
Cause 1: battery in the transmitter is empty.
Change the battery.
Cause 2: Radio range exceeded. Structural obstacles reduce the range.
Check the installation situation.
Using a radio repeater.
6.3 Warranty
We reserve the right to make technical and formal changes to the product in the interest of
technical progress.
We provide a warranty as provided for by law.
Please send the unit postage-free with a description of the defect to our central customer
service office:
ALBRECHT JUNG GMBH & CO. KG
Service Center
Kupferstr. 17-19
D-44532 Lünen
Service-Line: +49 (0) 23 55 . 80 65 51
Telefax: +49 (0) 23 55 . 80 61 89
General equipment
Service-Line: +49 (0) 23 55 . 80 65 55
Telefax: +49 (0) 23 55 . 80 62 55
KNX equipment
Service-Line: +49 (0) 23 55 . 80 65 56
Telefax: +49 (0) 23 55 . 80 62 55
The Πsymbol is a free trade symbol, which is solely intended for the authorities and does not
guarantee any properties.
4/5
32526813
J:0082526813 20.12.2010
Radio Management
Radio plug adapter switch in SCHUKO socket housing
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
D-58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-1 89
E-mail: [email protected]
Internet: www.jung.de
www.jung-katalog.de
5/5
32526813
J:0082526813 20.12.2010
Radio Management
Radio plug adapter switch in SCHUKO socket housing
Table of contents
