Junlam TSB-89717-BLK User manual

PLEASE READ CAREFULLY BEFORE OPERATING THIS EQUIPMENT
MODEL:TSB-89717-BLK
INSTRUCTION MANUAL
Bluetooth Tower Speaker with LED Light Show

DANGEROUS VOLTAGE:The lighting flash with arrowhead symbol within
an equilateral triangle is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
ATTENTION:The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONG
CORD This unit has a long cord that can be easily tripped on or pulled on,
causing injury. Please make sure it is arranged so that it will not drape over a
tabletop, etc. Where it can be pulled on by children or tripped over accidentally.
FCC STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THE
COVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2
"This equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum
distance of 20 centimeters between the radiator and your body."

This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING:
To assure continued operation, follow the attached installation instructions and
use only shield cables when connecting to other devices. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Before using the unit, be sure to read all operating instruction carefully, please
note that these are general precautions and may not pertain to your unit. For
example, this unit may not have the capability to be connected to an outdoor
antenna.
1. Read these instructions
All the safety and operating instructions should be read before the appliance is
operated.
2. Keep these instructions
The safety and operating instructions should be kept for future reference.
3. Heed all warnings
All warnings on the appliance and in the operating instructions should be
adhered to.
4. Follow all instructions
All operation and use instructions should be followed.
FCC NOTICE:
5. Do not use this apparatus near water
The appliance should not be used near water; for example, near a bath tub,
3

washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool.
6. Clean only with dry cloth
The appliance should be cleaned only as recommended by the manufacturer.
7. Do not block any ventilation openings.Install in accordance with the
manufacturer’s instructions.
Slots and openings in the cabinet and in the back or bottom are provided for
ventilation, to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or similar
surface. This product should never be placed near or over a radiator or heat
source. This product should not be placed in a built-in installation, such as a
bookcase or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide or the third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments / accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
An appliance and cart combination should be moved with care. Quick stop,
excessive fore and uneven surfaces may cause the appliance and cart
combination to overturn.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
To protect your product from a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to
lightning and power-line surges.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or
4

moisture, does not operate normally, or has been dropped.
15. Power source
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company. For products
intended to operate from battery power, or other source, refer to the operation
instructions.
16. Power lines
An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of
fire or electric shock.
18. Object and liquid entry
Never push objects of any kind into the product through openings as they may
touch dangerous voltage points or short out parts that could result in fire or
electric shock. Never spill or spray any type of liquid on the product.
19. Outdoor antenna grounding
If an outside antenna is connected to the product, be sure the antenna system
is grounded so as to provide some protection against voltage surges and built
up static charges. Section 810 of the National Electric Code ANSI/ NFPA 70
provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead- in wire to an antenna discharge
product, size of grounding conductors, location of antenna- discharge product,
connection to grounding electrodes and requirements for the grounding
electrodes.
5

20. Service
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
b)If liquid has been spilled or objects have fallen into the product.
c)If the product has been exposed to rain or water.
d)If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as an adjustment of other controls may result in damage and will
require extensive work by a qualified technician to restore the product to its
normal operation.
e)If the product has been dropped or the cabinet has been damaged.
f)When the product exhibits a distinct change in performance- this indicates a
need for service.
25. Note to CATV system installer
This reminder is provided to call the CATV system installer' s attention to
Article 820- 40 of the NEC that provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as
practical.
NOTE: Refer all servicing to qualified service personnel. Servicing is
required when the unit has been damaged in any way such as the
following: the power-supply cord or plug has been damaged, liquid has
been spilled into unit, the unit has been exposed to rain or moisture, the
unit has been dropped or the unit does not operate normally.
21. Replacement parts
When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or those that have the same
characteristics as the original parts. Unauthorized substitutions may result in
fire or electric shock or other hazards.
22. Safety check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
23. Wall or ceiling mounting
The product should be mounted to a wall or ceiling only as recommended by
the manufacturer.
24. Damage requiring service
Unplug this product from the wall outlet and refer service to qualified service
personnel under the following conditions.
a)When the power- supply cord or plug is damaged.
6

INSTALLATION
Washers
Baseplate
Screws
Installing the baseplate
CAUTION: The unit must never be used without the baseplate attached.
Lay a soft protective cloth on a large table or work-surface.
Fit a washer to each of the special screws.
Lining up the holes in the baseplate with the holes in the base.
Lay the unit on the cloth, with the base accessible.
Screw in the two special screws to secure the base.
Fold down the finger grips on the screw heads.
Tighten the screws with screwdriver.
The baseplate is now assembled to the unit.
Carefully lift the unit off the table and stand it on its base.
7

MAIN UNIT
LOCATION OF CONTROLS
ANT
ANT
35
910
11
12
13
14
15
4. AUX IN Jack
3. Indicator
6. SOURCE Button
7. MODE, LED ON/OFF Button
8. POWER Button
9. Play/Pause Button
10. TUNE- (Previous) Button
11. TUNE+ (Next) Button
12. VOL+(Volume Up)
13. VOL-(Volume Down)
14. FM Antenna
15. DC IN Jack
USB CHARGE
4
5. USB CHARGE Port
1
1. Remote Sensor
DC IN
D V A
C
9 /2
6
7
8
2
2. LED Display
MODE
LED ON/OFF
8
DC IN
DC 9V/2.5A

1
2
3
5
6
7
5.SOURCE Button
8.ST/MO(stereo/mono) Button
1.POWER Button
7. (play/pause) Button
2.TUNE- (previous) Button
TUNE+ (next) Button
VOL+(volume up)
3.VOL- (volume down)
6. (mute) Button
POWER
SOURCE
TUNE- TUNE+
VOL
ST/MO
LED
ON/OFF LED
MODE 9
4
8
4.LED ON/OFF Button 9.LED Mode Button
9

REMOTECONTROLOPERATIONRANGE
Fig.1 Fig.2 Fig.3
-First Time Use
Remove and discard the insulation tab as figure on the right.
-Replacing Batteries For Remote Control
1. Push and slide out the battery holder as figure 1 below.
3. Close the battery holder.
2. Replace the battery with a new CR2025 button cell as the polarity
markings on the rear of the Remote Control.
CAUTION
Danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type.
BATTERY PRECAUTIONS
Follow these precautions when using a battery in this device:
1. Use only the size and type of battery specified.
2. Be sure to follow the correct polarity when installing the battery as indicated in the
battery compartment, a reserved battery may cause damage to the device.
3. Do not mix different types of batteries together ( e.g: Alkaline and Carbon-zinc ) or old
batteries with fresh ones.
4. If the batteries in the device are consumed or the device is not to be used for a long
period of time, remove the batteries to prevent damage or injury from possible leakage.
rupture. ( Follow battery manufacturer’s instructions.)
6. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
7. Clean the battery contacts and also those of the device prior to battery installation.
5. Do not try to recharge the battery not intended to be recharged; it can overheat and
- When there is an obstacle between the remote and the transmitter, the unit may not operate.
- When direct sunlight, an incandescent lamp, flurescent lamp or any other strong light shines
on the REMOTE SENSOR of the unit, the operation of the remote may be unstable.
8. The remote control supplied with a coin/button cell
battery. If the coin button cell battery is swallowed,
it can cause severe internal burns in just 2 hours
and can lead to death.
Keep new and used battery away from children.
If the battery compartment does not close securely,
stop using the product and keep it away from children.
If you think batteries might have been swallowed or
placed any part of the body, seek immediate medical
attention.
CR2025
10

~ Green: Radio
~ Blue: Bluetooth
4. During Playback:
~ Press the VOL- or VOL+ (Volume) buttons to adjust volume level as desired.
~ Press the button on remote control to turn off the sound, press again to resume.
to shut off the unit if no using for long period of time.
NOTE:
Pull out the AC/DC Adapter plug
GENERAL OPERATIONS
1. Insert the AC/DC Adapter plug into a conveniently located AC outlet having 100-240V~50/60Hz.
The Indicator will light up Red.
2. Press the Power button on the unit to power on the unit.
corresponding color as below:
3. Press the SOURCE button repeatedly to switch to desired mode.The color of Indicator turns
to
5. When finished listening, press the Power button to power off the unit.The indicator will
turn Red.
~ Press the or button to skip track.
~ Press the (Play/Pause) button to pause. Press again to resume normal playback.
~ Violet: AUX IN
~ Press the LED ON/OFF button on remote control to turn on the led light, press the LED
MODE button on remote control to change the LED light mode(total 5 modes).
~ Press and hold the MODE/ LED ON/OFF button on the unit to turn on the led light, press
the MODE /LED ON/OFF button on the unit to change the LED light mode(total 5 modes).
Press the LED ON/OFF button on remote control again to turn off the LED light.
Press and hold the MODE/ LED ON/OFF button on the unit again to turn off the LED light.
11

NOTE: When power is off, or unplugging the adapter, station need to be re-searched.
FM RADIO
NOTE: If the reception is not good, please unwind and extend the antenna to get better reception.
Power on the unit and press the SOURCE button repeatedly until the indicator turns GREEN.
1. Press TUNE- or TUNE+ button to search manually to play the available station.
2. Press and hold TUNE- or TUNE+ to search station automatically until a station is found, and it will
play automatically.
During palyback:
Press the VOL (Volume) +/- buttons to adjust volume level.
4. Press the SOURCE button repeatedly until the color of Indicator turns to VIOLET.
3. Power ON the unit.
1. Connect one end of supplied audio connection cable to the AUX IN jack on the top of the unit.
2. Connect the other end to the Audio out/Line out/Phone jack on the external player (such like
iPhone, iPad, MP3 player, Discman... etc.).
5. Play the music in the external player as usual.
LISTEN TO EXTERNAL AUDIO DEVICES
3. If the available FM station is stereo, the unit will play it in stereo mode automatically.
If the reception is no good, press the MO/ST button on remote control to switch to Mono
mode. Press again to turn back to Stereo mode.
12

1. Power ON the unit.
4. During palyback:
Press the VOL (Volume) +/- buttons to adjust volume level.
Press the or button to skip track.
Press the (Play/Pause) button to pause. Press again to resume normal playback.
NOTES:
BLUETOOTH PAIRING AND PLAYBACK
Pairing the external Bluetooth compatible device for the first time as below:
A. Power ON the unit, press the SOURCE button repeatedly until the
B. Power ON the external device and enter searching mode. Start pairing as the on screen
instructions on the external device (For details pairing procedures, please refer to the user’s
manual of your Bluetooth compatible device.).
C. When the external device searched the unit, the pairing name “TSB-89717-BLK” will appear on
2. Press the SOURCE button repeatedly until the color of Indicator turns BLUE.
Indicator turns to
Blue and blinking.
the display of external device. Select it and make pairing.
D. Pairing code “0000” may be needed to enter.
E. After successful connection, the Blue indicator will stay lit, then play music as usual.
3. Turn on the Bluetooth function on the external device, it will connect with the unit automatically,
then play the music as usual.
USB CHARGE
2.Insert one end of the USB charging cable to the USB CHARGE port, insert the other end to
the external device to charge.
NOTE:
The output power is DC5V, 2.1A.
1. Power on the unit.
13

Check the followings before requesting service
SYMPTOM POSSIBLE CAUSE POSSIBLE SOULTION
desired mode.
Press the SOURCE button repeatedly to
set the input source to the desired mode
TROUBLESHOOTING GUIDE
No power
No sound
Sound distortion
Volume level too high
Bass level of the connected
device too high
Input source incorrect
The connected device is not
in payback mode
Volume in minimum position
wall outlet Plug to the wall outlet.
Raise volume level by pressing the VOL
(Volume) + button
Play the music/movie in the connected
device as usual and make sure the
volume level of it is in high level
Reduce the bass level of the connected
device
VOL (Volume ) - button
Reduce the volume level by pressing
the
AC/DC adapter plug not
connected to the
Bluetooth
reception failure
Have not paired
The external device is far from
the unit Put the external BT device close to the
unit
Pair both units as BT pairing page
14

Accessories
TECHNICAL SPECIFICATIONS
Speakers ............................................................................................................................... 5W x 2
Bluetooth Working Distance...........................................................................................Up to 30 feet
(Measured in open area. Wall
and structures may affect the effective range.)
1 x AUX IN Cable
1 x User Manual
1 x AC/DC Adapter
AC/DC Adapter
Input........................................................................................................AC 100-240V~50/60Hz
Output..............................................................................................DC 9V 2.5 A
FM 87.5 -108.0 MHz
Radio Coverage.................................................................................................
is a trademark on a registered trademark of Bluetooth
SIG Inc. All other trademarks and trade names are
those of their respective owners.
2 x Assembling Screws with Washers
1 x Base Plate
1 x Remote Control
15