JVC KW-V255DBT User manual

KW-V255DBT (Region 2 – DVD Region Code 2 Area)
KW-V250BT (Region 2 – DVD Region Code 2 Area)
KW-V250BT (Region 5 – DVD Region Code 5 Area)
MONITOR WITH DVD RECEIVER
INSTRUCTION MANUAL
This instruction manual is used to describe models listed above. Model availability and features (functions)
may differ depending on the country and sales area. B5A-2614-00 (E/Q)
ENGLISH
00_KWV_2019ST_EQ_EN.indb 100_KWV_2019ST_EQ_EN.indb 1 29/6/2018 11:56:56 AM29/6/2018 11:56:56 AM

ENGLISHi
Important NoticeImportant Notice
To ensure proper use, please read through this
manual before using this product. It is especially
important that you read and observe WARNINGS
and CAUTIONS in this manual.
Please keep the manual in a safe and accessible
place for future reference.
WARNINGS
To prevent accidents and damages
• DO NOT install any unit or wire any cable in a
location where;
–it may obstruct the steering wheel and gearshift
lever operations.
–it may obstruct the operation of safety devices such
as air bags.
–it may obstruct visibility.
• DO NOT raise the volume level too much, as this will
make driving dangerous by blocking outside sounds,
and may cause hearing loss.
• DO NOT operate the unit while driving. If you need
to operate the unit while driving, be sure to look
around carefully.
• Stop the car before performing any complicated
operations.
• The driver must not watch the monitor while driving.
CAUTIONS
To care for the unit
• If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
To care for the monitor
• The monitor built into this unit has been produced
with high precision, but it may have some ineffective
dots. This is inevitable and is not considered
defective.
• Do not expose the monitor to direct sunlight.
• Do not operate the touch panel using a ball-point
pen or similar tool with a sharp tip.
Touch the keys on the touch panel with your finger
directly (if you are wearing a glove, take it off).
• When the temperature is very cold or very hot...
–Chemical changes occur inside, causing
malfunction.
–Pictures may not appear clearly or may move
slowly. Pictures may not be synchronized with
the sound or picture quality may decline in such
environments.
On the volume setting
• Digital devices produce very little noise compared
with other sources. Lower the volume before playing
these digital sources to avoid damaging the speakers
by sudden increase of the output level.
The marking of products using lasers
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
For Israel
00_KWV_2019ST_EQ_EN.indb i00_KWV_2019ST_EQ_EN.indb i 29/6/2018 11:56:57 AM29/6/2018 11:56:57 AM

ENGLISH ii
Important NoticeImportant Notice
Information on Disposal of Old Electrical and
Electronic Equipment and Batteries (applicable
for countries that have adopted separate waste
collection systems)
Products and batteries with the symbol (crossedout
wheeled bin) cannot be disposed as household waste.
Old electrical and electronic equipment and batteries
should be recycled at a facility capable of handling
these items and their waste byproducts.
Contact your local authority for details in locating a
recycle facility nearest to you.
Proper recycling and waste disposal will help conserve
resources whilst preventing detrimental effects on our
health and the environment.
Notice: The sign “Pb” below the symbol for batteries
indicates that this battery contains lead.
Declaration of Conformity with regard to the RE
Directive 2014/53/EU
Declaration of Conformity with regard to the RoHS
Directive 2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,
Kanagawa, 221-0022, Japan
EU Representative:
JVCKENWOOD Europe B.V.
Amsterdamseweg 37, 1422 AC UITHOORN,
THE NETHERLANDS
English
Hereby, JVCKENWOOD declares that the radio
equipment “KW-V255DBT/KW-V250BT” is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
http://www.jvc.net/cs/car/eudoc/
Français
Par la présente, JVCKENWOOD déclare que
l’équipement radio « KW-V255DBT/KW-V250BT » est
conforme à la directive 2014/53/UE.
L’intégralité de la déclaration de conformité UE est
disponible à l’adresse Internet suivante :
http://www.jvc.net/cs/car/eudoc/
Deutsch
Hiermit erklärt JVCKENWOOD, dass das Funkgerät
“KW-V255DBT/KW-V250BT” der Richtlinie 2014/53/EU
entspricht.
Der volle Text der EU-Konformitätserklärung steht
unter der folgenden Internetadresse zur Verfügung:
http://www.jvc.net/cs/car/eudoc/
Nederlands
Hierbij verklaart JVCKENWOOD dat de radioapparatuur
“KW-V255DBT/KW-V250BT” in overeenstemming is met
Richtlijn 2014/53/EU.
De volledige tekst van de EU-verklaring van
overeenstemming is te vinden op het volgende
internetadres:
http://www.jvc.net/cs/car/eudoc/
00_KWV_2019ST_EQ_EN.indb ii00_KWV_2019ST_EQ_EN.indb ii 29/6/2018 11:56:57 AM29/6/2018 11:56:57 AM

ENGLISHiii
Important NoticeImportant Notice
Italiano
Con la presente, JVCKENWOOD dichiara che
l΄apparecchio radio “KW-V255DBT/KW-V250BT” è
conforme alla Direttiva 2014/53/UE.
Il testo integrale della dichiarazione di conformità UE è
disponibile al seguente indirizzo internet:
http://www.jvc.net/cs/car/eudoc/
Español
Por la presente, JVCKENWOOD declara que el equipo
de radio “KW-V255DBT/KW-V250BT” cumple la
Directiva 2014/53/EU.
El texto completo de la declaración de conformidad
con la UE está disponible en la siguiente dirección de
internet:
http://www.jvc.net/cs/car/eudoc/
Português
Deste modo, a JVCKENWOOD declara que o
equipamento de rádio “KW-V255DBT/KW-V250BT” está
em conformidade com a Diretiva 2014/53/UE.
O texto integral da declaração de conformidade da UE
está disponível no seguinte endereço de internet:
http://www.jvc.net/cs/car/eudoc/
Polska
Niniejszym, JVCKENWOOD deklaruje, że sprzęt radiowy
“KW-V255DBT/KW-V250BT” jest zgodny z dyrektywą
2014/53/UE.
Pełny tekst deklaracji zgodności EU jest dostępny pod
adresem:
http://www.jvc.net/cs/car/eudoc/
Český
Společnost JVCKENWOOD tímto prohlašuje, že rádiové
zařízení “KW-V255DBT/KW-V250BT” splňuje podmínky
směrnice 2014/53/EU.
Plný text EU prohlášení o shodě je dostupný na
následující internetové adrese:
http://www.jvc.net/cs/car/eudoc/
Magyar
JVCKENWOOD ezennel kijelenti, hogy a „KW-V255DBT/
KW-V250BT“ rádióberendezés megfelel a 2014/53/EU
irányelvnek.
Az EU konformitási nyilatkozat teljes szövege az alábbi
weboldalon érhető el:
http://www.jvc.net/cs/car/eudoc/
Svenska
Härmed försäkrar JVCKENWOOD att radioutrustningen
“KW-V255DBT/KW-V250BT” är i enlighet med direktiv
2014/53/EU.
Den fullständiga texten av EU-försäkran om
överensstämmelse finns på följande Internetadress:
http://www.jvc.net/cs/car/eudoc/
Suomi
JVCKENWOOD julistaa täten, että radiolaite
“KW-V255DBT/KW-V250BT” on direktiivin 2014/53/EU
mukainen.
EU-vaatimustenmukaisuusvakuutusvaatim us löytyy
kokonaisuudessaan seuraavasta internet-osoitteesta:
http://www.jvc.net/cs/car/eudoc/
Slovensko
S tem JVCKENWOOD izjavlja, da je radijska oprema
»KW-V255DBT/KW-V250BT« v skladu z Direktivo
2014/53/EU.
Celotno besedilo direktive EU o skladnosti je dostopno
na tem spletnem naslovu:
http://www.jvc.net/cs/car/eudoc/
Slovensky
Spoločnosť JVCKENWOOD týmto vyhlasuje, že rádiové
zariadenie „KW-V255DBT/KW-V250BT“ vyhovuje
smernici 2014/53/EÚ.
Celý text EÚ vyhlásenia o zhode nájdete na
nasledovnej internetovej adrese:
http://www.jvc.net/cs/car/eudoc/
Dansk
Herved erklærer JVCKENWOOD, at radioudstyret
“KW-V255DBT/KW-V250BT” er i overensstemmelse med
Direktiv 2014/53/EU.
EU-overensstemmelseserklæringens fulde ordlyd er
tilgængelig på følgende internetadresse:
http://www.jvc.net/cs/car/eudoc/
Ελληνικά
Με το παρόν, η JVCKENWOOD δηλώνει ότι ο
ραδιοεξοπλισμός «KW-V255DBT/KW-V250BT»
συμμορφώνεται με την Οδηγία 2014/53/ΕΕ.
Το πλήρες κείμενο της δήλωσης συμμόρφωσης της
ΕΕ είναι διαθέσιμο στην ακόλουθη διεύθυνση στο
διαδίκτυο:
http://www.jvc.net/cs/car/eudoc/
00_KWV_2019ST_EQ_EN.indb iii00_KWV_2019ST_EQ_EN.indb iii 29/6/2018 11:56:57 AM29/6/2018 11:56:57 AM

ENGLISH iv
Important NoticeImportant Notice
Eesti
Käesolevaga JVCKENWOOD kinnitab, et „KW-V255DBT/
KW-V250BT“ raadiovarustus on vastavuses direktiiviga
2014/53/EL.
ELi vastavusdeklaratsiooni terviktekst on kättesaadav
järgmisel internetiaadressil:
http://www.jvc.net/cs/car/eudoc/
Latviešu
JVCKENWOOD ar šo deklarē, ka radio aparatūra
„KW-V255DBT/KW-V250BT” atbilst direktīvas
2014/53/ES prasībām.
Pilns ES atbilstības deklarācijas teksts ir pieejams šādā
tīmekļa adresē:
http://www.jvc.net/cs/car/eudoc/
Lietuviškai
Šiuo JVCKENWOOD pažymi, kad radijo įranga
„KW-V255DBT/KW-V250BT“ atitinka 2014/53/EB
direktyvos reikalavimus.
Visą EB direktyvos atitikties deklaracijos tekstą galite
rasti šiuo internetiniu adresu:
http://www.jvc.net/cs/car/eudoc/
Malti
B’dan, JVCKENWOOD jiddikjara li t-tagħmir tar-radju
“KW-V255DBT/KW-V250BT” huwa konformi mad-
Direttiva 2014/53/UE.
It-test kollu tad-dikjarazzjoni ta’ konformità huwa
disponibbli fl-indirizz intranet li ġej:
http://www.jvc.net/cs/car/eudoc/
HRVATSKI / SRPSKI JEZIK
JVCKENWOOD ovim izjavljuje da je radio oprema
“KW-V255DBT/KW-V250BT” u skladu s Direktivom
2014/53/EU.
Cjeloviti tekst deklaracije Europske unije o usklađenosti
dostupan je na sljedećoj internet adresi:
http://www.jvc.net/cs/car/eudoc/
ROMÂNĂ
Prin prezenta, JVCKENWOOD declară că echipamentul
radio “KW-V255DBT/KW-V250BT” este în conformitate
cu Directiva 2014/53/UE.
Textul integral al declarației de conformitate UE este
disponibil la urmatoarea adresă de internet:
http://www.jvc.net/cs/car/eudoc/
БЪЛГАРСКИ
С настоящото JVCKENWOOD декларира, че
радиооборудването на “KW-V255DBT/KW-V250BT” е в
съответствие с Директива 2014/53/ЕС.
Пълният текст на ЕС декларацията за съответствие е
достъпен на следния интернет адрес:
http://www.jvc.net/cs/car/eudoc/
Turkish
Burada, JVCKENWOOD “KW-V255DBT/KW-V250BT”
radyo ekipmanının 2014/53/AB Direktifine uygun
olduğunu bildirir.
AB uyumluluk deklarasyonunun tam metni aşağıdaki
internet adresinde mevcuttur.
http://www.jvc.net/cs/car/eudoc/
Русский
JVCKENWOOD настоящим заявляет, что
радиооборудование «KW-V255DBT/KW-V250BT»
соответствует Директиве 2014/53/EU.
Полный текст декларации соответствия ЕС доступен
по следующему адресу в сети Интернет:
http://www.jvc.net/cs/car/eudoc/
Українська
Таким чином, компанія JVCKENWOOD заявляє,
що радіообладнання «KW-V255DBT/KW-V250BT»
відповідає Директиві 2014/53/EU.
Повний текст декларації про відповідність ЄС можна
знайти в Інтернеті за такою адресою:
http://www.jvc.net/cs/car/eudoc/
00_KWV_2019ST_EQ_EN.indb iv00_KWV_2019ST_EQ_EN.indb iv 29/6/2018 11:56:57 AM29/6/2018 11:56:57 AM

About this manual
The displays and panels shown in this manual are
examples used to provide clear explanations of the
operations. For this reason, they may be different
from the actual displays or panels.
Illustrations of KW-V250BT are mainly used for
explanation.
The region code of a particular model will only
be stated if only one of the regions supports the
particular feature with the same model name.
This manual mainly explains operations using the
buttons on the monitor panel and keys on the
touch panel. For operations using the remote
controller, see page 39.
< > indicates the various screens/menus/
operations/settings that appear on the touch
panel.
[ ] indicates the keys on the touch panel.
Indication language: English indications are used
for the purpose of explanation. You can select the
indication language from the <Settings> menu.
(Page 30)
ContentsContents
Component Names and Operations...............3
Basic Operations.................................................3
How to reset your unit ..........................................................3
Turning on the power ...........................................................3
Turning off the power............................................................3
Turning off the AV source....................................................4
Turning off the screen and button
illumination ..................................................................................4
Adjusting the volume............................................................4
Getting Started ...................................................4
Initial settings..............................................................................4
Clock settings..............................................................................5
Various Screens and Operations .....................6
Home screen ...............................................................................6
Source control screen............................................................6
List/setting screen....................................................................8
Disc........................................................................9
Video...................................................................10
USB......................................................................12
Android...............................................................14
iPod/iPhone.......................................................14
Tuner...................................................................15
Digital Radio (DAB) ..........................................18
Spotify ................................................................21
Other External Components ..........................23
AV-IN..............................................................................................23
Rear view camera...................................................................23
Bluetooth® .........................................................24
Information................................................................................24
Preparation................................................................................24
Connection................................................................................24
Bluetooth mobile phone..................................................26
Bluetooth audio player.......................................................28
JVC Streaming DJ ........................................................28
Bluetooth settings.................................................................29
Settings ..............................................................30
Audio settings..........................................................................30
Display settings.......................................................................33
Input settings...........................................................................35
System settings.......................................................................36
Key settings ...............................................................................38
Remote Controller............................................39
Preparation................................................................................39
Basic operations......................................................................40
Searching for an item directly........................................40
JVC Remote APP...........................................................40
Installation and Connection...........................41
Before installation..................................................................41
Installing the unit...................................................................42
Installing the trim plate......................................................42
Removing the unit................................................................42
Wiring connection................................................................43
Connecting external components .............................44
References .........................................................44
Maintenance.............................................................................44
More information...................................................................44
Troubleshooting...............................................47
Specifications....................................................50
Trademarks and licenses...................................................53
2ENGLISH
00_KWV_2019ST_EQ_EN.indb 200_KWV_2019ST_EQ_EN.indb 2 29/6/2018 11:56:57 AM29/6/2018 11:56:57 AM

Component Names and OperationsComponent Names and Operations
1Reset button
2Loading slot
3Screen (touch panel)
4Monitor panel
5Illumination bar
The brightness of the illumination changes
according to the music level. (Page 34)
6Volume +/–buttons
7FNC-button
• FNC (Press, blink once): Pops up the short-cut
menu. (Page 8)
• (Hold, blink twice): Enters favorite setting.
Default: Displays <Sound Effect> screen.
(Page30)
Basic OperationsBasic Operations
How to reset your unit
If the unit fails to operate properly, press the reset
button.
Turning on the power
Turning off the power
8-button
• (Press): Turns on the power.
• (Press): Displays the Home screen while the
power is on.
• (Hold): Activates the voice dialing.
9USB input terminal
3
ENGLISH
00_KWV_2019ST_EQ_EN.indb 300_KWV_2019ST_EQ_EN.indb 3 29/6/2018 11:56:57 AM29/6/2018 11:56:57 AM

Initial settings
When you power on the unit for the first time or reset
the unit, the <Initial Settings> screen appears.
Perform the initial settings.
Once completed, the Home screen appears.
<Demonstration>
• ON (Initial): Activates the display demonstration.
• OFF: Deactivates the display demonstration.
Getting StartedGetting Started
Turning off the AV source
1 Display the source/option selection
screen.
On the Home screen, touch as follows:
2 Turn off the AV source.
On the source/option selection screen, touch as
follows:
Turning off the screen and button
illumination
1 Display the pop-up short-cut menu.
2 On the pop-up short-cut menu, touch as
follows:
(Hold)
To turn on the screen and button illumination:
Press FNC on the monitor panel or touch the screen.
Basic OperationsBasic Operations
Adjusting the volume
You can adjust the volume (00 to 35) by pressing +to
increase and pressing –to decrease.
• Holding +increases the volume continuously to
level 15.
4ENGLISH
00_KWV_2019ST_EQ_EN.indb 400_KWV_2019ST_EQ_EN.indb 4 29/6/2018 11:56:57 AM29/6/2018 11:56:57 AM

Getting StartedGetting Started
Clock settings
1 Display the Home screen.
2 Display the <Clock> screen.
On the Home screen, touch as follows:
Then, on the <Settings> screen, touch as follows:
[System] <Clock> : [Enter]
• You can also display the <Clock> screen by
touching the clock area on the Home screen.
<Language>
Select the text language used for on-screen
information.
• English/Español/Français/Deutsch/Italiano/
Nederlands/Ελληνικά/Português/Türkçe/Čeština/
Polski/Magyar/Руccĸий/ / /
/ / / /Bahasa
Malaysia/Bahasa Indonesia/
–For external monitors, only English/Spanish/
French/German/Italian/Dutch/Russian/Portuguese
are available. If another language has been
selected, the text language for external monitors
will be set to English.
Initial:
KW-V255DBT/KW-V250BT Region 2: English
KW-V250BT Region 5: Руccĸий
• GUI Language (Local (the language selected above)
(Initial)/English): Selects the language used for
displaying operation keys and menu items.
<Rear Camera> (Page 35)
Make the settings to display the picture from the
connected rear view camera.
<User Customize> (Page 33)
Change the display design.
<Viewing Angle> (Page 35)
Select the viewing angle in relation to the monitor to
make the image on the screen easier to see.
• Under 0° (Initial)/5°/10°/15°/20°
3 Set the clock time.
<Synchronize>
• Radio Data System*1: Synchronizes the clock
time with FM Radio Data System.
• DAB*2: Synchronizes the clock time with the
Digital Radio (DAB).
• Off: Sets the clock manually. Touch [J]/[K]to
adjust the hour, then minute.
–Touching [Reset] will set the minute to “00”.
Initial:
KW-V250BT: Radio Data System
KW-V255DBT: DAB
*1 Only for KW-V250BT.
*2 Only for KW-V255DBT.
5ENGLISH
00_KWV_2019ST_EQ_EN.indb 500_KWV_2019ST_EQ_EN.indb 5 29/6/2018 11:56:58 AM29/6/2018 11:56:58 AM

Various Screens and OperationsVarious Screens and Operations
Available playback sources and options
Touch 2to display the source/option selection screen.
E.g. Source/option selection screen for KW-V250BT
Region 2
Touching the operation keys performs the following
actions:
[Tuner] Switches to the radio broadcast.
[Disc] Plays a disc.
[USB] Plays files on a USB device.
[iPod] Plays an iPod/iPhone.
[Android™] Plays an Android device.
[AV-IN] Switches to an external component
connected to the AV-IN input
terminal.
[BT Audio] Plays a Bluetooth audio player.
[Spotify]*1 Switches to the Spotify application.
[AV Off] Turns off the AV source.
[DAB]*2 Switches to the Digital Radio (DAB).
[Home] Displays the Home screen.
[Setup] Displays the <Settings> screen.
[ Power Off] Turns off the power.
[Camera] Switches to the camera connected
to the rear view camera input.
[Now Playing] Displays the source currently
played back.
*1 Only for KW-V255DBT/KW-V250BT Region 2.
*2 Only for KW-V255DBT.
To return to the Home screen
Touch [HOME] on the source/option selection screen.
Source control screen
You can perform the playback operation from the
source control screen during playback.
• The operation keys and information displayed vary
depending on the selected source/disc type/file type
being played.
• If the operation keys are not displayed on the screen,
touch the screen to show them.
You can display or change to other screens at any time
to show information, change the AV source, change
the settings, etc.
Home screen
• You can customize the Home screen. (Page 35)
• To display the Home screen from other screens, press
-.
Touching the operation keys performs the following
actions:
1Selects or changes the playback source.
2Displays all playback sources and options.
3Displays the <Settings> screen.
4Displays the <Clock> screen.
5Displays the current playing source control screen.
6Displays the phone control screen.
6ENGLISH
00_KWV_2019ST_EQ_EN.indb 600_KWV_2019ST_EQ_EN.indb 6 29/6/2018 11:56:58 AM29/6/2018 11:56:58 AM

Various Screens and OperationsVarious Screens and Operations
E.g. Common audio playback source screen:
1Playback source or media type
2Picture/artwork (shown if the file contains the
information)
3Track/file/song/video information
• Touching [H]scrolls the text if not all of the text
is shown.
4Clock display
5Current playback item information
(folder no./file no./track no./total track no./playback
file type)
6Displays/hides other available operation keys*
7Operation keys*
8IN indicator (lights up while a disc is inserted)
9Playing time/playback status
pPlayback mode indicator (Repeat/Random)
qFile type indicator
* See the following “Common operation keys on source control
screen”.
* About playback mode:
–Available playback modes differ depending on the source, disc
type, connected device, etc.
–You cannot activate repeat playback mode and random
playback mode at the same time.
–To cancel the playback mode, touch repeatedly until the
indicator disappears.
Using gesture control
You can also control playback by moving your finger
on the touch panel as follows (for some sources, the
gesture control is not available).
• Sliding the finger up/down:
Selects a folder.
• Sliding the finger left/right:
Selects an item (chapter/track/audio file/video file).
• Moving your finger clockwise/counterclockwise:
Increases/decreases the volume.
Common operation keys on source control screen
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• Available operation keys differ depending on the
selected source or connected device.
Touching the operation keys performs the following
actions:
6
[I] Displays other available operation keys
besides those shown on 7.
• To hide the window, touch [H].
[ ][ ] Selects a folder.
[ ] Selects repeat playback mode.*
[o]Stops playback.
[MODE] Displays the setting screen of the current
playback source.
7
[ ] Displays the <Equalizer> screen.
(Page30)
[ ] Displays the folder list/track list/audio
menu/video menu.
[S]/[T]• (Touch) Selects an item (chapter/
folder/track/audio file/video file).
• (Hold) Reverses/forwards search.
• (Hold) Plays in slow-motion while
paused for video playback.
[IW]Starts/pauses playback.
[ ] Selects random playback mode.*
7
ENGLISH
00_KWV_2019ST_EQ_EN.indb 700_KWV_2019ST_EQ_EN.indb 7 29/6/2018 11:56:58 AM29/6/2018 11:56:58 AM

Using the pop-up short-cut menu
While displaying the source control screen, you can
jump to another screen by touching the operation
keys on the pop-up short-cut menu.
1 Display the pop-up short-cut menu.
2 Select an item to jump to by touching as
follows.
[M] Ejects the disc from loading slot.
[ - ] • (Touch) Switches the screen.
• (Hold) Turns off the screen.
[ ]* Displays the <Settings> screen.
(Page 30)
[ ]* Displays the <User Customize>
screen and you can change the
background design. (Page 33)
[ ]* Displays the <Screen
Adjustment> screen. (Page 35)
[ ]* Displays the picture from the
connected rear view camera.
* You can customize these pop-up short-cut menu. For details, see
<Key Customize> on page 38.
To close the pop-up menu
Press FNC on the monitor panel.
Various Screens and OperationsVarious Screens and Operations
Using touch screen operation during
playback
Touching the areas performs the following actions:
1Displays the video control menu while playing a
video.
2While playing a video: Displays the source control
screen.
While playing an audio file: Displays the playback
operation keys.
3Goes to the previous chapter/track.*
4Goes to the next chapter/track.*
* Not available for video from an external component (AV-IN).
List/setting screen
Below are the common operation keys which appear
on the list/setting screen.
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• Available operation keys differ depending on the
setting screens. Not all these operation keys are
shown on every screen.
Touching the operation keys performs the following
actions:
1Enters alphabet search* to list the items in
alphabetical order. When a keypad appears, touch
the first letter you want to search for.
• For “USB” source, you can switch between the
folder list and file list by touching [ ] or [ ].
Then, touch [OK] to start searching.
2Returns to the root folder.
3Returns to the upper layer.
4Closes the current screen.
5Exits from the current screen or returns to the
previous screen.
6Changes the page to display more items.
* Alphabet search is not available:
–For Android source
–When the playlist is selected
8ENGLISH
00_KWV_2019ST_EQ_EN.indb 800_KWV_2019ST_EQ_EN.indb 8 29/6/2018 11:56:58 AM29/6/2018 11:56:58 AM

DiscDisc
Selecting a folder/track on the list
1 Display the folder/track list.
On the source control screen, touch as follows:
2 Select the folder (1), then the item (2) in
the selected folder.
Select an item in each layer until you reach and
select the desired file.
Settings for disc playback
• Available items shown on the <DISC Mode> screen
differ depending on the type of disc/file being
played back.
1 Display the <DISC Mode> screen.
On the source control screen, touch as follows:
Ejecting a disc
Display the pop-up short-cut menu, then
eject the disc.
• When removing a disc, pull it out horizontally.
• You can eject a disc while playing another AV source.
• If the ejected disc is not removed within 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust.
Playback operations
Audio playback information and key
operation
• For playback information, see “Source control screen”
on page6.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page7.
• If a disc does not have a disc menu, all tracks on it will
be played repeatedly until you change the source or
eject the disc.
• For playable disc types, file types and other
information, see pages44 and 45.
• If “ ” appears on the screen, the unit cannot accept
the operation you have tried to do.
–In some cases, without showing “ ”, operations
will not be accepted.
• When playing back a multi-channel encoded disc,
the multi-channel signals are downmixed.
Inserting a disc
Label side up
The source changes to “DISC” and playback starts.
• The IN indicator lights up while a disc is inserted.
9
ENGLISH
00_KWV_2019ST_EQ_EN.indb 900_KWV_2019ST_EQ_EN.indb 9 29/6/2018 11:56:59 AM29/6/2018 11:56:59 AM

DiscDisc
2 Make the settings.
<Menu Language>*1
Select the initial disc menu language.
(Initial:
KW-V255DBT/KW-V250BT Region 2: English
KW-V250BT Region 5: Russian)
<Subtitle Language>*1
Select the initial subtitle language or turn subtitles
off (Off). (Initial: English)
<Audio Language>*1
Select the initial audio language. (Initial: English)
<Dynamic Range Control>
You can change the dynamic range while playing
Dolby Audio encoded discs.
• Wide: Reproduces powerful sound at a low
volume level with its full dynamic range.
• Normal: Reduces the dynamic range a little.
• Dialog (Initial): Reproduces movie dialog more
clearly.
<Down Mix>
When playing back a multi-channel disc, this
setting affects the signals reproduced through the
front and/or rear speakers.
• Dolby Surround: Reproduces multi-channel
surround sound by connecting an amplifier
compatible with Dolby Surround.
• Stereo (Initial): Reproduces stereo playback
sound.
<Screen Ratio>
Select the monitor type to watch a wide screen
picture on the external monitor.
16:9 (Initial) 4:3 LB 4:3 PS
<File Type>*2
Select the playback file type when a disc contains
different types of files.
• Audio: Plays back audio files.
• Still image: Plays back still picture files.
• Video: Plays back video files.
• Audio&Video (Initial): Plays back audio files and
video files.
*1 For list of language codes, see page46.
*2 For playable file types, see page44.
If the disc contains no files of the selected type, the existing
files are played in the following priority: audio, video, then still
picture. You can change these settings only while playback is
stopped.
VideoVideo
Playback operations
Video playback information on the source
control screen
E.g. Video playback source control screen
1Media type
2Playback status
3Current playback item information
(title no./chapter no./folder no./file no./track no.)
4Playing time
5IN indicator (lights up while a disc is inserted)
6Playback mode indicator (Repeat/Random)
7File type indicator
10 ENGLISH
00_KWV_2019ST_EQ_EN.indb 1000_KWV_2019ST_EQ_EN.indb 10 29/6/2018 11:56:59 AM29/6/2018 11:56:59 AM

VideoVideo
[ ] Displays the aspect ratio selection
screen.
Touch [ Aspect] to select the aspect
ratio.
<Full>*2: For 16:9 original pictures
4:3 signal 16:9 signal
<Just>: For viewing 4:3 pictures
naturally on the wide screen
4:3 signal 16:9 signal
<Normal>*2: For 4:3 original pictures
4:3 signal 16:9 signal
<Auto>: For “DISC” source and
“USB” source only: The aspect ratio is
automatically selected to match the
incoming signals.
[ ] Displays the picture adjustment screen.
1Touch [DIM ON] or [DIM OFF] to
turn on or off the dimmer.
2Touch [+]/[–] to adjust the other
items.
• <Bright>: Adjusts the brightness
(−15 to +15).
• <Contrast>: Adjusts the contrast
(−10 to +10).
• <Black>: Adjusts the blackness
(−10 to +10).
• <Color>: Adjusts the color
(−10 to +10).
• <Tint>: Adjusts the tint (−10 to +10).
• <Sharpness>: Adjusts the sharpness
(−2 to +2).
[ ] Selects the audio type.
[ ] Selects the subtitle type.
[ ] Selects the view angle.
*1 When [ ] is set to <Just> or <Auto>, the picture is
zoomed with the aspect ratio of the <Full> setting.
This feature may not be used for some video sources.
*2 While DivX is played back with <Screen Ratio> set to [16:9]
(Page10 for discs/Page13 for USB), the aspect ratio may
not be set correctly.
Video menu control operations
You can display the video menu control during video
playback.
• Available operation keys differ depending on the
selected disc type and file type.
Video playback except VCD
E.g. Video menu control screen
Touching the operation keys performs the following
actions:
1
[ ]*1 Displays the picture size selection
screen.
1Touch [ Zoom] to change the
magnification level of the picture
(Zoom1, Zoom2, Zoom3, Full:
Initial).
2Touch [J] [K] [H] [I]to move the
zooming frame.
11
ENGLISH
00_KWV_2019ST_EQ_EN.indb 1100_KWV_2019ST_EQ_EN.indb 11 29/6/2018 11:56:59 AM29/6/2018 11:56:59 AM

2
[ MENU] Displays the disc menu (DVD).
[T MENU] Displays the disc menu (DVD).
[ ] Switches to the direct disc menu mode.
Touch the target item to select.
[ ] Displays the menu/scene selection
screen.
• [J] [K] [H] [I]: Selects an item.
• [Enter]: Confirms the selection.
• [Return]: Returns to the previous
screen.
Video playback for VCD
E.g. Video menu control screen
VideoVideo USBUSB
You can connect a USB mass storage class device such
as a USB memory, digital audio player, etc. to the unit.
• For playable file types and other information, see
pages44 and46.
• You cannot connect a PC or portable HDD to the
USB input terminal.
• You cannot connect a USB device via a USB hub.
Connecting a USB device
On the monitor panel
USB device
(commercially available)
The source changes to “USB” and playback starts.
• All tracks in the USB device will be played repeatedly
until you change the source or disconnect the USB
device.
Touching the operation keys performs the following
actions:
1
[ ]
Refer to “Video playback except VCD” on
page11.
[ ]
[ ]
2
[ MENU] Displays the disc menu.
[ ] Selects the audio channel
(ST: stereo, L: left, R: right).
[ ]*Displays or hides the direct selection
keys.
1Touch [DIR/CLR] to select a track
directly on a VCD.
2Touch the numbers ([0], [1] to [9]) to
select the desired track.
3Touch [Enter] to confirm.
To delete the last entry, touch [DIR/
CLR].
[Return] Displays the previous screen or menu.
* You need to stop playback to deactivate the PBC function when
playing a VCD with PBC activated.
12 ENGLISH
00_KWV_2019ST_EQ_EN.indb 1200_KWV_2019ST_EQ_EN.indb 12 29/6/2018 11:56:59 AM29/6/2018 11:56:59 AM

USBUSB
Selecting a folder/track on the list
1 Display the folder/track list.
On the source control screen, touch as follows:
2 Select the folder (1), then the item (2) in
the selected folder.
E.g. USB list screen
Select an item in each layer until you reach and
select the desired file.
Selecting a folder/track using alphabet
search
(Applicable only for audio file type)
You can search for a folder or an audio file by entering
the first letter you want to search for.
1 Select the list (folder or track) to search.
On the USB list screen, touch as follows:
• [ ]: Folder list
• [ ]: Track list
2 Enter the alphabet to search.
Touch the first letter you want to search for, then
touch [OK].
Settings for USB playback
1 Display the <USB Mode> screen.
On the source control screen, touch as follows:
2 Make the settings.
<Screen Ratio>
Select the monitor type to watch a wide screen
picture on the external monitor.
16:9 (Initial) 4:3 LB 4:3 PS
<Drive Select>
• Next: Switch between internal memory and the
memory source of the connected device (such as
a mobile phone).
Playback operations
Playback information and key operation
• For playback information, see “Source control screen”
on page6.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page7.
Selecting the file type to play
You can specify the file type to play.
E.g. USB source control screen
Select the file type as follows:
[Audio] Plays back audio files.
[Video] Plays back video files.
[Photo] Plays back still picture files.
If the USB device contains no files of the selected type,
the existing files are played in the following priority:
audio, video, then still picture. You can change these
settings only while playback is stopped.
13
ENGLISH
00_KWV_2019ST_EQ_EN.indb 1300_KWV_2019ST_EQ_EN.indb 13 29/6/2018 11:56:59 AM29/6/2018 11:56:59 AM

AndroidAndroid iPod/iPhoneiPod/iPhone
Connecting an iPod/iPhone
• For playable iPod/iPhone types and other
information, see page 47.
• You cannot watch video.
Wired connection
iPod/iPhone
Lightning model
(commercially available)
iPod/iPhone 30-pin
connector model
(commercially available)
On the
monitor panel
USB Audio cable
for iPod/iPhone:
KS-U62 (optional
accessory)
30-pin to USB cable
(accessory of iPod/
iPhone)
The source changes to “iPod” and playback starts.
Connecting an Android device
This unit supports Android OS 4.1 and above.
Android
(commercially available)
USB cable
(commercially available)
On the monitor panel
When connecting an Android device, “AUDIO MODE” is
shown. You can control Android device using a media
player application installed in the Android device.
Playback operations
Playback information and key operation
AUDIO MODE
Android
IWST
E.g. Android source control screen
Touching the operation keys performs the following
actions:
[S]/[T]Selects an audio file.
[IW]Starts/pauses playback.
14 ENGLISH
00_KWV_2019ST_EQ_EN.indb 1400_KWV_2019ST_EQ_EN.indb 14 29/6/2018 11:57:00 AM29/6/2018 11:57:00 AM

iPod/iPhoneiPod/iPhone
Bluetooth connection
Pair the iPod/iPhone with this unit via Bluetooth.
(Page24)
Selecting the playback device via the
connection method
See <Smartphone Setup> on page 36 for more
information.
Playback operations
Playback information and key operation
• For playback information, see “Source control screen”
on page6.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page7.
Additional keys operations: Touching the operation
keys performs the following actions.
[ ] Switches the device on the
<Smartphone Setup> screen.
(Page36)
Selecting an audio file from the menu
1 Display the audio menu.
On the source control screen, touch as follows:
2 Select a category (1), then select a
desired item (2).
Select an item in each layer until you reach and
select the desired file.
• Available categories differ depending on the type
of iPod/iPhone.
Settings for iPod/iPhone playback
1 Display the <iPod Mode> screen.
On the source control screen, touch as follows:
2 Make the settings.
<Artwork>
• ON (Initial): Shows the artworks of the playing
files.
• OFF: Hides the artworks of the playing files.
Listening to the radio
The unit switches to FM alarm scene automatically
when receiving an alarm signal from FM broadcast.
Playback information on the source control
screen
1Selects the band (AM/FM1/FM2/FM3)
2Text information
• Touching [H]scrolls the text if not all of the text
is shown.
• Touching [Radio Text] switches the information
between Radio Text, Radio Text Plus and PTY
code.
3Current station frequency
4Displays the preset stations window (Page17)
• To hide the window, touch [I].
5[P1] – [P5]
• (Touch) Selects a preset station.
• (Hold) Presets the current station.
TunerTuner
15ENGLISH
00_KWV_2019ST_EQ_EN.indb 1500_KWV_2019ST_EQ_EN.indb 15 29/6/2018 11:57:00 AM29/6/2018 11:57:00 AM

6Displays/hides other available operation keys*
7NEWS indicator
8AF indicator
9TI indicator
pOperation keys*
qST/MONO indicator
The ST indicator lights up when receiving an FM
stereo broadcast with sufficient signal strength.
wSeek mode indicator
eLO.S indicator
rRDS indicator
tEON indicator
The EON indicator lights up when a Radio Data
System station is sending EON signals.
* See the following “Operation keys on source control screen”.
Operation keys on source control screen
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• See also “Common operation keys on source control
screen” on page7.
Touching the operation keys performs the following
actions:
6
[SSM ]*1 (Hold) Presets stations automatically.
[MONO]*1 Activates monaural mode for better FM
reception (stereo effect will be lost).
• The MONO indicator lights up while
monaural mode is activated.
• To deactivate, touch [MONO] again.
[TI]*1 (For FM RDS features)
Activates TI standby reception mode.
• When TI is activated, the unit is ready
to switch to traffic information if
available. The TI indicator lights up in
white.
• If the TI indicator lights up in orange,
tune into another station providing
Radio Data System signals.
• The volume adjustment for Traffic
Information is automatically
memorized. The next time the unit
switches to Traffic Information, the
volume is set to the memorized level.
• To deactivate, touch [TI] again.
[MODE]*1 Change the settings for the selected
tuner reception on <Tuner Mode>
screen. (Page 17)
TunerTuner
p
[PTY]*1*2 (For FM RDS features)
Enters PTY search mode.
1Touch [PTY].
2Touch and hold a PTY code to search
for.
If there is a station broadcasting a
program of the same PTY code as you
have selected, that station is tuned in.
[SEEK] Changes the seek mode for [S]/[T].
• AUTO1 (Initial): Auto search
• AUTO2: Tunes in preset stations one
after another
• MANU: Manual search
[S]/[T]Searches for a station.
• The search method differs depending
on the selected seek mode (see
above).
*1 Appears only when FM is selected as the source.
*2 Only English/Spanish/French/German/Dutch/ Portuguese are
available for the text language here. If another language has
been selected in <Language> (Page 36), the text language
is set to English.
16 ENGLISH
00_KWV_2019ST_EQ_EN.indb 1600_KWV_2019ST_EQ_EN.indb 16 29/6/2018 11:57:00 AM29/6/2018 11:57:00 AM